Infiniti G35

63 kph

Type in G35 Air filter change in youtube and "bythebay" is the one giving the tutorial. Be is reputable at DIYs Do It Yourself videos.

most likely it is a problem with the bushings in your compression rods. The dealers used to replace the entire rods but now I think they just replace the worn part - I think there is a TSB on it. Check infinitihelp.com for the TSB and talk to your local dealer to get the issue resolved.

It's Infiniti not "Infinity".

It should be near your VDC OFF button which is near your interior light dim switch, if you don't know where these are.. they are on the left-hand side of the driver's steering wheel. It's a weird looking trunk release where you just push the button in.

This should help: http://g35driver.com/forums/archive/index.php/t-163319.html

To begin, press and hold the 2 outer

HomeLink buttons (to clear the memory)

until the indicator light blinks slowly (after

20 seconds). Release both buttons.

Position the end of the hand-held transmitter

1-3 inches away from the HomeLink

surface.

3. Using both hands, simultaneously press

and hold both the HomeLink button you

want to program and the hand-held transmitter

button.

DO NOT release the buttons until step 4

has been completed.

4. Hold down both buttons until the indicator

light on the HomeLink flashes, changing

from a "slow blink" to a "rapidly flashing

blink". This could take up to 90 seconds.

When the indicator light flashes rapidly,

both buttons may be released. The rapidly

flashing light indicates successful programming.

To activate the garage door or other

programmed device, press and hold the

programmed HomeLink button - releasing

when the device begins to activate.

5. If the indicator light on the HomeLink

blinks rapidly for two seconds and then

turns solid, HomeLink has picked up a

"rolling code" garage door opener signal.

You will need to proceed with the next steps

to train the HomeLink to complete the

programming which may require a ladder

and another person for convenience.

6. Press and release the "smart" or "learn"

program button located on the garage door

opener's motor to activate the "training

mode". This button is usually located near

the antenna wire that hangs down from the

motor. If the wire originates from under a

light lens, you will need to remove the lens

to access the program button.

For housings:

1. Google DIY Headlight removal G35

2. Follow the guide.

Quick rundown:

1. Remove front bumper using the appropriate tools.

2. Un-bolt the headlight housing, detach all plugs/wires.

3. Reverse to complete.

For bulbs :

Google it. There's a complete DIY guide with pictures on how to do it.

Quick rundown:

1. (Optional) Lift the front of the G35 and place it on jack stands. Remove both front wheels, place them under the car if you don't have jack stands.

-If you don't do this then turn your wheels to which direction giving you more space to fit your arm through the fender-

2. Remove fender lining using a flathead screw driver.

3. Stick your arm through and make your way up to the headlight and blindly feel for the bulb. Once you find it, un-plug it as you would on a normal car and remove the bulb as you retract your arm.

4. Do the same thing to put in a new bulb being very cautious as to not damaging the new bulb on anything.

5. Repeat on opposite side if necessary.

6. Reverse the removal of everything to complete.

This "question" isn't even a question.

WARNING:

Never remove the radiator cap when the engine is hot. Serious burns could occur from high pressure

engine coolant escaping from the radiator.

REMOVAL

1. Remove engine cover with power tool. Refer to EM-18, "INTAKE MANIFOLD COLLECTOR" .

2. Remove undercover with power tool.

3. Drain engine coolant from radiator. Refer to CO-11, "Changing Engine Coolant" .

CAUTION:

Perform when the engine is cold.

4. Disconnect A/T fluid cooler hoses. (A/T models)

Install blind plug to avoid leakage of A/T fluid.

5. Remove air duct (inlet) and air cleaner case. Refer to EM-16, "AIR CLEANER AND AIR DUCT" .

6. Remove bracket mounting bolt for anchoring A/C piping from vehicle left side, so that A/C piping can be

moved.

7. Remove reservoir tank and bracket.

8. Remove radiator hoses (upper and lower) and reservoir tank hose.

CAUTION:

Be careful not to allow engine coolant to contact drive belts.

1. Reservoir tank 2. Cap 3. Reservoir tank hose

4. Radiator hose (upper) 5. Radiator cap 6. Upper mount bracket

7. Mounting rubber (upper) 8. Radiator 9. Radiator hose (lower)

10. Mounting rubber (lower) 11. Drain plug 12. O-ring

13. Radiator cooling fan assembly 14. Bracket

PBIC1984E

CO-16

RADIATOR

Revision; 2004 April 2003 G35 Sedan

9. Remove radiator cooling fan assembly. Refer to CO-24, "Removal and Installation (Motor Driven) (M/T

Models)" . (M/T models)

10. Remove radiator shroud (lower). (A/T models)

While pressing left and right pawls in direction indicated by

arrows, pull lower radiator shroud toward you to remove.

