0
Ford Excursion
The Ford Excursion is a full-size SUV produced between 2000 and 2005 by Ford Motor Company. It was based on Super Duty pickup truck platform and served as the largest SUV in its line up.
364 Questions
How many miles you can get out of ford powerstroke 6 litre diesel engine?
My 6.0L is a 2007 model. It's my worktruck and I've got almost 60,000 miles on it with no problems at all. If you think that they are total junk, they're not. My friend has an '06 with 137,000 miles. The only problem he's had is one bad injector. That's it. I worked on a 2003 1/2 model 6.0L Powerstroke that had 331,964 miles. The only repair problems with it were a replaced flywheel and two injectors. He was in the shop for an oil change...
Where are the oxygen sensors on the 2001 Ford Excursion?
It is located on the first portion of the air intake. If you look under the first piece in the chain leading up to the air intake, you will see the wire that connects underneath the sensor. You will have to take it all apart, but really easy to fix.
glow plugs are located in head under the valve covers
the valve covers need to be removed to access these
buy a shop manuel for proper and complte unstructions and diagrams for replacememt
Automatic hubs will not engage 2000 excursion?
The auto hubs are vacuum engaged. Good luck. Worst case, it is a seal in the hubs, and big bucks. Or, it could be a hose behind the brakes. Might need a trimming.
How many quarts of oil in ford excursion 7.3 motor?
According to the 2000 Ford Excursion 7.3 liter diesel supplement :
With engine oil filter change :
( 15.0 U.S. quarts )
How many quartes of oil does a 2001 v10 ford excursion take?
According to the 2001 Ford Excursion owners manual :
With engine oil filter change :
( 6.0 quarts of engine oil ) for the 6.8 liter V10 gasoline engine
Where is the intake air temperature sensor on a 2004 ford expedition?
Mass Airflow Sensor
Operation
The Mass Airflow (MAF) sensor directly measures the mass of air being drawn into the engine. The sensor output is used to calculate injector pulse width. The (MAF) sensor is what is referred to as a "hot-wire sensor". The sensor uses a thin platinum wire filament, wound on a ceramic bobbin and coated with glass, that is heated to 200*C (417*F) above the ambient air temperature and subjected to the intake airflow stream. A "cold-wire" is used inside the (MAF) sensor to determine the ambient air temperature.
Battery voltage from the EEC power relay, and a reference signal and a ground signal from the PCM are supplies to the (MAF) sensor. The sensor returns a signal proportionate to the current flow required to keep the "hot-wire" at the required temperature. The increased airflow across the "hot-wire" acts as a cooling fan, lowering the resistance and requiring more current to maintain the temperature of the wire. The increased current is measured by the voltage in the circuit, as current increases, voltage increases. As the airflow increases the signal return voltage of a normally operating (MAF) sensor will increase.
Testing
1. Using a multimeter, check for voltage by back probing the (MAF) sensor connector.
2. With the key ON, and the engine OFF, verify that there is at least 10.5 volts between the VPWR and GND terminals of the (MAF) sensor connector. If voltage is not within specification, check power and ground circuits and repair as necessary.
3. With the key ON, and the engine ON, verify that there is at least 4.5 volts between the SIG and GND terminals of the (MAF) sensor connector. If voltage is not within specification, check power and ground circuits and repair as necessary.
4. With the key ON, and the engine ON, check voltage between GND and SIG RTN terminals. Voltage should be approximately 0.34-1.96 volts. If voltage is not within specification, the sensor may be faulty.
Removal & Installation (4.6L & 5.4L)
1. Disconnect the negative battery cable.
2. Release the air cleaner clamp and separate the air cleaner halves.
3. Remove the grommet from the air cleaner housing and slide the grommet down the hardness.
4. Remove the (MAF) sensor plate and (MAF) sensor from the air cleaner.
5. Detach the (MAF) sensor from the harness.
6. Remove the retaining nuts and remove the (MAF) sensor.
7. Installation is the reverse of removal.
How do you drop a fuel tank 2003 ford excursion?
how do i drop the fuel tank on a FORD EXCURSION 5.4L
Insulating walls and windows, weatherstripping doors and windows.
How do i replace upper ball joints 2002 ford excursion?
Most of these now require changing the entire arm when replacing the upper ball joints. Any national parts chain will carry them.
How many quarts of oil is required for a 2004 Ford F250 V8 6.0 Diesel?
A 2004 Ford F250 Super Duty Pick Up with 6.0 V8 Diesel engine requires 15.0 quarts of oil.
What is a external mirror on the PC?
To Mirror is the process of backing up a hard drive or another type of drive -- creating a backup copy identical to your main drive. Mirroring a hard drive will protect your important files in the event of a computer virus or hardware failure. Offered by Cloud services and other websites
Why might one want to go on an excursion?
One may want to experience going on an excursion, for example to accomplish a goal in their life. Some also go on excursions to take a break from every-day life and to relax.
Where is the factory reset code for keyless entry on 2000 excursion?
There is no factory reset code for keyless entry on a 2000 Ford Excursion. To find the code, locate the module underneath the dashboard. You may need a borescope to look at the number.
Where do I find the factory preset keyless entry code on a 2000 Ford Excursion?
Remove interior driver's door panel, should be on "brain"
How to fix Ford excursion pulls to right?
If your Ford Excursion pulls to the right, start by checking the tire pressure on all tires to ensure they are properly inflated. Next, inspect the front alignment; misalignment can cause pulling and may require a professional alignment service. Additionally, examine the suspension components and brakes for any wear or damage that could contribute to the issue. Finally, consider rotating the tires to see if the pulling changes, which may indicate uneven tire wear.
Where is the low pressure ac port on a 2000 ford excursion?
Generally it is the one closest to the compressor, and on the larger of the two tubes. Don't worry though, the two fittings are different and the one with the recharge kit will not fit on the incorrect one.
