Mitsubishi Mirage

This is located near the engine. It lets you know when the engine is getting too hot and the coolant is running low.

there is two ways to remove to hubs. the first is brut strength, pry at it with a flat hub bar or screwdriver. the other way is, look at the hub u will see a wire running around the hub, there is a spot on the hub that is flared where the hub meets the rim nearest the tire. find this spot put a wide flat screwdriver or hub bar in till it is past the hard wire running throught the rim and pry till it gives. then move around the rim and pry till the hub pops off

Possibly, remove the back seat and see for yourself.

there is a few rubber exhaust hangers, if they break the exhaust can rattle, also you have heat sheilds that point the heat away from the passenger compartment, with the car off, tap the exhaust pipe with your foot at the back of the car and listen for a corresponding rattle.

how to replace crankshaft sensor on Corsa 1-2 2002 .Which parts require removing to replace unit

After removing the wiper arms, carefully pry up the plastic grill. There are, I think, 5 plastic pins along the bottom of the grill and 2 at the two top corners. They'll fly away if you're not careful. With the grill off, there are 3 nuts around each wiper post and one behind the wiper motor that you can get at after removing 4 screws around the motor and pulling it away from the firewall.

Before you remove any nuts though, you may be able to repair your existing transmission by simply popping the socket at the end of one or more of the arms back on to the ball connected to the wiper post.

hi bubby the order is 1-3-4-2

10 amp fuses position 4 and 5 in the fuse box on the right side of the engine compartment near the battery.

The gas tank on the 2002 Mitsubishi Mirage holds 12.4 gal..

on the rigth side behind the radio, is a small metal box with a bolt

On a 1999 Mitsubishi Mirage, the engine oil capacity is: 1.5L engine: 3.2 quarts 1.8L engine: 3.7 quarts

Replacing the turn signal switch involves replacing the entire turn signal assembly. Remove the screws from the steering column cover to remove the top of the steering column. You can take off the bottom (I was able to work around it). There are only a few screws holding the turn signal assembly. Remove the screws and unfasten the electrical connectors.

The 2001 Mitsubishi Mirage is 14 ft. 0.1 in. (168.1 in.) long.

Behind the bumper underneath the left headlight, except for the 4-door and the 1.8L models, where it is underneath the right headlight.

You need either a code scanner or a analog volt meter. With the scanner, you just need to read the codes. WIth the volt meter, you'll need a chiltons or hanes manual to see where to hook it up.

does Mitsubishi mirage have a map sensor 1.5 1996

It depends on what you call high rpms but, anything above the normal driving range for long periods of time will reduce the life span of that engine.

Do you mean 'idle' - like turned off? Or idling with motor running and gear in neutral? Either way, white smoke (not just white or clear steam) usually means burning or burnt oil. Check engine seals and manifold gaskets - or maybe worn piston rings.

A 1997 Mitsubishi Mirage DE Coupe needs spark plugs that have been set with a gap of .043 inches. This is equal to 1.1 mm.

Most dashes are held on by Christmas tree type brackets or screws. there for you should first look for screws under the ash tray, glove box, and side panels were the door opens. if its old enough the screws will around were the steedometer is. if you are unable to locate any screws you should be able to pop off the front dash with fingers of a screw driver. good luck

no

does a Mitsubishi mirage have a map sensor 1.5l 1996 The 1994 Mirage 1.5 California, has a MAP sensor aka fuel injection vacume sensor. NAPA part number CRB 219245. When this part is faulty there will be several problems. The most common, the car will fire and stall. Or the car will run for only a short while and stall. This part effects both engine ignition and fuel management.

IF ITS NOT LOW ON OIL IT MOST LIKELY IS AN OIL SENDING UNIT .YOU MAY WANT TO HAVE SOMEONE LOOK AT IT ...THE SENDING UNIT COULD START PUKING OIL AT AND TIME IF ITS BAD

The clutch slave cylinder in your 1998 Mitsubishi does not use fluid. The clutch slave cylinder is sealed with grease inside of it.

Looking at the engine , you will have to locate the transmission dip stick first. This is a small white ball(mine is white ) located on the left side of the compartment, below and back from the battery.You should first start the engine, transmission fluid should be checked with the engine running, wipe off the dip stick and reinsert the stick , then pull it out and see where the stick shows how much fluid you have . If it shows that it is low,, add some , and check again.This is where you will add the tranny fluid. You will need to use a long funnel to do this. . Try not to over fill. Hope this helps you.