Oldsmobile Silhouette

One can purchase silhouette blinds in apparel stores. If the apparel stores do not have the silhouette blinds, one can possibly find the blinds in Halloween costume stores.

Only way i know of is to apply the parking brake before starting the vehicle.

I think you can turn off the headlights with the Twilight Sentinel switch. Turn it all the way down (or up) until it clicks.

The Illinois (IL) state sales tax rate is currently 6.25%. Depending on local municipalities, the total tax rate can be as high as 11%.

Intake manifold gasket leak....big problem with that engine. Sorry for the bad news.

your key for ignition is made for that specific computer in your car,i had to replace my whole steering column,the salvage yard told me the key coming with it would work..it didnt it kept telling me to clean the key,so i had to pop out the old ignition outa the old steering column and it started first time!

4.5 quarts with filter replacement. 4 quarts w/o.

Your 1999 Oldsmobile air conditioning air compressor can be found on the left-hand side of the engine. You can fill the system with Freon through the low pressure port.

Silhouettes are words from the French Minister of Finance, Etienne de Silhouette who admired the inexpensive quality of the hand-cut profile portraits which are difficult to master, and were less expensive than portraits in oils. Today, Cindi Harwood Rose, Pat Ramos, Vincent Torterra, Charles Burns, and Kathryn Flocken all do incredible free-hand silhouette portrait cuttings of profiles at stores and weddings.

Most modern GM vehicles have a transponder in the key that prevents the starter from engaging without it. To get a new key you need to get a factory key from your dealer or an aftermarket source, then program the vehicle to accept it. Instructions on programing are generally included with the new key.

start with replacing the switch first. check with your local junkyard first. they usually have these switches that are still good for cheap. a new motor is around 100 .

Turn the filter buy hand, then one quarter turn with the oil filter wrench. That's plenty. Make sure you put some new oil on the rubber gasket with your finger before screwing it on.

well, I'm glad I'm not the only one. I can't see it, i can barely get my hand in to feel around. tomorrow I'll find somebody to show me how to put the darn bulb in without having to disassemble half the car.

Just remove the headlight assembly above the turn signal/daylight running light in question. It will provide you with easy access.

that seems like the easy way to do this, but if you simply get under your Camaro unolt the first three bolts from the flap directly under where your head lights and turn signal lights are...then just stick your hand in there and wha la!

NO NO NO NO. It is very simple. Lift the front end enough to get comfortable access from underneath. Remove the access panel. Once you have noticed this, you will think you were an idiot.

No special tools, just a matter of squeezing nylon clips to release filter. One bolt holds the assembly in place. Just snap filter back onto fuel lines making sure the clip locks into the filter (should hear a click). Install bolt to secure filter back in place.

From underneath

this is called the lower switch

If you have an Advance Auto in your area, take it there and ask to use their computer scanner. You will probably have to do it yourself. It has step by step on screen directions, so it isn't hard to use. The Diagnostic plug in is under the dash, if you get about seat level you should be able to see it easily. They will probably ask for your driver's license so they know who you are in case you decide to steal it. To start using it you need to plug it into the Diagnostic plug under the dash, then turn the ignition to run (DO NOT start), that step allows the computer to communicate with the on board computer.

Haven't done it yet but it appears you can save some time by removing the windshield wiper motor and the overflow bottle on the passenger side of the engine compartment to gain access to pulling out the alternator. Other than getting it out of that cramped area its the usual process. Take tension off the belt and remove it off the pulley. Remove the 2 bolts holding it in place and position it to remove the wiring connectors. Then comes the hard part.

=== ===

24.5 gallons

After you open the hood the whole headlight assembly can be removed by taking off the the two black plastic wing nuts on top holding the headlight assembly in. There is also another wing nut like bolt that is between the headlight assembly and turn signal assembly that must be removed. One you do this you have to lift up on the headlight assembly to clear the threaded studs that the plastic wing nuts were on and pull both headlight and turn signal light assemblies straight out. They both have to come out together. There are some clips that still hold all of this in, but it will come out when you pull it straight forward. I have done this several times and it seems kind of tricky the first time, but actually is pretty easy.

If you don't want to purchase one, you can check one out for free at your local library. You can keep it for 3 weeks, and can renew it if you still need it.

Counter clock-wise

The 1997 Ford Explorer fuel gauge can be stuck on fault because the fuel float is malfunctioning in the fuel tank. The fuel gauge fuse might be blown.

call a ruud or rheem dealer with the serial number on the unit tag.They should be able to answer this.