0
Mazda Protege
Also known as Familia in some markets, the Protégé was a compact car produced by Mazda Motor Corporation from 1964-2003 for the North American market. The Protégé was one of the company’s best sellers and was manufactured in eight generation models.
1,312 Questions
Where do you find the fuse panel for a 2000 Mazda protege?
Look in the owner's manual??
well there are two actually, the first one (the one you probably need) is located by your left foot when you're sitting in the drivers seat and the other is located under the hood on the right
look for a break in the wiring. it might be grounded on something
How do you replace alternator belt Mazda 323?
(this assumes it is a car similar to the 1988-1993 generation Mazda 323)
First, you need to take off the belt to the power steering pump. To get it off, you need to open two screws that hold the pump in place, and then slacken the belt with the tensioner screw.
When that belt is off, you do a similar thing with the alternator belt. Loosen the bolts that hold the alternator in place, and you can move it a bit so the belt slackens.
Same thing in reverse to get it back on again. The belt should move a centimeter or so when properly tensioned. You can't go by the slack of the old belt, since worn belts are usually way too loose. If the belt slips (and starts "screeching"), it's too loose. You may need to tighten it a bit after it's been "worn in".
see if your local library has a shop manual to use for free.. I'd get a manual if your going to keep the car d
What type of transmission fluid is required for a Mazda 2001?
Use Mazda ATF M-V or Dexron III. Either one is acceptable.
How do you change sway bar links on a 1999 Mazda Protege?
For the rear sway bar links, its a bolt on part. So you have to put your two rear tires on ramps to lift them up for a good 6-12 inches off the ground to give room to operate; or just lift one rear wheel at a time with a standard jack. You might have to remove the tire if you want more comfortability while operating underneath the car. Then unbolt the link with a socket wrench or a tool, it has two bolts on it. Sometimes its jammed in there so just crack the bolt with a bolt cutter if needed. After you've taken the old link off just install the new link by bolting it on. Remember to line it up correctly and put enough torque on the bolt so its safely fastened to the sway bar. Lower the side you worked on and do the whole procedure for the other side. Its pretty easy!!!
1990 Mazda protege 1.8 L Torque head bolts?
Mazda Protoge 1990 1994
Torque specification for head bolt is 56-60 pound per ft
In three steps start from center of the head
8 4 1 6 9
7 3 2 5 10
Where is the PCM located in a Mazda Protege 1996?
Under the console directly under radio and hvac controls
On a 2003 Mazda Pretege 5 what is the meaning of dtc 1175 and dtc 1235?
Trouble code P1175 means: Cam Control Trouble code P1235 means: Fuel Pump Control Circuit
The tension bolt should not be removed. The four bolts holding the alternator in place need to be removed, the loosening tension bolt will give enough slack to get the belt off.
How much horsepower does a 1994 Mazda protege have stock?
base model and DX have 103 HP. LX model has 125
Where is the horn fuse on a 2002 Mazda Protege?
The fuse for the horn should be on the drivers side underneath the dash. There is a diagram on it that shows the horn fuse.
Where is the starter on a 97 Mazda Protege 1.5?
starter on a 1.5 is located on rear of block under intake manifold. 3 bolts hold it in place ..2 are accessed from top of engine and third is accessed from below.
How do you replace the thermostat located on a 1998 Mazda Protege?
Follow the upper rad hose from the radiator to the engine and you will find a housing thas has the thermostat. Take the housing off and when you reinstall the thermsotat, make sure the spring is toward the engine.
How do you replace the spoiler brake light bulb on a 2003 Mazda Protege?
2003 Mazda Protege center high mount stop (third 3rd brake light) light bulb lamp replacement procedure: Purchase the correct replacement center high mount stop (third 3rd brake light) bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement bulb information. Then consult your owner's manual for the center high mount stop (third 3rd brake light) bulb replacement procedure. As simple as it sounds, the owner's manual is the best place to start for bulb replacement instructions and illustrations. If there are multiple bulbs, you may want to consider replacing all at the same time in order to keep brightness and color equal (optional).
How do you push back rear disk brake piston on 2002 Mazda Protege?
The rear disc break pistons on Mazda are not to be pushed in. Instead you turn them in clockwise.
Where is the ignition coil on 2001 Mazda Protege?
The ignition coil is attached the cylinder 1. It's a metal box that the spark plug is attached to.
On the 2.0L engine, there are two coils mounted in the cylinder head atop the engine.
Where is the fuse for the dlc on a 99 Mazda Protege?
The 1999 Mazda Protege DLC fuse can be found in the fuse box. The DLC fuse will be at the bottom of the first column.
How do you replace the alternator belt on a 1997 Mazda Protege?
Turn the belt inside out. you need to get it under the power steering belt and to the other side of the pulley. You can use a crescent wrench to turn the pulley and get the belt under the other one. Turn the belt back right side out. loosen the alternator bolt and place the belt around the alternators pulley. Tighten the alternator bolt.
i am not sure why it does that but on the 97 it is the opposite it is simply a glitch in the wireing nothing to really worry about
My 97 did the same thing except it the bell worked on all the other doors except the driver door so my cousin took the little button sensor off the back door and rewired it to the front door and now it works like its supposed to.. he said that the driver one just got wore out.
What is a diagnostic code of P0134 mean for a Mazda?
Trouble code P0134 means:O2 sensor circuit no activity detected (Bank 1 Sensor 1)
