0
Hyundai Accent
The Hyundai Accent is a subcompact car produced from 1994 to the present. The Accent was named by J.D. Power and Associates as 2008’s most dependable subcompact car.
1,367 Questions
That is your "Low Tire" light. It is confusing. It looks like a horseshoe with an exclamation mark in it and water at the bottom, but it is supposed to be a picture of a tire with low pressure with an exclamation mark in it. Great art it's not. Check your tire pressure. If the "TPMS" letters also come on along with the wet horseshoe, though, it means there is a problem in the Tire Pressure Monitoring System. In that case, have a computer-equipped mechanic look at it.
How wide is the 2002 Hyundai Accent?
The 2002 Hyundai Accent is 5 ft. 5.7 in. (65.7 in.)12V front power outlet(s) wide.
How do you remove a broken key from the ignition of a 1998 Hyundai accent?
one way is to "tweeze" out the key end with very thin tweezers and use a very small amount of super~glue on the tips that will be touching the key end sides stuck in the ignition. give the glue a chance to freeze then "gingerly" ease out the key end from the ignition slot.
if you can't find tweezers then you may be able take a very thin straight edge screwdriver with again using super~glue (sparingly) with a steady hand you will glue the screwdriver to the broken key and try to pull it out of the ignition once the glue has set up.
(try not to get super~glue on anything else but the screwdriver& the key)
Good Luck and have patients .
How do you remove speakers from front door pads of Hyundai accent car?
ta ke the front doors off, they are screwed into the door fame!
I have a 2000 Hyundai Accent and recently replaced my entire streo system.
How do you search for Hyundai accent auto parts?
You can search online on internet through Google. On Google you will get best result of Auto Part Dealers in your area.
Why are the brake lights staying on in a 2001 Hyundai?
My problem was a stuck /broken plastic part on break lever .new part is a few bucks.
Zev
How can you reset the SRS light to Acura RSX 2002?
Our cars are known to have problems with the SRS lights, well basically all Honda/Acura because the system sometimes "hiccups" and causing codes to trip the SRS light.
DISCLAIMER: Please do this at your own risk, i am not responsible for any damages that you may cause by doing this SRS DIY reset. If you do not trust yourself, please take the car to Acura Dealership and have them reset it for you, Warranty will normally cover for reset at FREE of charge. Try this DIY at your own risk.
Note: If your airbag deployed or seats has been removed or anything that may have triggered the SRS, this DIY will not work for you. All you will get is two flashes or more and the light will remain on.
Tools Material Needed:
- Standard Paperclip (or wire)
- Maybe flash light (night job)
Time:
- 1 to 5 minutes
First make sure your key is out of the ignition.
Step 1:
You can use two options in this step to use to make two contact connect together:
Paper Clip, you can use the paperclip and bend it out to where both ends are next to each other so it can be put in to two pins.[img]http://www.dc5nation.com/DIY/SRSDSC02850.JPG[/img]
- or -
Regular wires, this is actually the best way to use to complete a circuit.
[img]http://www.dc5nation.com/DIY/SRSDSC07465.JPG[/img]
Step 2:
Remove the bottom panel under the dash, two twist clips which can be easily taken off. (turn counter-clockwise)
[img]http://www.dc5nation.com/DIY/SRSDSC02851%20copy.jpg[/img]
Step 3:
After the bottom panel is exposed, locate the fuse box (see drawing for location)
[img]http://www.dc5nation.com/DIY/SRSDSC02852%20copy.jpg[/img]
Step 4:
Locate the SRS plug above the fuses in the fuse box panel, you will see a yellow clip in the middle left side. It is also the ONLY plug that's yellow in the fuse box panel.
[img]http://www.dc5nation.com/DIY/SRSDSC02853%20copy.jpg[/img]
Step 5:
Unplug the clip. You should see two pin holes that you will be completing the circuit with using the paper clip or wires
[img]http://www.dc5nation.com/DIY/SRSDSC02857.JPG[/img]
Step 6:
plug the paperclip in to the 2-pin clip.
[img]http://www.dc5nation.com/DIY/SRSDSC02859.JPG[/img]
After all the Prep Work is done, here comes the steps you need to take to complete actually reset the light. TIMING MUST BE PERFECT, if the light comes back on, remove the key and repeat steps again. Read these steps first before attempting the reset.
Step 7:
With the paperclip or wires in the pins, place the key in and click to the Ingition On position II and leave it alone throughout the whole step.
[img]http://www.dc5nation.com/DIY/SRSDSC02865.JPG[/img]
Step 8:
You should hear beeps for 3 seconds, and when the beep is gone, the SRS should turn OFF.
[img]http://www.dc5nation.com/DIY/SRSDSC02864.JPG[/img]
Step 9:
QUICKLY, Take the paperclip/wires out and the light should come back on.
