Rover 400 Series

You need to remove the little drop down storage compartment which is situated just above the bonnet release on the drivers side near the ignition switch.

The stage 1 relay has blown! it is located behind the glovebox door above the heater blower. # find it # pull it out # replace it job done:-)

i got a 1100 Honda i use castrol brand part real-oil, part synthetic available

at my local aftermarket motorcycle store 10w40 year-round the castrol is

specifically made for motorcycles besides which /not car oil you buy at local

auto parts store/.1998honda aero v-twin 1100 c3.

It's the indicator of the trim level. Historical examples of these would have been:

G = Grand
D = Diesel
SE= Special Equipment
S = Either Sports, Super or Standard depending on manufacturer
L = lux
i = fuel injection

Example: Ford Sierra 2.0i GLS was a 2 litre, fuel injected Grand Luxury interior with 'sports' trim such as spot lights and front fog lamps when compared with the standard car.

However, as the trend for more letters and numbers on the back of cars grew many of the older naming conventions became obsolete.

SLi on a Rover 400 means two trim levels above the base model - all Rover 400's were fuel injected and the base model was just badged i. Then Si, SLi, GSi

To change the thermostat in a Rover 400 diesel 2.0L, first ensure the engine is cool and disconnect the battery. Drain the coolant from the radiator and remove the upper radiator hose connected to the thermostat housing. Unbolt the thermostat housing, take out the old thermostat, and clean the mating surfaces. Install the new thermostat, reassemble the housing, reconnect the hose, refill the coolant, and reconnect the battery.

Disabling the immobiliser system on a Rover 400 typically requires using the vehicle's key fob to disarm it or reprogramming the key. If the key fob is not functioning, you may need to consult the owner's manual for the specific reset procedure or seek assistance from a professional locksmith or dealership. Tampering with the immobiliser system can lead to potential security risks and may violate local laws, so it's important to proceed with caution.

To remove the dashboard from a Rover 400, start by disconnecting the battery to ensure safety. Next, remove any trim pieces and screws that secure the dashboard in place, typically found around the instrument cluster and along the edges. Carefully detach any wiring connections and sensors attached to the dashboard. Once everything is disconnected, gently pull the dashboard away from the mounting points, being cautious not to damage any clips or connectors.

To remove the starter solenoid on a 1998 Rover 420 diesel, first disconnect the negative battery terminal to ensure safety. Then, locate the solenoid, which is typically mounted on or near the starter motor. Disconnect the wiring harness and unscrew any mounting bolts securing the solenoid in place. Finally, carefully pull the solenoid off the starter and replace it with a new one if necessary.

To bleed the cooling system on a Rover 45, start by ensuring the engine is cool and the coolant reservoir is filled to the appropriate level. Then, locate the bleed screw, usually found on or near the thermostat housing, and loosen it slightly using a wrench. Start the engine and let it run until the coolant begins to flow steadily from the bleed screw without air bubbles, then tighten the screw. Finally, check the coolant level in the reservoir and top it off if necessary.

To get your Rover 416si key fob programmed, you can visit a local automotive locksmith or a dealership that specializes in Rover vehicles. Some independent automotive shops may also offer key fob programming services. Additionally, you can check online for mobile locksmiths who can come to your location to perform the programming. Always ensure that the service provider has experience with your specific vehicle model.

The Oil Rover 416 98 is a model of a specialized vehicle designed for oil exploration and extraction operations. It typically features robust construction to navigate challenging terrains and is equipped with advanced technology for drilling and monitoring oil fields. The model number often indicates specific configurations or upgrades, tailored for efficiency in oil recovery tasks. Such vehicles play a crucial role in the energy sector, enhancing productivity and safety in oil operations.

In a 2002 Rover 45 petrol 1600i, the fuel pump and fuel sender unit are located inside the fuel tank. To access them, you typically need to remove the rear seat and the fuel tank access panel, or in some cases, drop the fuel tank itself. The unit is a combined assembly that includes both the fuel pump and the sender for the fuel gauge. Always ensure to follow safety precautions when working with fuel systems.

If it was a head gasket then the compresion would be low in the affected cylinders low compresion as a result of wear wil make the car hard to start and overheating can also lead to electrical problems, Besides blowing a head gasket, overheating can also cause a cylinder head ro crack. Low compression and engine not starting or hard to start are symptoms. As mentioned above, do not discard the possibility of electrical problems due to overheating. However, the prime suspects are blown head gasket and/or cracked cylinder head.

Torque settings stage 1. 20 newton metres stage2. +180 degrees stage3. +180 degrees tightening order 9 5 1 3 7 10 6 2 4 8 bolts 7&8 are flywheel side of engine Mike 2

If your talking about the vertical alignment, there are setting screws on the back of the headlight assy. It looks like a 1/4" head bolt with a straight slot in in it and a 3/4" wide black or grey large serrated plastic washer under the head of the bolt. If you need dimensions then do a search on "www.siennaclub.org"

Upper front right portion of the engine.