0
GMC Sierra
The GMC Sierra is the latest series of full-size pickup trucks from the American car builder General Motors. The GMC Sierra is known for its luxurious interior, unique grille and four-wheel steering system.
2,525 Questions
Where can I get a wiring diagram for a 93 GMC Sierra 4l60e transmission?
Hayes and chilton make manuals for all kinds of vehicles, that would be where i would check. They're usually available at your local auto parts store and if they dont happen to have the one you need they can probably order it. I would check with all auto parts stores in your area to see if there is one you can check if that schematic is in there before buying though.
you may also be able to register at autozone.com and find the wiring diagram in their "free vehicle repair guides"
How do you reset 4x4 service light on 2005 gmc sierra 1500?
Someone answer this please. I have an 03 sierra and don't know if I have a problem or if it's just time for maintenance.
Removing stock radio in 1998 GMC sierra?
you must remove the dash panel that goes over the stereo, heater and around the gauges then all you have to do is pull it out just by pressing two tabs on each side of the stereo
What is the horsepower of a 91 GMC Z71 4x4 with a 5.7 liter 350?
The horsepower of this vehicle is 250. When you are looking for a new vehicle keep in mind what you are going to be doing with and whether or not you will be towing anything in order to determine how much horsepower you need in it.
Who makes a supercharger for a 4.3L Chevy?
Wynjammer is about the only company that makes a supercharger for the chevy 4.3L. It's a belt driven turbo style supercharger like a Vortech instead of a roots type supercharger like an Eaton or Whipple.
See this document: http://www.jpcustoms.com/store/documents/signalmirrors.pdf This is actually a procedure to install some mirrors, but the process of removing the panel is shown. Jack
Where is the knock sensor located on a 2006 gmc sierra 4.8?
There are 2 of them, And they are underneith the intake manifold.
You will have to remove the intake manifold to get to them.
What causes brake light to blink on dash in 1993 GMC Sierra 1500?
Worn brake pads can cause the brake light to blink on the dash in a 1993 GMC Sierra 1500. This can also be caused by a faulty light.
How do you install torsion bar keys on 2005 Silverado?
jack up front end, drop both bolts out of the torsion keys, knock both bars out then put new keys in
Where is the Knock sensor in a 2000 GMC Sierra?
they are located under intake manifold The #1 sensor is located in the front of the engine and the #2 sensor is located in the back of the engine. Remember to replace the intake gaskets once you replace the sensor/s. The total time it took me to pull the intake and locate the bad sensor was about 6 hours. Hope this helps
How do you drain the radiator on a 1994 GMC Sierra?
Open the petcock at the bottom of the radiator and drain into a pan. If there is not a petcock, then remove one end of the 94 GMC Sierras bottom radiator hose to drain the system. The coolant is toxic to animals so dispose of properly.
How do you replace a fuel line?
bleed the fuelline of the fuel left in the line.
remove the fuel line by unscrewing the couplings.
replace the line and screw the couplings back.
bleed the fuelline of as much air as possible.
try to start your engine until it starts
What is speaker size for the cab of a 1999 silverado ext cab?
front main are 5.1/4 with a baffle rear are 4 by 6 with a baffle front baffle found on eBay . you can make the front work with a 6 1/2 but you must drill it in glue it,exc..
How can you test a ignition module for a 88 gmc pickup?
Remove it and bring it to a NAPA store. They will test it free.
What is a kocking sound in the engine and go away in a minute or two?
Preignition. If timing correct, you need more octane in your fuel.
Where is gmc sierra keyless entry module?
What year.For my 1997 it is located on the metal bracket right above the gas pedal and it a small black looking box.
How do you replace passenger door mirror on 2006 gmc sierra?
1500 2500 3500 or denali? Try this site out it gives step by step guide on what to do, parts, etc. Plus has pictures to help as well. I just did a basic gmc sierra.
http://www.carpartswholesale.com/diy_center.php?part=Mirror&sku=GM59L&brand=Kool+Vue
How do you program the remote control key fob for cars?
