Chevy Camaro RS

If its a Z28 the difference is a nonvented opti spark VS a vented optispark of course this doesnt include the countless number of option combinations like TTops, power windows/locks A/C stuff like that.... if its a V6 the 94-95s are 3.4L but in late 95 they swapped over to 3.8L 95 3.8L are rare

200 hp but if you add an exauhst system you will gain like 10 hp and a k&n cold intake system some extra 15 hp . Talking around 230 hp stimated depending on octanage boost of the gasoline .

Insurance depends mostly on the driver (gender, age, number of claims you have, driving record, safe driver training). Specifically, camaros are priced lower than imports so they will be lower to insure vs non-domestics of the same type (muscle/pony type cars). If you upgrade packages from the base model (i.e. V6 non RS), the insurance premium goes up because these parts increase the repair cost of the vehicle should it become damaged. Insurance premiums are all risk-assessment based fees.

No

195 - 220 Degrees [F]

1, 6, 5, 4, 3, 2.

It's being built in Canada, I forget which town.

Just take all the bolts out of the pan and it will come off, sometimes the pan might stick a little but you can put a screwdriver in between the pan and tranny and pry a little and it will come down, be sure to have a large pan handy as about 4 or 5 qts. of fluid will come flying out.

As long as you have the electric pump in the gas tank your fine.

In order of MY observations: connections, hoses, power steering pump and finally rack or steering gear, although rack is becomming much more common.

It is illegal to disable the driver airbag, and also a very ignorant thing to do. Disable that airbag and have an accident where you are injured, and your insurance company could refuse payment for the injuries you may suffer. Air bags save lives and I will not help you on this one.

Get the Haynes repair manual for 1982 thru 1992 Camaros.

9 to 13 psi is ideal for tbi engine with a few light modifications such as upgraded holley tbi and free flow breather

Any small block or big block Chevy from the late 60s through the end of that block style around 2000. A 4.3 V6 should bolt up in there too, and maybe the 2.8 and maybe even the 3.8.

They were the exact same wheel, so yes

youve got to be more specific.

Depends on the year. The SS started in 96. 96 and 97 had an LT1 V8 with the old style block. 98 through 02 have the LS1 V8 engine. I think 2009 or 2010 is the next year of Camaro, and they all have LS style V8 engines through the present.

I rebuilt my 231 (3800 series II, 3.8) chevy.

I checked the bearing clearances several times, and primed the engine before starting it the first time.

the current pressure I am seeing is about 70-80 cold and 45-60 at operating temperature.

if you are seeing anything lower than 30, it is likely time for a rebuild. the oil pumps on these engines are crank driven and there is no such thing (for these) as a high pressure pump.

Usually fuel pumps are located in the gas tank.

15in are what came stock but 16s aren't uncommon.

It should be on the big rubber hose that goes from the airbox and hooks to the throttle body.

Explain what's happening with the car's fan a little better. When driving the car its ok, when I am in traffic for 15 minutes and over the temp, starts to rise.If I put the ac on, IN traffic, it over heats.

Need to know the year and engine size.

When I replaced my fuel pump, the gas gauge would only show a 1/4 of a tank when I filled it up, turns out the guys at auto zone sold me the wrong one, so wherever you got yours from, you might want to check to make sure it's the right one, other than that I have no idea

first open trunk. lol then look at the back of car inside of trunk & youll see carpet that goes to latch area of car. it is mostly held down by tar seal, or plastic buttons. if no buttons, its just held by tar stuff! pull away from back of trunk gently. youl see about 8 - 10 plastic screw nuts. remove them and the light section comes off! the whole back of car light assembly. find burned out bulb & replace. the light bulb part has to be pressesd & turned to remove. make sure that you use the same style light too! some are turn/stop some are 1 function.