11. Remove radiator shroud. (A/T models)

12. Remove cooling fan. Refer to CO-22, "Removal and Installation (Crankshaft Driven Type) (A/T Models)" .

(A/T models)

13. Rotate two radiator upper mount brackets 90 degrees in the

direction as shown in the figure, and remove them.

14. Remove two A/C condenser mounting bolts located in upper

part of radiator.

15. Remove radiator as follows:

CAUTION:

Do not damage or scratch A/C condenser and radiator core when removing.

a. With lifting and pulling radiator in a rear direction, disassemble

lower mount from radiator core support center.

CAUTION:

Because A/C condenser is onto the front-lower portion of

radiator, moving to rear direction should be at minimum.

PBIC0838E

PBIC0839E

PBIC0840E

PBIC1936E

RADIATOR

CO-17

C

D

E

F

G

H

I

J

K

L

M

A

CO

Revision; 2004 April 2003 G35 Sedan

b. Lift A/C condenser up and remove radiator after disengaging the

fitting as front-bottom surface.

CAUTION:

Lifting A/C condenser should be minimum to prevent a load

to A/C piping.

c. After removing radiator, put A/C condenser on radiator core support

center to prevent a load to A/C piping, and temporarily fix it

with a rope or similar means.

It indicates the battery life left in your key fob battery.

About 3 days!

1. Press and hold garage door opener 1 and 3 in your G35 until the light blinks

2. Take the remote you use to get into your house and press and hold the button near the rear view mirror. At the same time press and hold the button you would like to program for that door. The light will start blinking slowly and then faster. Let go of the buttons

3. Go into your garage and press the learn button on your garage door opener. These are different colors depending on the make and model.

4. within 30 seconds press and hold the button you programmed in your car until the light in your garage blinks.

The stock rating for OEM bulbs is 4300K or Kelvin. You can "upgrade" to more intense bulbs 6000K, 8000K, 10000K. But from my understanding they will not put out as much usable light. Stay around 5-6K. OEM replacements are 100 dollars each from oemacuraparts.com

The OEMS are made by Osram. They are a D2R style or format.

SAE 5w-30 conventional or synthetic energy conserving oil any major brand.

G35 can fit a 285/35 20" in the back. Probably a 265 up front.

i drive an s2000. with equal driving, i would say a 350z has a very slight edge over an s2000 if both are stock. throw an engine chip or an intake in an s2000 and it is just about equal from my experience.

No. The coupe and sedan have completely different front and rear bumpers.

Expect 22.5-24 in mixed driving with the manual transmission. Since I tend to spend a bit more time on a highway, I average 24 to 24.5 with 93 Octance, Mobile One synthetic oil and some "spirited" driving now and then. On stretches of highway at 70mph, you can get 29 or better. Properly inflate your tires and keep them balanced and aligned.

when changing the oil on a new car I typically change it when the car has 1000-1500mi on it since the new engine is breaking in. the reason is you typically get small amounts of metal in the oil since the new engine is breaking in and the parts are bonding together

Your Brake rotors are warped... Remove them and have them turned or replace them.

It's easy; I changed mine and I know nothing about cars. You have to pop off the little plastic bolts that hold down the cover for the battery. Then disconnect the battery. Take it out and put the new battery in and re-connect the battery. Done.

Another Answer:

This is the very first time ever, in my entire life, that I replaced the battery on my Infiniti G35 2006 by myself.

Steps:

1- remove the clip button with flat screw driver (about 4-5 clips)

2- take the big piece that holds the battery cover

3- loosen the NEGATIVE screw on battery and remove the cable out of its charge from battery

4- loosen the POSITIVE screw on battery and remove the cable out of its charge from battery

5- take out battery - it's heavy

Note: it's easy to take out because the original battery is smaller. If you buy the same size as the original, then it won't be hard to install it. My new battery is a bit bigger than the original and still fit in the battery slot; however, it's a bit difficult to put it in. Try to be gentle, and you can put it in perfectly.

6- Once you put in the battery, put the POSITIVE charge back on first and tighten up the screw

7- then put the NEGATIVE charge on second and tight up the screw.

At this point, once you have the negative charge touch the charge on battery, the alarm is on. This is the sign for you to know that it works.

8- Now put everything back where it belongs. By the way, the clips are easy to put back on. If you pull the piece underneath the screw all the way down with the 4 clips on the side of screw out then put it back in the whole and push it down. It will lock after the screw push down.

The Goodyear Eagle's are NOISY after initial break-in.

its located in the valve body of the transmission