answersLogoWhite

0

Ford Bronco XLT

The Bronco XLT is one of the three models available for the 1996 Ford Bronco; the other two were XL and Eddie Bauer. The Bronco XLT features anti-lock brake system, a full-size spare tire and a driver airbag.

2,925 Questions

Where is the EEC relay located on a 94 ford bronco?

ECC relay is in a box under the hood on the drivers side. open the lid and look at the inside of the cover and there will be a diagram of where each relay is located.

What is the rear-end gear ratio on a 1994 Ford Bronco xlt?

There are four ways to find a ratio.

1 A dealer can normally tell from the vin number.

2 There are normally tags or labels on the axle that have part number, gear ratio, and fluid requirement

info.

3 You can count how many times you have to turn the driveshaft to get one complete turn of the tires.

4 You can divide the number of teeth on the ring gear and divide by number of teeth on the pinion.

What is the tire size for a 1996 Ford Bronco?

235/75r15 or 265/75r15 or 31x10.50r15 or 32x11.50r15 depending on suspension setup with or without quad shocks.

How do you remove the steering wheel on a 1998 Mazda Protege with air bag?

if you don't know how to do it, hire someone who does. this can be a dangerous procedure, if there is power to the air bag when it is disconnected, it will discharge, it has been know to break unsuspecting necks.

How and what tools are needed to take the hardtop of a 1994 Ford Bronco Eddie Bauer edition off?

You need a special torque socket wrench. Take of the plastic covering to expose the bolts. Then it is simply muscle unless you have a power wrench. Be careful with the clips that are under the metal that the bolts screw into, don't let them fall into the side panels as they are tough to recover. That's about it. Unplug the electrical, lift it up and off with someones help.

A Phillip's head screw driver for interior moulding and a 5/16 socket or wrench. Best to you power tools for bolts as they are long winded and tight. Cordless drill works fine.

Where is the flasher unit on a 1987 Mazda B2200?

The flasher is located under the dash driver side near the left kick panel(plastic cover below the left front speaker).A good idea is to buy a new flasher for reference so when the part is replaced you can identify the part easily!It should be mounted to metal towards fender near the hood latch pull handle area.

Where is the transmition fluid dipstick located in a 1998 passat 1.8 engine?

I have a 1999 Passat 1.8L T and I'm sorry to inform you we have no dipstick. They have sealed transmissions and require to fill them by the top with a 17mm hex to remove plug. Good luck cause I'm having a bit of an issue right now trying to change the seals for the axles and have to replace the fluid also while I'm at it.

Can you smell yourself?

Actually, yes. Everyone can smell themselves! Unless you have a smelling problem.

Your 1989 bronco was running then it died no power to radio windows or heater fan its as if the ignition circuit is not energized no matter what position the key is in?

It is possible that the switch is faulty , but start from the simple things, first check the battery for state of charge, if there is proper voltage, check terminals for corrosion, remove them and clean , then try starting, if not check the main battery connections to motor , and relay, working your way along the system, fuses etc... not being there to see how things are, it's very difficult to give an accurate answer.

Is a 1999 mercury tracer rear or front wheel drive?

A 1999 Mercury Tracer is a front wheel drive vehicle

What is front wheel traction loss called?

There are several words for wheels losing traction; spinning, sliding, drifting, breaking free...

If it happens to the front wheels while cornering it'll cause understeer = the car will continue straight forward despite the driver trying to turn.

How do you replace a heater core on a 1991 dodge dynasty?

Heater core is located under the dash and is held in with i believe 4 bolts which means the bottom half of dash needs to be removed but first you need to pop the hood and disconnect the inner and outter hoses going to and coming from the heater core at the wirewall, be ready cause some Coolant will come from the hoses.