2003 GMC Envoy and the Blower Selector switch only works on high?
It is the blower resistor. It happened to mine and from what I can tell it is a common problem. Here is a site that helped me it also shows you how to replace it. You can find the part at AM Auto parts. http://www.sparkys-answers.com/2009/01/2002-gmc-envoy-no-low-blower-speeds.html
How do you reset driver 1 seat settings?
Most memory seat problems go on forever. You can visit our forum and read through some threads about it but IIRC most members have just pulled the fuse.
www.trailvoy.com
Where is fuse box in 04 gmc envoy?
Theres two one is under the hood on drivers side and the 2nd one is under back seat on the drivers side
Where is the Coolant Temperature Sensor on a 2004 GMC Envoy 6 cylinder?
On the 05 4.2 it is tucked behind the alternator and difficult to see unless you are standing on the driver's side.
One of the front wheel hub and bearing assemblies is bad and it chewed up the abs speed sensor. Don't drive any further than your nearest garage for repair.
What would be the likely cause of a randon misfire code P300 on a 96 GMC Sierra 5.7 liter?
Try changing the fuel filter. It'll be fuel or spark related, so start with the cheapest thing.
The problem was the distributor cap, I put a standard motor cap and a AC-Delco cap on it. Water would get up and cause the misfires. Summit has Accel products at a good price (less than AC-Delco and Standard). Its been 6+ months and no misfires.
How do you clear the service engine soon warning in a 2003 gmc envoy XL?
You can disconnect the battery for 15-20 minutes and it will reset. Your best bet is to find out what code was set. You can diagnose the problem from the code.
All the answers are at www.trailvoy.com
The true enthusiasts website for Trailblazers and Envoys!
What octane gas do you need for a 2002 1.8T Beetle?
Try 87 Octane, if it does not "ping" excessively you should be OK, If it does "ping" try 89 Octane
Show how to replace front right wheel bearing 2004 GMC Envoy?
Unfortunately,we have no way to show you or do drawings.
Where is the oil sending switch on 2002 Envoy?
On a 2002 GMC Envoy, the oil pressure sending switch is typically located near the oil filter on the engine block. It is usually found on the driver's side, towards the rear of the engine. You may need to remove some components for better access, depending on the engine configuration. Always consult the vehicle's service manual for specific details and diagrams.
What is the lug pattern of a six lug 2002 GMC envoy?
Trailblazers and Envoys are 6lugs x 5" circle. (6X5). The half ton trucks and SUVs are 6x5.5".
Adds air to the exhaust to burn any unburned fuel in the exhaust system before it is released to the atmosshere
What is Air pump whine on 2005 trailblazer?
Probably not the air pump. Could be the power steering pump or the tensioner pulley or maybe the idler pulley.
How do you know what fuse is for what on a 2004 gmc envoy XUV?
www.trailvoy.com All your answers for your truck are here!
How do you do a tune up on a gmc?
There is nothing to tune up on a GMC Envoy except to change the plugs at 100,000 miles.
Follow the manual for regular oil and drive line lubrication fluid changes.
www.trailvoy.com Envoy enthusiasts forum!
The newest GMC Envoy is a 2009 Envoy. The base price is between $30,000 and $38,000. With being that the company has not made more Envoy's since 2009, the pricing is high. with a rating of 60 out of 100.
How do you reset the check engine in your car 2003 GMC Envoy?
Have vehicle scanned to determine the problem and have codes cleared
How do you get to the shift lock release lever on the 1998 Bravado?
you hit the tolit first you go to the engine pull the black thing and pull it out look threw it and try to get around the engine by cutting the black thing get the engine out be tacking a hammer and hitting it
Don't know off hand but you could always pull the lower radiator hose and drain it that way.
Where is the pedal position sensor on a 2005 envoy?
The pedal position sensor on a 2005 GMC Envoy is typically located on the accelerator pedal assembly, which is situated on the driver's side, near the floor. It is mounted directly on or near the throttle pedal and is connected to the vehicle's engine control module (ECM) to monitor the position of the accelerator pedal. To access it, you may need to remove some trim or covers from the footwell area.
How do you replace an ignition key cylinder on a GMC?
You have to remove the steering wheel and the turn signal switch. but move to the side. It should be empty. There should be a screw where the cylinder is. Just unscrew that and the cylinder should slide out. And make sure not to push the shaft where the steering wheel attaches too. Its a pain to get if you push it in.
----------------------
There are other concerns....you probably have an airbag in the steering wheel. You MUST disconnect the battery for at least 15 minutes to power down the airbag or it can go off. I usually wait 30 minutes.
You will need a special tool to compress the steering wheel lock plate to remove the snap ring.
You will need a steering wheel puller. Also a Torx drive bit to remove the key cylinder pin/bolt combo.
Just take your time and pay close attention where all the parts go. I wish i could be there to help.. I've done a TON of GM steering columns.
One last thing...NEVER have someone in the drivers seat when you re-connect the battery. If the air bag is going to blow that is the time that it will go.
Best of luck...
Yeah I didnt think of that. Was thinking of an older model truck. Thanks other dude for your input.