answersLogoWhite

0

🌼

Interior Design

Planning the furniture placement and layout of the inside of a building is what Interior Design is all about. It is the branch of architecture that deals with the selection and organization of furnishings for an architectural interior.

5,109 Questions

How do you decorate a teen girls bedroom?

Add beaded curtains or a funky lamp. Add a dark contrasting colour somewhere in the room to reduce the zing of the orange and give it a little finesse. Dark brown, black or deep blue are possibilities

5 yards of 60'' wide fabric equals how many yards of 57'' wide fabric?

Area of first piece = 5 yards * 60 inches = 300 inch-yards

Suppose length of equivalent area of 57" fabric is x yards

then x*57 = 300 or x = 300/57 = 5.26 yards (approx).

What is the proper towel bar arrangement?

The proper towel bar arrangement should have one bar near the sink, and one bar near the tub or shower. The towel bars should be arranged so that towels are not getting wet while running the water in the sink or bathing. A lower height bar should be used for small children.

How do you sneak out of your house with a security alarm and two story?

easy,

all you will need is:

a knife

some tape (dosent matter what type, as long as it sticks well)

there are 2 parts to any window alarm, a sensor which isn't connected to the window (the part that moves) and a little bar thing that is stuck to the window, the little bar is magnetic and when it moves away from the sensor (i.e. opening your window) it triggers the alarm so the idea is to be able to open the window without moving the bar

all you do is very carefully put the tape on the sensor so that it is also stuck to the magnetic bar, then use the knife to pry the bar off the window (or unscrew it, but its usually attached with double sided tape) without getting it unstuck from the tape that connects it to the sensor, when done the magnetic bar should hang from the tape attached to the sensor, then open the window and presto, freedom!!!, i sudjest then carefully without moving the bar away from the sensor, moving it closer is fine, reinforce it so that your sure it wont come off, i did this to the window in my room and have done it to sevral friends windows aswell, it works like a charm just becareful while doing it, i have heard you can also put a magnet there but personally i prefere this way because its gaurenteed to work, just be careful to keep the bar the same distance if not closer to the sensor than it was in the first place and the alarm wont sound, the beauty of this trick is you can leave it like this so you don't hafto do it again

as far as the 2 story part goes i sudjest finding a tree to climb onto or if there isn't one buying one of those rope fire escape latters, they work perfectly (probably because that's what their designed for lol) if you cant find one or cant buy one just build one, if u cant do that use a rope or somthing, but i highly sudject buying a rope fire escape latter or somthing

and that's pretty much it,

have fun sneaking out

Anyone who tells someone else how to bypass an alarm is an idiot. That person has no idea what the age or purpose for someone asking such a question. Obviously the alarm was placed there for a reason. Do you think you are going to pull the wool over your parents eyes? You also have to be quite unstable to even want to sneak out in the middle of the night. Sooner or later you will get caught and any trust and stability your family had in you will be gone. Can you REALLY live with that for some cheap thrill?

What country does oak wood come from?

The tend to favor the cooler climates. Pretty much every country on the planet that fits that description and has trees, has oak trees.

What are the Instructions for basting stitch?

Please see related link. * http://www.expertvillage.com/video/122946_how-sew-basting-stitches.htmAnswer 2:

A basting stitch is the simplest stitch you can make. You push the threaded needle through the layers of fabric, and bring it up about 1/2 inch away. It works best when you keep the stitches as straight and even as you can. Since it is a temporary stitch, it doesn't have to be perfect. The reason for the basting stitch is to hold the pieces together until you finish sewing or working with the project.

How do you get emulsion off walls?

Getting emulsion off walls can be difficult. The easiest, and best way would be to sand it off. You could also try using a blow dryer to heat it up and then scrape it off.

What are mud huts made from?

Because depending on where they live they need to use available materials. Also they move often to find fertile soil so the houses can't be permanent and need to be easy to make.

some africans..... actually most dont live in mud huts and africa is a continent so just dont say africa.

How can you keep your room clean when you hate cleaning?

If you get something out, make sure you put it back before you leave your room. That way, you never have to clean a lot, and your room stays clean.

Why is MDF good?

Comes in a variety of thicknesses, from 30mm down to 3mm. Can be cut, drilled and routered cleanly ,and can be sanded very smooth. Easy to seal and paint, with very good adhesion. Sonically inert, so is the best material for speaker enclosures. The thicker MDF is strong and rigid, and the thinner sheets can be bent into even , smooth curves, making it an excellent pattern an mould making material. Cheaper than solid timber. Glues together strongly with PVA glue. Polyester fillers (body filler) sticks well . Its main disadvantage is that it is not waterproof.

