Pulse-code modulation (PCM) is a method used to digitally represent analog signals.

Check the fuse, bulbs/assy., and wiring another thing to check is where the bulbs connect. sometimes like my 94 one of the connectors in the bulb housing was broken. also there is a brake light sensor on the brake petal that is turned on when you depress the brake. usually near the top of the brake petal

front of the engine above the starter,behind the coil packs (where all you spark plug wires are plugged into) remove all six 5.5 mm bolts from the ignition coils unplug two connectors on the left and one on the right.

starting from the front on the passenger side is #1 then it goes 1,2,3,4 to the back then the front of the drivers side is #5 the it goes 5,6,7,8 to the back front 5 1 6 2 7 3 8 4

Check the Idle Air Control. It might have carbon deposits and need cleaning. Also do the same for the throttle body intake. It might also need cleaning.

36v

Resistance (Ohms) = Potential Difference (Volts) / Current (Amps)

So, 12/0.25 = 48 Ohms.

Diodes are rated to use a certain amount of current. If you go over that amount, it will eventually destroy the device, how long it takes to destroy the device depends on how much more current you are running through it than it is rated at.

Here are a few easy and related equations.

V = Voltage, I = Current (amps)

R = Resistance, (Ohms)

V = I X R

R= V / I

I = V / R

Power = Watts = W, is expressed as V X I. Since V =I X R, W then also = R X I X I

Which is I **2 X R

Same as V**2 / R

So, if your I = 3 and your R = 3, and because I X R = V,

3 X 3 =9 Volts

(Note: capacitance and inductance can also influence the amount of current flow in a system. This resistance is referred to as reactance. Both reactances are a function of the frequency of the Voltage applied.)

Have a wonderful day. Bob

uni junction transistor

No current flows when the the voltage is zero.

It depends upon the connection of the resistors, if the resistors are connected in parallel then the voltage is same where as in case of resistors connected in series the voltage is different across different resistors.

Kirchoff's first rule is a demonstration of law of conservation of charge and his

second rule is a demonstration of law of conservation of energy.

. . convert electrical energy into heat. Electric charge flowing down a potential gradient, as it does in a resistor, is the condition identified by Poynting's theorem for energy to leave the electromagnetic field.

A trimmer resistor usually called a trim pot is a small variable resistor it is used in circuits to do preset it is trimmed with a trimmer screwdriver it is made up with a round fiber disc with a layer of carbon with a wiper that run on the carbon layer to change the resistance it always have 3 connecting pins where the center one is connected to the wiper and the other two to opposite ends of the carbon strip.

You can find the current by using an ammeter. The cheapest way (although more invasive) is to use a probe type ammeter or multimeter. To use, you need to insert the meter in the current path of the resistor (in series with the resistor). These meters are fairly cheap - as low as $8 if you shop around. If it is not feasible to break the circuit and insert the meter, and you have room around a wire going to the resistor, you could use a clamp on ammeter as well. These are typically more expensive.

If you understand resistor codes, you can also use a volt meter/multimeter to measure the voltage drop across the resistor (put the probe in parallel with the resistor). The current should be equivalent to I = V / R.

If you don't know resistor codes, do an online search to match colors with numbers. There should be three stripes. The first two are the resistance and the third is a magnitude. For example, if the first color matches the number 1, and the second matches 8, and the third matches 3, then this is a 18 x 1000 = 1.8k ohm resistor.

where else it would go through.....

the current entering the first resistor must pass through the next preceding resistors in order to reach the positive/+ve potential so as to complete the circuit.

Current flow is the actual flow of electrons so it goes from the ground (negative most point) to th emost positive point. lectrons are a negatve charged unit so they travel towards the positive point.

It is used to dial in a specific resistance within the range of the box. It can be used wherever you need a resistor of an unknown value or a precise value. Most decade boxes provide reistance with .01% of the desired resistance. I've used them to balance a wheatstone bridge that had a tiny mV offset.

V = IR

= 8x10-3 (8 mA) * 10x103 (10k)

= 80v

By Ohm's Law, current is voltage divided by resistance, so if you double both the voltage and the resistance, the current would remain the same.