Car Stereos and Speakers

The size of speakers can vary widely depending on the type and model. Common sizes for bookshelf speakers typically range from 4 to 8 inches in woofer diameter, while floor-standing speakers can have woofers from 6 to 15 inches or more. Subwoofers usually range from 8 to 18 inches. For specific measurements, it's best to refer to the manufacturer's specifications.

To power two subs rated at 700 watts RMS each, you'll need an amplifier that can deliver at least 1400 watts RMS total (700 watts RMS per sub). It's generally recommended to have an amp that provides a little more power than the combined RMS rating for headroom, so an amp rated around 1600 to 1800 watts RMS at the appropriate impedance (likely 2 ohms or 4 ohms, depending on how the subs are wired) would be ideal. Ensure the amp's output matches the impedance of your subs for optimal performance.

Yes, you can power two 12-inch Kicker Comp subwoofers with a JBL GTO3501 amplifier, provided the subwoofers' impedance matches the amplifier's output. The GTO3501 is capable of delivering up to 350 watts RMS at 2 ohms, which should be sufficient for the Kicker subwoofers, as long as they are wired correctly (typically in parallel for dual 4-ohm subs). Make sure to check the power handling specifications of your specific Kicker model to avoid overloading the subwoofers.

To change the factory stereo in a 2000 Vectra, first, disconnect the car battery to ensure safety. Remove the trim panel around the stereo using a trim removal tool, then unscrew the stereo from its mounting bracket. Disconnect the wiring harness and antenna from the back of the factory stereo. Finally, connect the new stereo using the appropriate wiring harness adapter, secure it in place, and reattach the trim panel before reconnecting the battery.

To remove the rear deck cover of a 2001 Oldsmobile Intrigue for speaker replacement, start by removing any visible screws or fasteners securing the cover, typically located near the edges. Carefully detach any clips holding the cover in place by gently prying it up with a trim tool or flathead screwdriver. You may also need to remove the rear seatback or seat cushion for better access. Once loose, lift the rear deck cover away to access the speakers beneath.

To replace 6x9 speakers with 6x8 speakers, first, remove the existing 6x9 speakers by unscrewing them from the mounting location and disconnecting the wiring. Next, prepare the installation area for the 6x8 speakers, which may require an adapter plate to ensure a proper fit, as the dimensions differ. Connect the wiring from the vehicle to the new 6x8 speakers, ensuring correct polarity. Finally, secure the new speakers in place and test them to ensure proper functionality.

Yes, it's generally acceptable to have 12 volts on the remote wire to your amplifier. This wire is designed to send a signal from your head unit to the amp, telling it to turn on when the car is powered. A voltage reading around 12 volts indicates that the remote wire is functioning correctly. However, ensure that the voltage remains stable and does not exceed 12 volts significantly, as this could indicate an issue.

To fix squeaky speakers, first check the connections to ensure they are secure and free of corrosion. If the problem persists, inspect the speaker drivers for any visible damage or debris that may interfere with sound quality. You can try tightening any loose screws and adding a small amount of lubricant to moving parts, like the speaker cone or suspension, if applicable. If these steps don't resolve the issue, consider seeking professional repair or replacing the speakers.

The Pioneer KEH-P4800 stereo typically mounts into a vehicle's dashboard using a standard DIN or double-DIN installation method. First, you would remove the existing stereo, then connect the wiring harness adapter to the car's wiring and the stereo's connectors. After securing the stereo in place with mounting brackets or screws, you can attach the trim ring to finish the installation. Finally, ensure the unit is properly powered and test its functionality before reassembling the dashboard.

The factory speakers in a 2008 Hyundai Tiburon are typically 6.5 inches in diameter for the front doors and 6.5 inches for the rear. Depending on the audio system option, the rear may also feature a pair of tweeters. Upgrading to aftermarket speakers may enhance sound quality and performance if desired.

The bolt size for a 6x9 speaker typically varies depending on the specific model and manufacturer, but most commonly, they use 8-32 or M5 bolts. The length of the bolts can also differ, usually ranging from 1 to 1.5 inches. It's advisable to consult the speaker's installation manual or specifications for exact measurements.

Speakers were developed through the contributions of various inventors and engineers over time. Early advancements in loudspeaker technology can be attributed to figures like Johann Philipp Reis, who created a primitive version in the 1860s, and later, Thomas Edison and Emile Berliner, who further advanced sound reproduction. The modern dynamic speaker design, which utilizes a voice coil and magnet, was perfected by engineers like Edward W. Kellogg and Chester W. Rice in the 1920s. Today, numerous companies and innovators continue to produce and enhance speaker technology.

