0
Dodge Ram
The Dodge Ram is a large pick-up truck produced by Chrysler from 1981 to present. The car, which features a front engine and rear/four-wheel drive, was named “Truck of the Year” three times by the Motor Trend magazine.
13,744 Questions
Where is the crankshaft sensor on a 1991 dodge ram charger 5.2?
It doesn't have a crank sensor. All it has is the "pick up plate" in the distributor, under the rotor inside the cap.
Where is the throttle position sensor on a 1995 dodge ram 2500?
Gas engine, on the throttle body. Diesel engine, on the injection pump.
Where is the IAT sensor located on a 2005 Dodge Ram 1500?
To locate the IAT sensor in a 2005 Dodge RAM 1500, you will first need to shut off the vehicle and apply the parking brake. Find your intake manifold and identify the two intake runners. The second runner will be located a few inches from the front of the intake manifold on the left side. The IAT sensor is located inside of this runner.
Does #1 plug fire? Can you hear the injector clicking (use a long bar held to your ear) like the other injectors. Check fuel pressure, check compression...
My truck ran perfectly but had a #4 misfire code with MIL light on. I decided to park it and fix it since the light began flashing, meaning possible catalytic damage could occur if continue.
I changed a bad vacuum tube under BPT, cleaned a clogged EGR valve to BPT tube, replaced EGR, and most importantly cleaned 1/4" EGR ports in the intake manifold through the 6 Allen key plugs on the manifold. Two 10mm and four 8mm. - Thanks to a Nissan parts guy for the port info.
p.s. use a good quality Allen key socket and a 1/2 breaker bar. daas-in-der-tight!
What causes violent wheel wobble when hitting a bump?
I would suspect either a loose wheel, or worn suspension or steering parts. This is very dangerous. Have the steering & suspension inspected.
AnswerI have a 1997 dodge 3/4 ton, my pickup was shaking real bad when I would hit a bump so I replaced the "steering shock" I do not know if that is what it is called but it is the shock on the front of the vehicle. Replace it and that should fix the problem. AnswerThis is a very common problem on 2nd generation 4x4s, Don't use a stock steering shock get a heavy duty after market one. Another good fix is a Luke's Link, check the link at the side for more information it has great diagrams and instructions to fix the track bar.Get a Bilstein Steering Shock. The problem will most likely go away. I've had 2 RRC's and I did this fix myself on both cars.
Where can i find the fuse box on a 2002 BMW 325i?
inside the glovebox there are two white tabs turn them and the fuse box will drop down inside the glovebox there are two white tabs turn them and the fuse box will drop down
Where is the oil pressure switch located on a 2004 Chrysler Sebring 2.7L?
It is on the backside (firewall side) of the motor. You have to raise the car enough to get under it, you cannot access from top. If your light is on only at idle, there is an updated plug from Chrysler with a vent in it to let out small amounts of oil that leak from the unit. You should change both, but if you only change the sending unit, thoroughly clean the plug that plugs into it to avoid the oil left in the plug creating too little resistance, and turning your oil pressure light on.
Dodge ram starts fine but won't accelerate past 2000rpms?
Check that your Catalytic converter is not blocking the airflow.
Did Ford invent cummins engine?
no, ford did not invent cummins engine, clesie cummins does invented it
Where is cylinder 1 on dodge b150?
I assume you have a 318 CI. Cylinder 1 is located on the drivers side. It is the cylinder closest to the front of the engine. Drivers side: Front of engine 1, 3, 5, 7 back of engine
Passenger side: Front of engine 2, 4, 6, 8 back of engine
Why does your 1996 dodge ram 1500 4x4 keep blowing the dash light fuse?
Fuses That "Blow" Repeatedly
Without being able to "hands on" troubleshoot the circuit served by the repeatedly blowing fuse, none of us can identify the specific defect which is causing your problem.
Therefore, the following generic answer can be applied to any electrical circuit, whether in a vehicle, or in a building, or whether alternating current [AC] or direct current [DC].
Fuses [and Circuit Breakers] are safety devices designed and installed in electrical circuits TO PROTECT the conductors [wires] and other components from short circuit conditions and/or overload conditions which cause an extremely large flow of electrical current [measured in Amperes], which causes overheating of the conductors that results in damage to the insulation and the conductors.
And in a worst case scenario, the probability of a FIRE which could destroy the vehicle, house, or other structure in which the circuit is located.
When a fuse or Circuit Breaker [and replacement fuses, or repeatedly "tripping" Circuit Breakers] "blow," especially if it happens repeatedly, is an indication of an UNSAFE CONDITION in that circuit, usually a short.
The fuse or circuit breaker is doing what it was designed, intended, and installed to do, that is to protect the conductors and components of the circuit which it serves.
The proper "fix" for this issue is for a qualified technician, who knows what he or she is doing, to troubleshoot the involved circuit, find and identify the defect, and make proper repair [s], BEFORE replacing the fuse again [with the properly sized fuse or before resetting a circuit breaker].
Some ignorant few people will suggest installing a larger fuse or breaker to solve the problem, BUT that will only increase the hazard, not correct it.
Do not follow "bad" advice by installing a larger fuse in a misguided attempt to correct the problem. To install an oversized fuse would almost guarantee damage to the wiring and the probability of an electrical system fire.
How many gallons of diesel does a 2011 dodge 3500 hold?
Short bed holds 34 gallons
Long bed holds 35 gallons
Where is heater control valve on dodge ram 1999?
I found mine by locating where all the steam was coming out when the plastic Valve broke....I have a Dodge Ram Van, left side, behind battery is a black box, coming out of that box are two 5/8" dia hoses, top hose about 10-12" away is a control valve with a vacuum actuator attached to it.
I am currently looking for a replacement, cant find one online
How many quarts does a rear end take 1998 dodge ram?
Mos diffs take only a few pints. so less than 2 most likely but it takes special oil and isn't routinely changed
How do you find the rear end gear ratio of a dodge ram 1500 4x4 2001?
See related question below.
See related question below.
How many quartz of transmission fluid will be required at filter change on 4.7 dodge 2 wheele drive?
Between four and six is average.
What is error code P1470 on a 2000 dodge ram 1500 magnum?
Trouble code P1470 means: Leak Detect Pump Pressure Switch Low
How do you tighten the bolt on a 1997 Dodge truck transmission output shaft?
You dont.........you buy a new truck...
Oil pressure switch location on 5.9L dodge ram 1500?
the switch is located on the back of the engine. right behind the intake manifold. right beside the egr pipe.
What causes code p0230 on Dodge Ram 2500?
P0230 fuel transfer pump circuit fault. Usually caused by a failed transfer pump.