[img]http://www.dc5nation.com/DIY/SRSDSC02861.JPG[/img]
Step 10:
When the light comes on, QUICKLY plug the paperclip back in to complete the curcuit again, in a second or so, the SRS light should TURN off
Step 11:
At the final step here, you will remove the paperclip/wire and the light will quickly flash twice and turn off. You should wait a second or two to see if the light comes back, if so, YOU WILL NEED TO REPEAT steps 7-11 again. If not, read step 12
Step 12:
At this point, take the key out of the ignition and put the 2-pin clip back in to the proper place (same place where you took it out). Secure the bottom dash back in to place. Test out the SRS again with the Ignition Position II. It should beep then the SRS should turn off.
Quick Read DIY without pictures:
1. connect clip to yellow clip, turn key to position II
2. wait for the light to go off and remove the paper clip/wire.
3. As soon as the light turns back on, quickly connect the circuit again.
4. The light should turn back off. Remove the paperclip/wire again.
5. The light will wait a second or two before it tells you the follow word.
6. Final word is, 2 quick flashes and SRS light turns off completely.
6-A. two quick flashes and the light remains, you may be too slow or you have a short in your SRS somewhere.
7. turn off ignition and put back the clip.
Congratulations, you have successfully reset your SRS light.
Troubleshoot:
Most of the errors can cause by removing items such as steering wheel, seats, seatbelts and airbags. Its very rare for a sensor in the front to go bad but if you have been in to an accident and your airbag didn't deploy but the seatbelt locked, YOU MUST replace the SRS module.
If you have aftermarket steering wheel or seats, there is a resistor that you can purchase from Radio Shack where you stick in between those where the airbag or seats suppose to be and act to complete the circuit.
How do you fix the timing belt on a 1996 Hyundai Accent?
I presume you mean by fixing the belt you mean you want to change it. Firstly turn the crank shaft pulley so that the engine is at top dead centre (TDC) then turn the steering to the right which gives you access under the front wing to the crank shaft pulley bolt. Put the car in top gear and have someone step on the brake pedal while you loosen the bolt using a 19mm socket on an extension. Next, remove the drive belts for the alternator and the power steering by loosening the adjusting bolts on these items. Take off the water pump pulley by removing the 4 10mm bolts which are in the recess at the centre of the pulley. This gives you access to the plastic timing belt cover bolts. Remove the timing cover bolts and the timing belt cover. Slacken the bolt in the timing belt tensioner to release the tension and remove the belt. Refitting is a reverse of the above procedure. Use a screwdriver or something similar to push down on the timing belt tensioner to tension the belt. The belt tension should be such that you should be able to twist the belt at its longest section by no more than 90 degrees.
How do you fix a problem with a Hyundai accent 2002 heater?
go to your Hyundai dealer and make it check
What size wipers are on 2005 hyundai accent?
The 2005 Hyundai Accent takes 20" drivers and 18" passenger side wiper blades. See sources and related links below for more information. Since there are over 22 different wiper arm attachments, do not buy wipers just by length only. Be sure to lookup exact wiper blade part numbers by vehicle make, model and year for the brand wiper you decide to purchase. This ensures correct length AND correct attachment.
How much would it cost to change shock absorbers on a 1998 Hyundai Accent?
Apparantly, you cant just do the struts, the struts and springs come combined. my two front sets on my 1999 installed cost me $800CDN.
To what torque must the bolts on the head of a 2000 Hyundai accent be tightened?
to what torque must the bolts on the head of a 2000 Hyundai accent be tightened?
Does the check engine light come on in the 2009 Hyundai accent when it is time for an oil change?
No, the check engine light means there is a problem with the emissions system. The maintenance required light means something like an oil change needs to be done.
What is the spark plug gap for a 1999 Hyundai accent 1.5 l engine?
Gap is .044
Hyundai Accent
1.6 liter DOHC L4
Firing order: 1-3-4-2
Firewall
1*2*3*4
Radiator
How do you adjust emergency-brake cable on a 2001 Hyundai accent?
there is a cup holder just behind the emergency brake handle, on the sides of the cup holder are two screws, unscrew them, then use a spanner don't remember the size, and just adjust the bolt to the right while testing the tension using the handle, The brake shoes mechanisms are self adjusting in this 01' accent, but at times u need the adjust the bolt.
What are some reasons for your 2001 Hyundai Accent to be burning lots of gas and reving high?
Mine is doing exactly the same thing. Is your check engine light on? Mine is constantly. What I have discovered is:
1. One of my Oxygen sensors is bad (bank 1 sensor 2, heater circuit) whatever that means. That's what the code is in the computer. 2. It does not shift into overdrive. Make sure the overdrive switch is on. If it is on, then there may be something wrong with your transmission. My overdrive switch is probably bad, because not knowing any better, I used to sit at red lights and flick it on and off repeatedly, very fast, not realizing that could ruin the switch. So now it never goes into overdrive, but the weird thing is, the dashboard light that says "O/D off" never lights up, and I can't figure that one out.
