Hand Tools

An electric vibration engraver is the only one that works satisfactorily.

You need a 1/4 Allen key .

Purchase a 4-way lug wrench from your local auto parts store.

Cross filing is done by pushing the file backwards and forwards at a slight angle to remove as much material as possible as quick as possible. Draw filing is done by using the file sideways along the edge of a piece to produce a good finish an remove very little material

Your local auto parts store

Keep the pliers dry and clean and use light oil on the pivot point about once a month.

A full set of both SAE and Metric wrenches, Allen keys and sockets. The sockets in 1/4 and 3/8 drive from 1/4 to 1 and 1/4 inch. -A full set of screwdriver bits, flat, Philips, Torx and Allen, a ratcheting screwdriver handle, at least 3 different size crescent wrenches and 2 sizes water pump pliers. Electrician pliers, 2 sizes long nose pliers, 2 sizes 'circlip' pliers. -That is a BASIC set of auto tools.

4.43 to 5.90 ft-lb. Please see the link.

Picture in the link below.

3/8 inch Allen socket 3/8 inch drive available at Bumber to Bumber Automotive stores

It is a kind of bit for use in a jack-hammer.

Wrenches come two ways, open ended and box end. Open end are just a U shape on the end. Box end go around the nut or bolt. If you were to slice a quarter inch off of a socket that is what the end of the wrench would look like.

yes

An electrician uses a screwdriver and insulating tape.

I changed the brakes on a 1997 Holden Barina SB today (21/5/11). You will need a 10mm Allen key to take off the brake housing. Do yourself a favour and buy a set of Allen key type attachments for a ratchet. Makes it much easier.

Assuming (as the cat is engineering) that you are using a round nosed cold steel chisel on a metal item. These were used to set in a dimple (dent) that would be used for decoration or its used to hammer in a channel for a liquid to move through similar to that inside a bearing. they were used before machinry to form a countersink that a retaining screw or rivet would sit into.

Mainly solder in as short a time as possible to avoid burning the traces causing them to lift. This means using a good quality temperature regulated iron that does not cool off when applied to the joint to be soldered and is not too hot either.

They lack the close fitting measurements that a dedicated tool would have . They also have a tendency to 'round off' the corners of the fastener itself due to a poor fit .

what the hex a wrench? Hex wrench is short for hexagonal wrench, that is a wrench or spanner designed to fit a certain size nut or bolt.

You need a 12 mm wrench, not Allen key.

An Allen key is used on an Allen screw. Each screw has a different key that must be used. If you do not have the appropriate key for the matching screw you will be unsuccessful in removing or inserting the screw.

The first primary schools were opened by the Byzantine Empire in 425 AD, and the system was maintained until 1453.

The earliest universities were medieval, and the system we use for university education is still based to some degree on medieval universities. The bachelor's, master's, and doctor's degrees are all medieval.

The oldest 70 or so schools and 60 or so universities were all founded in the Middle Ages.

The early universities tended to teach science and philosophy very dogmatically based on ancient texts. This tendency was broken by the Church through a series of actions called the Condemnations of 1210-1277. These freed scholars and scientists from the enforcement of traditional texts and allowed them to deal with science through empirical observation.

The oldest state run schools are medieval.

The Middle Ages introduced the first business oriented schools, called abacus schools.

I think the first coeducational schools were medieval, as the Byzantine primary schools were coeducational, as were a number of the abacus schools.

Please see the related links below for more education.

The standard screwdriver is designed to turn screws in or out.

The dagger axe is a medieval weapon.

I have steel rules that are marked down to 1/64 of an inch.