NOTE: There is nearly ALWAYS separate programming for keys & remotes, even if they are one unit. One Exception is newer Chrysler all in one units which are programmed as one unit. These can not be self programmed.
All SMART keyless for remotes - Nissan - Lexus - Toyota - Hyundai - All can NOT be self programmed.
Audi - Nearly All require special equipment for programming for keys & remotes.
BMW - Hit and miss on programming. The keys can NOT be self programmed.
Buicks - Erratic. La Crosse - NO Onboard self Programming Available
Cadillac - Most from 1998 to 2000 require special equipment for programming -
Except Escalade which can be self done. ALL CTS - NO self Programming
Dodge & Chrysler Products - Many require one existing & working remote to program additional units.
If you have no working unit, then special equipment is required to get these done.
There is no "Other" programming available to help you if you have NO existing remote.
Chrysler Crossfire - can NOT be self done - key or remote.
1997 1998 1999 Dakota & Durango - No programming Available.
Dodge Charger - NO self programabilty on board.
All Chrysler combo units, meaning key and remote in one, can NOT be self programmed.
Ford - Nearly ALL KEY programming requires 2 working keys. If you have just one key, You will NOT be able to program additional keys on your own. Nearly ALL Ford Remotes CAN be self programmed. Fords are generally the easiest of all to program.
GM - HHR, Colorado, Cobalt, SSR, Uplander, Canyon, and 2001 & newer Malibu & Malibu Max. These require special equipment for programming. Circle Plus Keys CAN be self programmed.
Some GM Products have a split year whereby part a year may be programmable,
and part may not. There can also be two or more different remotes for some models in the same year.
Hummer H3 2006 and newer
Honda Ridgeline - NO Self Programming
Hyundai Tiburon - THE 2003 TIBURON AND MAYBE MORE ARE INCREDIBLY SIMPLE!!!!!!!!
1. Get in the car and close the door.
2. Turn the key to the ACC posistion
3. Push the unlock button on the remote until the blikers flash once.
4. Get out of the car and test the remote. It should be working fine.
Hyundai Elantra - 2006 and Newer are not self programmable.
Tucson - NO On Board Programming
Jaguar - Most newer vehicles require special equipment for programming. Model S definitely can NOT be self programmed.
Jeep - Grand Cherokees from 1997 to Present require special equipment for programming Cherokees from 1997 to 2001 require special equipment for programming
Land Rover - Nearly ALL require special equipment for programming
Lincoln - LS Model - Some years may require special equipment for programming
We definitely DO have 2003 to 2006 AVAILABLE for self programming.
Mercedes Benz - Some require special equipment for programming for keys & remotes. Many MB dealers are uncooperative & will give you a gigantic run around, and tales abound. We know for a fact that many can be done.
DO YOUR HOMEWORK !
Oldsmobile : 2000 & Up Aurora NO Self programming
Pontiac - G5, G6, 2001 Grand Am & later, Grand Prix 2004 & Later, 2006 & Later Montana Pontiac Solstice - NO On Board Programming
Saab - All Years require special equipment for programming for keys & remotes
Toyota - Prius Silver Logo Smart unit is NOT self programmable.
Volvo - All except early 850, require special equipment for programming
Another case of a lot of hogwash flying around. Some need a code, others DO NOT.
However, some dealers will tell you differently as they do not want to let you off cheap
Where is the sending unit for the fuel on a 2001 GMC Sierra 1500?
It is in the fuel tank ---- part of the fuel pump ---
How do you change starter on a 1996 gmc sierra?
the starter should be on the right side of the engine block there aretwo or three bolts going into the block then the starter should come down a little but on the front of the starter there is a nut holding on wires to the starter i think they are 10mm. once the bolts are out of the block and no wires are on the front of the starter it should come out. its a 10 minute job if that