The MG ZT typically features 6.5-inch speakers in the front doors. The rear speakers are usually 6-inch models. However, specifications can vary slightly depending on the specific model year and audio system option.

You can purchase a harness for the JVC KD-SC601 stereo at various electronics retailers, both online and in physical stores. Websites like Amazon, eBay, and Best Buy typically carry compatible wiring harnesses. Additionally, car audio specialty shops may also have the harness available for purchase. Always ensure to check compatibility before buying.

To reset your JVC car stereo, locate the reset button, which is usually a small pinhole on the front panel. Use a paperclip or a similar object to press and hold the button for a few seconds. If your model doesn't have a reset button, you can also try disconnecting the car battery for a few minutes to reset the stereo. After the reset, you may need to reprogram your settings and presets.

You can determine if your subwoofer is broken by checking for a lack of sound output, even when it's powered on and connected correctly. Listen for distortion or unusual noises when it’s functioning, which may indicate damage. Additionally, inspect for physical damage, such as tears in the speaker cone or a burnt smell, and test it with different audio sources to rule out issues with other equipment. If it still doesn't work, it may require repair or replacement.

For a 2013 Chevy Malibu, the stereo wiring colors are generally as follows: the constant power wire is usually red, the ignition power wire is typically yellow, the ground wire is black, and the speakers have various colors—front left (+) is white, front left (-) is gray, front right (+) is purple, and rear speakers follow similar color coding. Always consult a wiring diagram specific to your vehicle for accuracy, as wiring colors can vary based on the trim level and audio system.

The ohms rating on a speaker indicates its impedance, which is the resistance the speaker presents to the electrical current from an amplifier. Common ratings for home speakers are typically 4, 6, or 8 ohms. A lower impedance generally allows for more current flow, potentially resulting in higher power output, but it also requires a compatible amplifier to prevent damage. Matching the speaker's impedance with the amplifier's specifications is crucial for optimal performance and safety.

The stock speakers in a 2008 Saturn Vue typically include 6.5-inch speakers in the front doors and 6.5-inch speakers in the rear doors. Some models may also feature a subwoofer, which is usually located in the rear cargo area. If you're considering upgrades, it's important to verify the specific audio system in your vehicle, as configurations can vary.

The bass Q factor on a Clarion CD player refers to a setting that allows users to adjust the quality and intensity of the bass response in the audio output. A higher Q factor typically results in a more pronounced and focused bass sound, while a lower Q factor provides a broader and softer bass response. This feature enables users to customize their listening experience based on personal preferences or the acoustics of the environment. Adjusting the bass Q factor helps enhance overall sound quality and balance in the audio.

The wiring code for a Delco radio with the model number 10324040 typically includes a color-coded pinout for connection. Commonly, you will find wires for power (usually red for ignition and yellow for constant), ground (black), and speaker outputs (various colors for front and rear speakers). For precise wiring, refer to the specific wiring diagram associated with your vehicle's model, as configurations may vary. Always ensure to disconnect the battery before making any connections.

To reset a JVC LT-46N700 TV, first, turn off the TV and unplug it from the power outlet. Wait for about 1-2 minutes, then plug it back in. Turn on the TV, and if you want to perform a factory reset, navigate to the menu, select "Settings," then "Reset," and follow the on-screen prompts to complete the process. Always refer to the user manual for specific instructions tailored to your model.

If your stereo head unit already has a built-in fuse, you typically do not need to add an additional inline fuse. However, it's a good practice to include an inline fuse on the power wire if the wire runs a significant distance or if it's not protected by a fuse box, as this can help protect the wiring and prevent potential fire hazards. Always consult the manufacturer's recommendations for specific guidance.

In a Chrysler Sebring, the common color codes for speaker wires are typically as follows: the positive wire is often white or gray, while the negative wire is usually black or green. However, it’s essential to verify with the specific model year and audio system, as variations may exist. For accurate wiring, consulting the vehicle’s service manual or a wiring diagram is recommended.

The front speakers in a Jeep CJ7 are typically secured with 5/16-inch nuts. It's a good idea to check your specific model, as variations may exist based on the year or aftermarket modifications. When replacing or reinstalling, ensure you use the correct size to avoid damaging the speaker or mounting area.