0
Tractors and Farm Equipment
Tractors are machines designed for hauling and are primarily used in construction or agriculture. They are classified as farm equipment together with ploughs, harrows, combines, mowers, balers, and pickup trucks.
4,777 Questions
Who invented the case ih tractor?
It was founded by Jerome Increase Case in 1842. The first tractor (powered by steam) was built in 1869 and their first traction engine was built in 1876.
How do you test a tractor starter that does not spin?
Start by checking the selenoid switch - you take a heavy wire or screwdriver and put across the two main connections for the main wire and if it doesn't turn over then, try putting the booster cables from a good battery - put ground on the body of the starter and the positive on the post where the wire is hooked on, if it doesn't turn over then your brushes maybe bad or if someone has hit it with a hammer or hard object you may have smashed the magnets inside it. In which case you will have to get new magnets, brushes or a new starter.
On an air brake system what do you do when the low psi warning light comes on?
if low PSI warning comes on, you need to get vehicle off the road. low PSI means u have low air, or an air leak. this also means you are going to run out of air that operates the brakes
when this happens, the brakes lock on and you ain't going anywhere
warning will come on with enough time to get vehicle to side of road
if you drive a 379 pete and the warning is on and your psi is normal. check the low air switches they are behind the pannel in front of the clutch and brake pedal they are usually corroded
AnswerIt depends on WHEN the low PSI warning light came on.
If I was driving and the light came on, that means one of two things: I've got a massive leak somewhere in the air system and it just happened, or the belt to the air compressor broke AND I've got a leak in the system. In either case, pull over before your spring brakes activate. Those will stop you, but they won't turn the brake lights on so there's a chance you'll get rear-ended. Once you're stopped, shut down, get out and listen for the hissing sound. (Most people who get this light while driving ran over a recap, so try to dodge those, okay?)
If it came on while I'm backing into a really complex hole that needs a lot of braking, that's normal. I'd just put the truck in neutral and rev it up a little to build some pressure in the brake system.
Your best bet would be to get in touch with a local diesel fuel injection repair shop that has a Bosch dealership and give them that info. Go onto the Bosch web site and look world wide there for an authorized dealer.
How do you thread a Ford 542 hay baler?
fisrt you need to get a ford baler I recomend looking at aution fliers in the Midwest [much more time comsumeing then eBay] If this step takes long enough you may never have to make hay just keep going to auctions. Once you have the baler you will need to have a tractor to power it I recomend inheriting one from your gampa or pa if this is not possible you will probably have to borrow one, as a last resort buy one . Next make sure you have twine loaded in the twine bin wich is located at the rear of the baler [the door that opens up] you will need two bales rolls of twine one for each side of the bale. As you stand behind this compartment look to the lower left side you will see two clamps held in place with a wingnut over a tensioner spring behind this is the hole the twine goes thru loop the twine thru the loosened tensioner and let it fall through the hole so it hangs below the compartment towards the ground. At this point it helps to have a partner I recomend having one of your children help you, that way they will know how to thread a ford baler it will also give them the chance to increase their vocbulary of words not to us in school. If you don't have a helper don't give up! Crawl under the baler [wait] befor you can finish this the baler has to be hooked up to the tractor draw bar and the PTO shaft needs to be hooked up be sure all guards are in place. Now slide gently under the twine compartment to where you have pushed the twine thru the hole pull out 3 or 4 feet of twine you partner at this time should make sure the twine doesn,t tangle uo in the compartment front hole is for left side of bale rear whole is for right side , also when you put the spools of twine in be sure the twine spools out the center and up thru the top of the spool. If as you lay under the baler pulling out the twine thru these holes it should come out freely if it doesn,t tell the kid to give you some slack. Now as you look to the left side of the baler you will see two arch shaped thick pieces of steel called the needles depending on wich part of the rotation the baler stoped moveing at you mabe able to see the front part of them for as the baler cycles they will come all the way free of the bottom of the baler if you can see the front of the needles you will notice a hole in the front of each if the front of the needles are not visible you will need to cycle the baler by turning the flywheel do this manualy and have the kid watch and tell you when the front of the needles come free of the bottom of the baler now thread the twine thru the whole in the front of the needles left twine for left side right for right pull several feet of twine thru and let it lay on the ground, Now if you don't have a windrow of hay ready to bale this process cannot be completed if you do however you may tighten up the wingnuts over the tensioner springs until the twine pulls free but without free spooling it does need some tension. The baler now needs to be brought up to the windrow of hay and engauged let it start making a bale the first one wont tie but it will bring the twine up to the knotter wich are on top of the bale compressing area opposite the bottom where the needles are basically at this point if all is working correctly the second bale will tie perfectly as the needles feed the twine the knotters wich self feed . Then you are done if the second bale doent tie sqirt some wd40 on the knotters and adjust the bale knotter timing so you are making very small bales and run thru a fairly good piece of windrow even if it doesnt tie correctly rite away keep going for a while it may loosen up a stuck knotter and start working .
be sure you gease all the zerk before you start
when operating an electric pallet jack before entering a trailer that is not attached to a tractor always make sure that
answer it
Where can you buy lawn garden tractors?
Big box hardware stores often carry lawn garden tractors from big name companies. Home Depot carries John Deere and Ariens brand tractors. Sears carries Craftsman brand tractors. You could also try a local feed store or check the craiglist ads for used models.
Where can you find which construction equipment manufacturers use Mitsubishi engines?
contact shin caterpillar company whom would be the one who supplies the Mitsubishi engines, go through the company listing of products as supplied to other manufactures and you should be able to track where and what they were supplied for in the way of equipment.
Visit http://www.diamonddiesels.co.UK/engref.HTML where you will find references and links to the various Mitsubishi engine types that are used by construction equipment manufacturers
Can you have recap tires on a steering axle of a truck?
Lawfully.... No !!!
How many times while driving on a highway have you seen peices of a tire strewn on the pavement? That's from a rear tire and even then would be difficult to control the vehicle in a safe manner to the shoulder and stop. Think what would happen if it occurred on a steering tire? Hello ??!, steering tire ! does that raise any questions or ideas ?
Better check your DOT manal, you can run recaps on anything but the steers of a bus...
Cranes live in Asia, East Asia, and West Asia, mostly. But they also live in America, South America, Europe, and Africa. They are also scattered around the world, They are also threatned.
Where can you find an oil tank for a stihl ms 310?
An oil tank for a Stihl MS310 can be bought directly from Stihl dealers. Alternatively, there are specialty shops online that sell chainsaw parts.