Cost per foot to install drop ceiling?

It depends on what the people that estimate your particular job in your localized area feel they can get from you and how much the particular ceiling material costs, and how difficult an installation it might be. Get estimates from local contractors which have done good work for your neighbors and friends.

Average size of laundry room?

A laundry room is a designated room in the home where clothes and linen are washed, dried and pressed. There is no standard or average size of a laundry room so you can design yours in such a way that meets your needs.

What is the standard spacing for coat hooks?

The standard coat hanger is 17 inches long. However, coat hanger dimensions vary in size just as much as they vary in design and styles. Materials used to make coat hangers include: wood, plastic, and metal.

How do you tone down yellow paint?

To tone down yellow paint, you can paint over it with a different color. You can also add white to the paint.

How do you build a table for 12 people?

You might need the 108" and it probably would not fit in your dining room. I do not know if the 72" would even fit there, or if it would be large enough. You might be better with a rectangle or oblong table.

How much fabric is needed to make a full size bed duvet?

Hi, I just came back from the fabric district yesterday. I got some material to make a duvet for my daughter's king size bed. You need 11 yards according to an employee at Michael Levine's in Los Angeles.

How do you take glue off a painted wall?

You can try scraping it off with a putty knife. If you happen to gouge the drywall in the process, use drywall mud over the spot, smooth it over with a putty knife. After it dries, try sanding it. If it is still not flat, scrape on a bit more drywall, allow to dry and sand again.

How do I cut cove molding?

Answer

Use a miter box or a miter saw.

First, some assumptions:

A) The moulding used has a 45 degree "spring" or slope.

B) the corner you are cutting, inside or outside is 90 degrees.

There are 2 ways to do this, depending on whether you have a simple mitre saw, or one with compound mitre/bevel capability.


1) Using a mitre saw ( no compound bevel capability):

Place the "top" (ceiling) edge of the moulding closest to you, on the saw bed.

Place the "bottom" edge on the fence of the saw.

Position the molding at a 45 degree slope between the bed and the fence.

The molding is now bridging the bed of the saw to the fence at 45 degrees.

Set the saw mitre to 45 degrees and cut the molding

Cut.

For the mating piece, reverse the blade miter and bevel, and cut with the material pointing from from the opposite side of the blade.

2) Using a compound mitre saw (compound miter & bevel capability):

Place the back of the moulding flat on the bed of the saw.

The "bottom" edge goes against the fence

The "top" (ceiling) edge is closest to you.


Set the saw miter to 35.3 degrees

Set the blade tilt (bevel) to 30 degrees.

Cut.

For the mating piece, reverse the blade miter and bevel, and cut with the material pointing from from the opposite side of the blade.


If the angle, or "spring" of the moulding is not 45 degrees ( 38 degree moulding is quite common, fro example), or: If the corner is not 90 degrees, then you will need a table to work with.

These may be purchased here:

http:/www.compoundmiter.com/chart.html#cr-mld-table

I also found free ones here:

http://www.extremehowto.com/xh/article.asp?article_id=60354


And, Remember to protect your fingers!


Inside corners should be coped not mitered in good quality work. Butt one piece to the corner. Cut the other at 45*, which will give you a line along the face of the moulding. Using a coping saw (hence the name), cut along this line at a right angle to the length of the piece. Butt this second piece to the first to complete the joint. If the corner is obtuse then you will have to over-cut with the coping saw to achieve a tight fit. This method obviates an inside mitered corner opening when nailed up.

How do you make a woven wall covering?

To make curtains, you will have to first measure your windows and the length you want. Cut the fabric with two inches seam allowance on each side and bottom, and eight inches on the top. Then sew your seams, and sew the top edge as a tube through which to run your curtain rod.

How much does it cost to remove vinyl siding on a house?

Unfortunately there is no magic formula as you need to consider thickness of siding, location (close to ground, several stories up, etc.), access routes, local landfill costs, etc. You should contact an asbestos removal contractor is your area for a proposal.

What is the average size of a two bedroom house?

It depends on the zoning and the area and year the house was built but it could be from anywhere between 1,500 and 3,000 Sq Feet.

Can you get a list of the retired home interior figurines?

I also have some for sale, please email tommyguz@gmail.com

I have some for sale. I have about 22 of the like "evening of romance" , 'lady Caroline and Victoria the are in mint condition in a glass case , email me and I can send you pics j.green4178@comcast.net

I am looking for a home interior homco masterpiece Jesus with Joseph The Carpenter figurine... I do not have the item number and am not for sure of the name of the item... it was a hostess gift. If anyone has one for sale please contact me at jcpetw@aol.com