0
Honda Civic EX
The EX is a rebadged sixth-generation model of the Honda Civic. Available as a sedan or coupe, it features a remote entry system, high-horsepower VTEC engine, power sunroof, body-colored side mirrors and side moldings.
3,295 Questions
What is the front leg room in the 2006 Honda Civic?
The 2006 Honda Civic has 42.6 in. of front leg room.
What engine fits a civic 1996?
standard engines are d-series such as d16 or d15 engines. you can put in a b series if you want. look one website for a swap kit with everything you need. www.jspecautosports.com
How do you change the alternator for a 1992 Honda Civic?
Here are the relatively easy steps I took. The alternator is difficult to access, and cannot be removed without removing something--preferrably the easiest thing. # Turn the steering all the way to the left (makes things easier) # Disconnect the battery ground wire. # Jack up the car and remove the front driver's side wheel. # Remove the 2 alternator mounting bolts. Access to top bolt from top, bottom bolt from underneath. # From top or underneath (both are difficult access), rotate alternator so you can remove all the wiring (one plug, one wire wired to the post, and one retaining clamp on the back). # From underneath, move alternator back behind the engine to clear it from the alternator mounting bracket. # From underneath, remove alternator mounting bracket. Two 14 mm bolts (need a socket for one of them). # From side, in wheel well, unscrew back-most plastic screw holding front inside wheel-well splash guard on. # Pull Alternator out just behind the splash guard, flexing it out as you go. # Put the new alternator back in through the same hole. # Set the alternator aside and put the alternator mounting bracket on--tighten it up because you won't be able to access one of the bolts once you put the alternator on.
Notes:
You might want to make sure that the new alternator will fit in the mounting bracket while both new alternator and bracket are off the car. Sometimes the bolt sleeve in the bracket can be too tight and need a little tap to move it out.
You will probably lose the wheel well nut behind the plastic screw retaining the wheel well splash guard; mine fell into the body frame, never to be seen again. To fasten it back, I just used a pinched piece of coat-hanger wire to hook the wheel well back in place and then put some silicone on the hole so that water didn't go into the hole.
How much does it cost to fix the radiator support on a 1991 Honda civic DX?
Not much at all. Be careful which place you go to. Some places love to use genuine Honda parts which is NOT needed for a support (unless it's an engine mount), just use a piece of metal and make your own support for CHEAP!
How many gallons of gas does a 1987 Honda civic hatch back hold?
10.5 U.S. gallons, according to my owners manual and my purchase of gas for the last 7 years.
What size of tires does the 1996 Honda Civic LX have?
OEM size of 185/65-14 is listed on the drivers door post.
Where is the relay switch located on a 1990 Honda Civic DX?
Ours is a 1990 Honda Concerto. Right hand drive (Australia) The relay is located in the centre console behind the radio, so easily accessible.
It sounds like the transmission valve body is getting old and tired. It could also be a partially plugged transmission filter. Try getting the transmission fluid changed. If that doesn't help you can sometimes get few extra miles out of an old, tired transmission by adding a little transmission seal conditioner such as Trans-X.
For a 2001 Honda Civic, the P0730 code means there is an issue with the shift control system. Dirty transmission fluid is one of the many things that can cause this code.
Where is and how do you replace the speed sensor on 1992 Honda Civic DX?
I have a Honda Civic 99 LX 1.6 Aut, and the D4 is Flashing and the gears doesn't shift at all, some people say that the speed sensor e some others don't even know what the heck it is... Does anyone with more knowledge than me could help me with this. How can I know if the speed sensor is dead, is there anyway to find out?
And where the speed sensor is located so I can remove and see it? Thanks a lot in advance. Ivan
A header is a part of you exaust system all it is, is pipes coming of you exaust manifold usually the pipes will go 4-2 an then 2-1 they just combine into each other
How do you remove a roof mount antenna on a 2003 Honda Civic Hybrid?
Just been looking into this myself matey as snapped my mount in car wash on new years eve. Looking at the civic manual I bought on eBay ages ago it seems you have to remove the trims in front and behind your door (pillars) and then the pillar above your seat belts. take out the ceiling and rear ceiling lights. remove sunvisors and grab handles. remove the weatherproof seal around the boot and then finally you can get to remove the headliner (the carpet on your roof for people like me!!) Its a big job! Am wondering whether to pay Honda to do mine as its a 2man job as well apparently and knowing Honda they put 1 way clips in everything so when you pull them off they snap!!! That happens when you remove the plastic triangle hidding bolts to wingmirrors. Oh and if you've got a sunroof you have to undo a plug and remove the moonroof switch whatever that is but I don't know as mine hasn't! Hope this helps a bit. Chris
--------------------------------------------------------------------------------------------------------
Its not nearly that difficult. Remove the light covers and then unscrew and remove the light fixture that is directly behind the rear-view mirror, you will see a silver cap sticking through the roof that has a black wire attached. Using a small flat screwdriver remove this cap, and you will find an 8mm nut that is holding the antenna onto your roof.
What would cause oil to be splattered under hood of a 2003 kia sedona?
blowby caused either by worn or broken piston rings and or valves May want to check for missing dipstick, oil filler cap etc.
How much should the replacement of an oxygen sensor cost?
ine was $89.99 at schuck's auto parts.. call around
parts at napa cost 4 sensors 2 @65 2 @53
How do you remove the radio from a 1999 Honda Civic?
it's easy to do...too much to write on here...i'm going to refer you to www.installdoctor.com you will find it easy to find on here! :)
See this website, below in the related links and sources, for more information and help.
IF its doing this only when it warms up, it might be a bad coil - is it getting gas?
What kind of headers can you install on your 95 Yukon that won't mess up for the smog check?
You might want to double check, but GM was using "Header-Like" exhaust manifolds from the factory. If that's the case, you won't get much improvement by putting on headers.
How can you make your civic faster?
the cheapest and most effective option is to add a cold air intake.
generally in the range of 100-300 dollars, although you can find them cheaper on eBay or craigslist.
hands down, the most cost effective and performance enhancing modification you can make to a stock civic.
some intakes will give you as much as a 18whp boost.
see PASSWORD JDM: Whale Penis Intake.
What causes 2005 Ford E 150 to idle low and die in gear?
if I were you I'll check the transmission fluid level, happen to me not to long ago, I have Plymouth grand voyager, run ruff, then could'n go forward or backward, had no or very little transmission fluid. If your transmission fluid is ok, maybe it due to be change, light or dark brown fluid, change it.
===========================================================
IGNORE THE ABOVE - IT HAS NO BEARING ON THIS PROBLEM ON FORD VEHICLES!
Ford has a Technical Service Bulletin on this specific problem. It involves reprogramming the PCM with an update to include a "sludge compensation stategy for the throttle body". It must be done by a dealer, and shouldn't cost more than $30 - $50.
A temporary fix might be to remove the air intake and filter ducts and use carb cleaner inside the throttle body, and a good quality electronics cleaner on the Mass Air Flow sensor.
!!!DO NOT USE CARB CLEANER ON THE MAF SENSOR!!!
The electronics cleaner you use on the MAF sensor must be of the type that leaves no residue behind. A good one, if you can find it, is LPS Industries "CRC Free". There are others.
No guarantees on how well, or how long, this might work, but it's worth a try.
