Dodge Trucks

To find a pilot bearing diagram for a 1990 Dodge Dakota, you can refer to the vehicle's service manual, which typically contains detailed diagrams and instructions for components like the pilot bearing. Additionally, online automotive forums or websites specializing in Dodge vehicle repairs may offer diagrams and user-contributed resources. If you can't find a specific diagram, consider checking with a local dealership or auto parts store for assistance.

Yes, when swapping a slant 6 for a 318 in a Dodge D150, you typically need to change the motor mount brackets. The engine mounting points and brackets are different between the two engines, so using the correct brackets for the 318 ensures proper alignment and fit. Additionally, you may need to modify or replace other components, such as the transmission mount and exhaust system, to accommodate the new engine.

To replace the ignition switch on a 1972 Dodge pickup, start by disconnecting the battery to ensure safety. Remove the steering wheel and the steering column cover to access the ignition switch. Unscrew the old ignition switch and disconnect the wiring harness, then attach the new switch and secure it with screws. Finally, reassemble the steering column, reconnect the battery, and test the new ignition switch.

On a 1979 Dodge truck, the engine block casting number is typically located on the driver's side of the engine block, near the engine mount. It can often be found on the flat surface just above the oil pan or near the rear of the block. In some cases, it may also be stamped onto the block itself. Be sure to clean the area for better visibility when searching for the number.

To change the power window motor on a 1997 Dodge 1-ton, first disconnect the battery to ensure safety. Remove the door panel by unscrewing any fasteners and gently prying it off to access the window motor. Disconnect the wiring harness from the old motor, then unbolt it from the door. Install the new motor by reversing the process, securing it in place, reconnecting the harness, and reattaching the door panel.

To change the front right turn signal bulb on a 2001 Dodge Dakota, first, open the hood and locate the headlight assembly. Remove the screws or clips securing the assembly, then carefully pull it out. Disconnect the electrical connector from the bulb socket, twist the bulb socket counterclockwise to remove it, and replace the old bulb with a new one. Reassemble everything by reversing the steps, ensuring the assembly is securely fastened.

I had a 92 dodge i/s ton that sat for a long time.... mice had packed muffler and exhaust system right full of stuff..... had to remove and replace with new before truck would run

If it is a 4x4 the front end by far will be the biggest expense, the automatic transmission gives them plenty of problems, and the injector pump will go out about every 100,000 miles. They are very solid trucks other than that.

it sounds like it might be the cam sensor in the injection pump.

The ac evaporator is located inside the heater housing under the dash on the passenger side.

Clockwise when viewed from pulley end.

You should locate and test the solenoid. Most have three connections. There is a large cable from the battery to the solenoid, from the solenoid to the starter and from the start switch to the solenoid. The power terminals to the battery and the starter are large and have large cables. The starter switch connection is much smaller.

Turning the key to 'start' provides a low current voltage to the solenoid causing the solenoid relay to close and power from the battery cable to connect through to the starter. If that voltage is present then the solenoid or the wiring between the solenoid and battery or solenoid and starter is suspect.

If that voltage is missing then the starter switch or solenoid feed line may have failed.

Probable broken door inside the dash. Have a mechanic check the ac system for trouble codes.

A diagram is also known as a schematic layout. A diagram of a Dodge Ram 1500 rear differential cannot be drawn with letters or words. It is usually created by using a computer program. The diagram may also be different depending on the year the vehicle was made. For instance, the diagram of a 1998 model will be slightly different from the 2004 model. The Dodge Ram website has images of diagrams for the various years of this particular vehicle.

It "tells" the computer the rational location of the distributor for spark timing.

Several things can cause your fuel gauge not to work. The most common cause is a bad ground wire. A malfunctioning float in the fuel tank can also cause the problem.