I ordered an OBD-2 scanner off of eBay to keep an eye on the codes for the check engine light. Any time they've ever been checked, they've always said it's because of the Oxygen sensor. It's $50 for me to get the codes checked, but I bought a scanner off eBay for $20. I also ordered the actual shop manuals off eBay as well. A little more expensive, but i think they will be worth it.
So my advice is if the Check Engine light is on, get the codes checked, but if it's the same problem as mine, it's just not going into overdrive.
Hope this helps.
bank 1 sensor 2 is the oxy sensor located on the exhaust pipe under the car just past the engine is fairly esy to change yourself
How do you take off the drivers side Exterior door handle on a 2002 Hyundai Accent?
its has like a safety pin in the handle where u roll down the window you have to pop off with a flat head screwier driver
How do you replace a rear window regulator on a 2002 Hyundai Accent?
The tools you will need:
A #2 Phillips head screwdriver. A Standard head screwdriver. A 10mm Socket and ratchet.
First take out all of the screws in the door panel. There is one in the handle that opens the door, and 2 in the door panel handle. Use the flat screwdriver to pop off the covers. Taking out the door handle is a little tricky. Slide it towards the front of the car and pull out. You might not get it the first try. Once you get the handle out enough, you will be able to see 2 metal rods connecting to it(towards the back of the car). Using the standard screwdriver, pull the plastic piece(either blue or red) towards you and it should unclip from the rod. Next, pick up on the rods and they should come out of the handle. Once all screws and the door handle are removed, you can take off the panel.
To remove the door panel, simply pull it off, starting at the bottom of the door and prying your fingers between the panel and the door. You will hear a series of pops. You didn't break anything. If it doesn't come fairly easy, don't pull too hard. You may have missed a screw. Once the panel swings freely on the window slot, get it close to the door and pick up, as the top rests in the window slot. If you have power windows, you will have to unclip the wires going to the switch.
Once the panel is off, drop the window and remove the 2 Phillips screws holding the window on the track. After the window is off, tape it up so it is out of your way. Next, take the socket and remove the 3 nuts holding the window motor, (towards the front of the car, in the middle), and then the three(maybe four) that hold the metal track in place. Once those are off, good luck getting out the hole in the bottom of the door. It will not free fall in the door as the stud screws are attached to the motor and regulator. You will also have to disconnect the motor wire. Once it is out of the door, there are 3 screws or bolts that hold the motor to the regulator. take those out and the motor should slide off easily. Then do it in reverse to put it back together.
Where is the oil pan on a 2006 Hyundai accent?
Oil pans on all cars are located on the bottom of the engine. Often a square shape with a distinctive bolt that sits diagonal on the corner of the oil pan.
How do you take the door panel off of a 1997 Hyundai Accent?
There are about four (or five) "star" screws which you will need the Phillips screw drive to remove them. look around for the screws on the ages of the plastic panel,
one other screw requires you to remove the inside door handle there is also a centre screw, make sure to remove it then put the inside lock button on open then try to pull out the door handle.
When you pull the inside door handle locate two mechanism they are the size of a 4mm wire, you will need a small flat screw drive to slide off the plastic clips that hold the open and lock door mechanism.
when the door hand is off and the screws out as well, roll down you window, actually roll it down before hand. then remove the door panel by lifting from the bottom upwards. You will have to apply a bit pressure to remove the edges of the windows since the mirror adjuster seats right on top of where the panel needs to come of lift from the side of the outside door handle lifting upwards and then move backwards towards the back door.
What is the basic warranty on the 2014 Hyundai Accent?
The 2014 Hyundai Accent has a 5 yr./ 60000 mi. basic warranty.
Where can you find a Factory radio wiring diagram for a 2000 Hyundai accent?
www.factoryautomanuals.com may provide the exact guide, however a fee is involved.
Your windshield wipers for your 2001 Hyundai accent won't work why?
there could be a number of reasons. start with the switch,a loose/corroded conection,fuse,relay and the motor it self. check to see if you got "juice" going in to the motor if you do the problem may be the motor or a bad ground connection.(its pretty simple to test with just a test light)
It is most likely the wiper motor transmission assembly. They cost around $80 at the dealer. I had to have mine replaced on my 01 Accent and they said it is a common problem on the Accent because water gets in there and it corrodes causing it to seize up. It shows all the same symptoms as a bad wiper motor but when a new motor is put on it will not work and it will keep blowing the fuse. I'm not sure how hard the assembly is to install. Dealer can get the part but independent mechanic will charge a lot less to install it.
