answersLogoWhite

0

🚗

Cadillac DeVille

This category covers questions about the Cadillac DeVille, a full-size luxury sedan manufactured by General Motors and sold through its Cadillac division. The DeVille was produced from 1949-2005 and was succeeded by the Cadillac DTS.

3,166 Questions

What is the ac pressure supposed to be on a 88 cadillack deville?

have to get a chart. It all depends on ambient temperature. High pressures can range from 150 psi to 300 psi depending on ambient

Where would you find a material which is a resistor?

Where would you find a material which is a resistor?

You can find a resistor material in Europe

What could cause the low oil light to come on when the car is idling?

AnswerIf the engine is idling very low - oil pump may not generate enough pressure, causing light to come on. Make sure you have adequate oil, and that idle speed is correct. If this does not correct, possibly oil pump screen dirty

It could also be the oil sensor is bad or leaking. This happened in my 1996 Chevy Corsica. I thought it was the oil pump, but it turned out to be just the sensor that needed to be replaced.

When was C.C. DeVille born?

C.C. DeVille was born on 1962-05-14.

What causes a 1991 Tord Taurus S H O to just cut off while driving?

The cause for a 1991 Ford Taurus to just cut off while driving is probably a problem with the computer. If the car will start again after about 90 minutes, then check the computer module for code errors.

What causes banging engine noise when accelerating?

The most probable cause is poor fuel or water in your fuel. This could also be due to the timing being out of proper adjustment.

What is the firing order for a 1987 cadillac deville 4.9L?

The firing order for your 1987 Cadillac Deville 4.9 liter engine is one, eight, seven, two, three, six, four, five. The firing order can be found in the back of the owners manual.

Where is the oxygen sensor located on a 1995 cadillac deville 4.9L?

Today is your lucky day, I just changed both of my oxygen sensors on the same year and motor. The first one is located directly on the exhaust manifold in front of radiator as you open your hood on the car look straight down and you will see it. The other sensor is a little more difficult to find by looking straight in the engine. The second sensor is located near the firewall on the exhaust manifold. The only problem is, you have to get underneath the car to remove the sensor. Just follow your converter directly toward the engine intake manifold and you will see it, make sure you have a flashlight, regardless of how much daylight is outside. Once I got under the car a found it, it was easy to come off and replace. Good luck! rljenkins66@aol.com

Where is left bank on a 98 deville?

On a 1998 Cadillac DeVille, the left bank refers to the set of cylinders on the driver's side of the engine. In a V8 engine configuration, this typically includes cylinders 1, 3, 5, and 7. If you're looking for specific components or parts related to the left bank, such as the fuel injector or spark plugs, they will be located on that side of the engine.

Where is the EGR on Cadillac Deville 4.9L?

behind the air filter more towards the throttle body. kind of near the sticker that says 4.9 Liter. look above that. and remember, the egr almost looks like a flying saucer

Where is the bleeder valve for the air pockets in the cooling system of a 1996 Cadillac DeVille Concours?

Just keep the reservoir filled to the right line and the cooling system should take care of the air bubbles after a while, provided that the radiator cap is sealed for both pressure AND vacuum.

Are after-market oxygen sensors as good as Factory?

on some vehicles the universal aftermarkets are ok to use, however on dodge, Chrysler and jeep vehicles they don't work the cel will cme back on the dealer part in this case is actually better.

How do you find out if the idle control unit needs to be replaced?

The newer vehicles with computers do not allow for idle speed adjustment. If yours is one of those vehicles, you will not be able to adjust the idle speed. On the other hand, if the idle speed is very high on one of those vehicles it could be that the engine could have a vacuum leak.

Where is the ecm on a 1993 deville?

The ECM on my 93 Deville is located inside passenger cabin, on passenger side, behind dash under the glove box against the firewall. It is held in place by a single 9/32 nut on the bottom of unit. This unit can be replaced with very little difficulty and no removal of any other parts.

How do you replace the heater core on a 1996 Cadillac Deville?

how do you change the heater core on a 99 cadillac deville? I need to know, "Kaiser."

How do you replace the water pump on a 1988 Cadillac DeVille?

replacing the water pump on the deville is no easy task if you can avoid doing it yourself take that option it is an aluminum block that the water pump is bolted to when you take the housing and screws off its a pain to get them back go to a trusted pro labor is around 350 but water pump is enexpensive

Can 22 inches fit 99 deville?

Yes 22 inches can fit your 99 deville. If your rim size are 22 x 8 or 8.5 all you have to do is buy you some spring spacers which you can get from any auto parts store. I have a 2000 deville with 22 x 8 on it and I have a cousin with a 99 deville that has 22s on it.

Will 24's fit on a Bonneville without lifting it?

no. you have to lift it and cut it. if its the older style like a 92-99 you'll have to cut the buper and roll the fender. if its the newer bonneville you'll have to cut inside the wheel well and take out the plastic in the wheel well. GOOD LUCK you'll need it!

How do you drain radiator on a 97 Mazda Millenia?

Draining the radiator

You would remove the radiator cap to ensure smooth flow.

Put a pan or bucket under the radiator to catch the coolant. Please make sure you don't spill any, or clean it up if you do. Antifreeze tastes sweet. Cats, dogs and other animals are very attracted to it. It is fatal when they drink it. For us too.

There should be some kind of a draincock at the bottom of the radiator. Open it to drain the coolant. Flat pliers or similar tool might help opening the draincock if it is stuck, but be very careful not to break it. They are made of plastic and can become crisp with age.

If the draincock doesn't seem to open (or you might break it), you could, as a last and rather messy resort, open the clamp around the lower radiator hose and hope that the entire content of the cooling system doesn't escape all at once. Have a wide bucket ready!

Be aware, you cannot the drain the radiator without draining the entire cooling system because it's all connected. When you refill the system, please follow the procedures as described in the answer to "How do you bleed the coolant for a 1998 Mazda Millenia?" This will avoid bad and costly surprises with an incompletely filled cooling system.

on the millenia, the drain is on the passenger side of the radiator. you have to look from underneath, you will see an access hole in the splash shield. a large Phillips screwdriver is used to loosen/remove the drain plug.

What causes a Cadillac run hot?

what model,year,size motor is the caddy you are talking about? I can't give you a competent answer w/o this info. General things to ck. are: thermostat, rad. fluid level(DO NOT CK. WHEN HOT!),Rad. blockage. Other than that, I need more info. Tony

Its a 1996 Cadillac SLS Northstar

How do remove the heater core from a 1996 cadillac sedan deville?

Notes

  1. Disconnect battery ground cable.
  2. Remove glove box attaching screws, then the glove box.
  3. Remove lower sound insulator attaching screws and nuts, then the lower sound insulator.
Heater And A/C Programmer And Actuators



  1. Remove programmer as follows:
  1. Remove programmer shield attaching screws, then the programmer shield.
  2. Disconnect threaded rod from programmer.
  3. Disconnect programmer electrical and vacuum connector, then remove programmer.
  1. Disconnect body control module electrical connector, then remove module attaching screws and module.
  2. Remove relay panel from module assembly, then the module assembly heater core cover.
  3. Disconnect heater hoses from heater core.
  4. Remove two heater core attaching screws, then the heater core.
  5. Reverse procedure to install.