Dodge Ram

First let headlights cool down if they have been on. Open hood. The back of each headlight has a blue plug. Remove blue plug then turn gray ring 1/4 turn counterclockwise to unlock the bulb. Pull bulb and insert new bulb. Bulb goes in with flat side up. CAUTION: Wear eye protection and gloves because bulbs can explode. Avoid touching the glass area of the bulb. Reverse removal process to install.

Yes they will fit but if you crank the steering all the way you rub a little depending on the tire tread.

120-150 psi

If it is like my Ford Explorer , the check gage light comes on if the engine coolant temperature is high , the engine oil pressure is low , or the fuel level is near empty

Dodge equips your vehicle with more than one possible size during production. The correct size should be listed on the driver's door post, somewhere else on the vehicle, or in your owner's manual. The sizes installed were. 245/70-17 265/70-17 275/60-20 If you have 20" wheels you now know the correct size. If you have 17" wheels you have 2 choices. What size is on the vehicle now? If they are the OEM tires then they are the correct size. All this is based on the truck being a 2 WD.

The side with cylinder #2, the pass side.

-------------------------------------------------------------------------------- 4.2L, 4.6L, 5.4L and 6.8L Engines 1. Disconnect the negative battery cable. 2. Remove the vacuum hose from the EGR valve. 3. On the 4.6L engine, remove the nut and brake booster bracket. 4. On the 5.4L engine, remove the DPFE sensor retaining nuts and place the sensor to the side to allow access to the EGR tube. 5. Disconnect the EGR valve-to-exhaust manifold tube from the EGR valve. 6. Remove the EGR valve mounting bolts, then separate the valve from the intake manifold. 7. Remove and discard the old EGR valve gasket, and clean the gasket mating surfaces on the valve and the intake manifold. To Install: 8. Install the EGR valve, along with a new gasket, on the manifold, then install and tighten the mounting bolts. 9. Connect the EGR valve-to-exhaust manifold tube to the valve, then tighten the tube nut to 25-35 lbs. (34-47 Nm). 10. Connect the vacuum hose to the EGR valve. 11. On the 5.7L engine, install the DPFE sensor. 12. On the 4.6L engine install the brake booster bracket and the retaining nut. 13. Connect the negative battery cable.

the switch is on the door panel approx four inches from the window, this is the only switch that sends power to the window regulator motor (window motor).

Start out by checking that the blower has both power and ground and if so then next check the a/c - heater controller...........

For the 2010 model year it is rated at 10,450 lb .

5w20

The lift pump is on the lower driver side of the block. The injection pump is on the front driver side of the block.

just purchasedmine and am getting 18 hauling 5K pounds and 21 mpg highway unloaded, both in windy weather. guartanteed to get better once i get 3k-4k mi on it :)

No. The current Hemi engines are 5.7, 6.2, and 6.4L.

Gas engine is inside the fuel tank. Diesel is on the driver side of the engine.

The manufacturer was able to meet the tail pipe emission requirement without EGR through timing and fuel control.

The manufacturer was able to meet the tail pipe emission requirement without EGR through timing and fuel control.

Depends on the year. They started at about 175 in 1989 and went as high as 350 in 2006.

Depends on the year. They started at about 175 in 1989 and went as high as 350 in 2006.

That all depends on the size of the tire, Is it a 36x12.5R16? If so than it will probably fit, you might want to go with a 16x9.5 inch rim or a 16x10, the R size will tell you the height of rim it's designed for.

Remove the wiring harness from the back of your 1996 Dodge Ram 1500 alternator. Remove the belt from the alternator. Remove the alternator retaining bolts. Reverse the process to install your new alternator.

i dont no

try looking around where the oil filter is that may be it.

That's funny, but I believe it is screwed right into your oil filter adapter. (Housing) So crawl under her, locate the oil filter and you should see the wire for it. Disconnect the connector and unscrew the sender/switch/sensor. Ummm you may want to change your filter and oil while you are at it, oil will most likly spill out, so atleast have pan ready. Good Luck

The oil pan on a Dodge Ram 1500 with a 5.9L engine is removed by draining the oil, removing the retaining bolts, and lowering the pan from the vehicle. The gasket material will create a strong seal which must be broken before removal.

That is the downstream O2 senosr and it located after the catalytic converter on the passenger side

Yes. Your best bet is to get an axle out of a dually from the same year. If you can get the drive shaft and springs as well. Many 2500's have a Dana 70, while the 3500 has a Dana 80. This will make your drive shaft too long. We just did this and found out the hard way. You will also need an extension on the parking brake cable. The dually fenders are just a bolt on part.

Spark plug, plug wire, injector, distributor cap, rotor, internal engine failure,.....