Suzuki

Diagrams for a 2001 Suzuki Baleno engine is available in a few ways. One of the simplest requires a trip to a local auto parts store Local auto part stores offer consumer diagrams of their vehicles mechanical systems.

It would be close to 70km/h.

32:1 four ounces per gallon

they usually top out at about 65 mph

Use tire iron to break lugs loose. Jack up by frame to clear tire, remove lugs, exchange tire, thread lugs hand tight,lower until tire just contacts ground to keep from spinning, torque to specs, drop car.

Yes, they are exactly the same.

oil should be changed every 3 months or 3,000 miles which ever comes first

Underneath and just about in the middle of the skid plate. There should be a hole in the skid plate so you can get at it. Hope that helps

Sounds like you've got worn out syncros on the 5th gear. ~ Tim ~

There is no separate transmission oil on the Ozark. The engine and the transmission and the clutches are all lubricated by the oil you put in the engine. That's why it is smart to use the upgraded motorcycle oil they sell at the dealer. Its supposed to work better in transmission than regular oil. There is some 90W oil in the rear differential that is located back on the rear axle that needs checked and changed - but not very often. Look at your manual.

i will send you a CD rom with full srad manual

Stuck choke or bad petcock.

The tenth digit of the vin. A=80,B=81,C=82,D-H=83-87,J-N=88-92,P=93,R=94,S=95,T=96,V=97,W=98. I work on and own 78-99, so i know these letter number id's, from these higher, I'm not sure. You would have to call a dealer.

Mostly Clarion, like the radios

intake .004mm , exhaus .006mm

A 17 inch alloy wheel with a low profile tire will not fit the Suzuki Swift model India, you will need a 15 inch wheel.

Elementary through middle school.

I have a 2001 250 quad runner. I just finished changing my oil. You must jack up the rear end of the ATV and put jack stands underneath to supportit. Remove the back right tire. The oil drain plug is is underneath the engine on the right side and requires a 14mm socket for removal. Remove plug and let drain. The filter is behind a cover that is retained by 3 bolts in a triangle pattern that require a 10mm socket for removal. After drainage, replace the filter, cover, retaining bolts/nuts, and drain plug. Refill with the manufacturer recommended oil and replace the tire.

I have a 2001 250 quad runner. I just finished changing my oil. You must jack up the rear end of the ATV and put jack stands underneath to supportit. Remove the back right tire. The oil drain plug is is underneath the engine on the right side and requires a 14mm socket for removal. Remove plug and let drain. The filter is behind a cover that is retained by 3 bolts in a triangle pattern that require a 10mm socket for removal. After drainage, replace the filter, cover, retaining bolts/nuts, and drain plug. Refill with the manufacturer recommended oil and replace the tire.

remove the cover on the front sprocket. Loosen the locking bolt. then sqwueeze your clutch lever in and push the lead stop out of the handle. and out of the bike. its really that simple putting the new one in same steps just tighten the nut until you feel resistance and reduce 1/4 turn and fine adjustments can be made on the lever mount.

The fuse panel is under the cover above the kick stand

on the left side

The serial number is on the left side of the frame right behind the radiator. You may need to clean the dust off the frame to see it considering it is stamped into the frame.

for me the best combination sprocket for rider 150 15/42 kung high speed kailangan mo at kung pang long distance na biyahe.

the top speed if stock is 47 mph

The drain plug on my 06 vinson is 17mm, I would guess they haven't changed since 03. Hope this helps.

Rear wheel bearing nut tork setting