0
Chrysler Cirrus
Chrysler Cirrus was a four-door midsize sedan manufactured by Chrysler Corporation from 1995 to 2000. This vehicle featured aluminum wheels, optional rear child seat anchorages, and an 8-speaker AM/FM cassette stereo as standard.
548 Questions
How do you change a water pump on a Chrysler Cirrus?
It is fairly difficult to change a water pump on a Chrysler Cirrus. First, you remove the crankshaft pulley, remove one engine mount, take off the timing belt, and finally gain access to the pump. You can then feel free to switch them out.
Where is the camshaft sensor position located on a 2000 Chrysler cirrus?
Four cylinder, it is on the driver side end of the head. Six cylinder, it is inside the distributor.
Where to locate and replace a speed sensor on a 1999 Chrysler Cirrus engine?
The Speed Sensor (for 2.5 V-6) is located in the Transmission housing Drivers side behind the Dipstick Oil tube under the Distributor (hard to see!), you must remove the tube in order to access the sensor or replace it. It is a Cylindrical sensor with a tab on it for screwing it to the transmission, screw holding it is a 10mm.
How can you disable the factory alarm on a 1997 Chrysler cirrus?
The alarm is part of the programming of the BCM and can not be removed
Where is the ingition coil located on a 1999 Chrysler cirrus?
Four cylinder, it is on top of the valve cover.
Six cylinder, it is inside the distributor.
How do you replace spark plugs 2000 Chrysler cirrus 2.5L?
You have to remove the upper intake manifold.
Where are the spark plugs on a 2000 Chrysler Cirrus?
They are located through the center of the valve cover.
They are located through the center of the valve cover.
How Do you replace the transmission modulator valve on 1998 Chrysler cirrus?
This transmission does not have a modulator valve.
This transmission does not have a modulator valve.
What would make my 1996 Chrysler cirrus overheat and blow cold air?
low coolant level check for leak and repair add new coolant and burp the system to get all the air out and make sure thermostat is working properly
Where is the mode door motor on the car 1996 cirrus lxi?
in the heater box. problem is most likely the cable or the retainer on th switch came off. if the knob is stuck or really hard to turn it is the door or frozen cable. if it is really loose the cable is boken or clip fell off. if it moves a little then jams the cable is kinked.
Where is the fuel pump relay on a 1997 Chrysler cirrus?
inside the power distribution center located under the hood next to ecm and air filter box. remove black cover and look at inside of top cover it will tell you the location of the relay on mine it is all the way to left of the distribution center and the second relay from front to back.
Where is the blower motor resistor located on a 2000 Chrysler cirrus?
Underneath the passenger side dash.if you look under there you will see a plastic cover that is held in with 2 or 3 plastic clips,remove the clips and the plastic piece,you will see the resistor it is only held in with 2 screws,and it can be removed fairly easy.
Where is the coolant bleed screw on a 2000 Chrysler 300M?
It is hidden on the intake near where the upper radiator hose attaches.
Do you need to replace the timing chain on a Chrysler cirrus 2.5L?
The 2.5L in a Cirrus has a timing belt, and yes it should be replaced around 100,000 miles.
What does it mean when the check engine light blinks rapidly in your 96 Chrysler Cirrus Lxi?
A fast flashing check engine light is an indication of a running issue that is causing severe emmisions and catalytic converter damage. The normal cause is a harsh misfire. If you have it checked for codes, it should tell you which cylinder is the problem.
Where is the thermostat located on your 1998 Chrysler Cirrus LXI model with a 2.5L V6 engine?
It is under the housing where the lower radiator hose hooks to the engine.
What happens if you add to much oil to your car?
you may need a new car....... the old one will be in a junkyard, because it exploded.
Brakes are adjusted too tight. Brakes are misassembled. Brake hose is restricted, holdings the brake on.
How do you replace rear main seal for Chrysler 2.7?
You remove the transmission, and the flexplate(flywheel) to access the rear main seal.
