GMC Envoy

check this site 1st its not a straight forward job.. http://forums.trailvoy.com/search.php?searchid=1710816

The 2007 GMC Envoy rear wiper blade size is a special 12" rear wiper blade that is very simple to replace once you find a replacement. Unfortunately, most stores do not stock this special rear wiper blade so please see sources and related links below for more information and installation videos. Once you get the wiper blade, there will also be step-by-step instructions on the packaging.

My 2005 holds 21.7 gals. Found out because gas gauge didn't work.

under the vehicle, there is a spash guard protecting the engine. in this spash guard there is an approx 6 or 8" door panel. using a flat head screwdriver turn the screw a quarter turn to the left. the panel will be loose, spin the panel so it out of your way. the drain plug is right there and a little put up in the hole is the filter.

Basically you just cut the pipe right before the resonator, and it should come right off. After that you can either weld a new one on (which I wouldn't), put on a extra bit of pipe, or nothing. Mine was ruined, and after I took it off everything was great. It sounds nice when you rev it, but isn't loud or obnoxious otherwise.

if jolt means engine stumbles or misses when power is needed or shakes at idle usually its a bad ignition coil each cylinder has a coil on top of each cylinder.check for codes and look for a misfire code also replace all spark plugs as worn plugs tend to burn out coils because they have to work harder to work harder to jump worn spark plug gaps

5w-30

BOLT PATTERN IS 6x5" OR 6x127mm.

Code B0265

Price it out at www.rockauto.com

Try disconnecting the battery for 20 minutes. This should put the computers into a reset mode.

www.trailvoy.com The Trailblazer/Envoy enthusiasts forum with all the answers!

Its under the hood towards the back. Check for a red colored dipstick handle.

1. Apply a liberal amount of penetrating oil (ie. WD-40) to the contact point between the oygen sensor and the exhaust manifold. Let it sit overnight. 2. Run the vehicle for about 10 minutes to warm up the exhaust manifold. 3. Shut off the engine. 4. Disconnect the positive battery post. This will prevent any electronic damage when the wiring harness is disconnected and reconnected. 5. Disconnect the plastic clip on the sensor's wiring harness. 6. Using an oxygen sensor removal socket ($30 at the auto store) unscrew the sensor. $30 seems like a lot for a socket that you may only use once, but because of the heat shield, it is about the only way to access the sensor. Initially it may take considerable force to break the threads free. Once the sensor has started to turn, you may want to apply more penetrating oil. 7. Thread in the new sensor. Make sure that the threads on the new sensor have anti-seize on them. 8. Connect the wiring harness. 9. Re-connect the battery.

remove intake duct to throttle body and clean iside of throttle bore with carb. cleaner. throttle plate sticks and disrupts air flow. this air flow should increase when ac turned on but cant if plate stuck...djones1...chevrolet dealership

nope, 7

Just follow the instructions on the owner's manual it's easy or call the number they give you there

You don't. Take it to a dealer. It is dangerous to work on the air bag system. This is not a DIY project. The light staying on indicates there is a problem with the system.

I'm sure you can get some help with this from on of our members at

www.trailvoy.com An enthusiasts forum that really helps!

> what are the steps of programming a keyless remote for a 01-05 gmc envoy 1. Close all vehicle doors. 2. Insert the key into the ignition. 3. Hold down the power UNLOCK button on the driver's door panel-continue to hold down until instructed to release in step 9. 4. Perform steps 5 through 8 in fairly rapid succession. 5. Turn the ignition switch to the ON position (as far as you can go without starting the engine). 6. Turn the ignition switch to the OFF position. 7. Turn the ignition switch to the ON position. 8. Turn the ignition switch to the OFF position. 9. Release the power unlock button on the door panel. The vehicle will lock and unlock the doors automatically. 10. Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the door locks and unlocks. This step may take up to 30 seconds. 11. Repeat step 10 NOW for each additional transmitter (including any existing transmitters). 12. Turn the ignition switch to the ON position in order to exit the transmitter programming mode.

The 2003 GMC Envoy inline 6 engine does not have a timing belt but a timing chain. No need to replace anything unless the chain breaks.

It is located behind the alternator just above the thermostat. You will need to take the alternator off to be able to reach and change the sensor.

This will 100% depend on the brand of remote start, it will come with instructions.

On the other hand I like my system best, I take my car to the local stereo shop and have one put in. I would rather work on my race car than spend a frustrating day putting one of these in.

If the TPS or Throttle Positioning Sensor goes bad on a 2004 GMC Envoy SUV, the car will have a very rough idle. The engine might stall frequently and the cruise control will not function properly. The car will also use much more fuel than is necessary.

any vehicle will roll on incline if brake is not used sort of like a tennis ball will roll down a hill if nuthin there to stop it if you use the transmission in idle to hold you on slight incline, all you are doing is wearing out components .brakes are made to hold vehicle still, transmission is to move you not hold you

Remove speaker grill covers on dash to expose tweeters then remove door panels and you will se the rest of speakers