0
Toyota Sequoia
The Sequoia is a full-size sport utility vehicle (SUV) manufactured by Toyota Motor Corporation from 2000 to the present. This model is sold exclusively in the Middle East, the US, Puerto Rico, Mexico, Chile and Canada.
1,008 Questions
Where is the cabin air filter in a 2009 Toyota Matrix?
Look under the dash on the passenger side. Probably right above the blower. Refer to owners manual. Walmart carries Fram cabin air filters.
How do you access the tail lights to change out the bulbs?
open the reear doors and look on the side of the light assembly there are 2 screws , remove them and gently roll the light assembly to the outside of the quarter panel , then twist the light bulb holder out to access the bulb.replace bulb and reverse prcedure to reinstall. Use a magnetic tipped screw driver. There is a channel between the access hole and the mounting point, very easy to drop the screw from a normal screw driver.
Does a 2002 Huyndai Elantra have a timing belt or timing chain?
All 2002 Elantra's are listed as having a timing belt fitted For the1.6, 1.8, & 2.0 ltr engines Best wishes
How do you remove the center console on a 2002 durango?
There are 7 bolts to be removed. 4 under a linner in the rear compartment, 2 under the cup holder and 1 under the insert at the front of the console. Theres also a an electrical plug to undue under the console once the bolts are removed. 15 minute job. Ted
How do you replace the front O2 sensors on a 2001 Toyota Sequoia?
Unscrew them and put in new ones. They can be very difficult to remove, as they tend to become frozen in place and are difficult to access. I tried to get Bank 2 Sensor 1 out and it was hopelessly frozen in place and very difficult to access. I will try penetrating lubricant from Kano labs, as suggested on a website. WD 40 and Parts Blaster were worthless.
Why does your 97 Lexus ES300 idle rough after changing the timing belt?
You do not have the correct timing set for that car.
Honda recommends it -- But I would not have it done for at least double ot even triple the mileage they recommend.
How do you replace a Toyota sequoia front interior door handle?
This answer includes info posted at:
http://www.tundrasolutions.com/forums/1gen-sequoia/121854-repair-broken-door-handle-sequoia-2003-a/#post1102387
Also see:
How_do_you_open_the_driver_side_door_panel_for_a_2003_Toyota_Sequoia
....................................................................................................................................
First - get the replacement part on hand.
Note that on several of the parts-house websites, they show an exploded line-drawing diagram of the door with the various parts. It is difficult to figure out which of these parts was supposed to be the door handle. This is because its not just a handle but rather a rectangular frame with the lock and handle lever installed within it - so the simple line drawing makes it hard to recognize.
The part can also be obtained from a local Toyota dealership. For example, I recently (July 2008) bought a replacement Driver's Side front door handle from my local dealer - Price $27.30 + tax. The Toyota Part number is: 69206-0C030-E0 (tan color - may be a slightly different number for the grey interior). It is referred to as the "Handle Sub-Assy, front door". A separate part - called the bezel - is also available, but it is not necessary to replace this when replacing the door handle assembly (i.e., the exitsing bezel can be reused).
The following instructions were originally posted by: bboop4fun (1-13-2008) under the webforum title "Repair Broken Door Handle Sequoia 2003"
"...Open the door and remove the three side pins along the door jam, take off the three small cosmetic covers and unscrew them (they are the front corner just under the window speaker, the other one is inside the door handle cup and then just below the door pull/arm rest). When you get these off you can take a flat head screw driver and put it in between the door lock and the frame of the door handle, give it a little pop up and then do the same to the bottom...now you will be albe to slide this door handle frame back (to the right) and it comes right off. Now start at the bottom of the door panel and find the two slots and put a flat head screwdriver in and pop the panel off by moving around the edge of the door panel as you go around. There will be about 5 to 6 red push clips holding this portion of the door on. Once the door is off you will have to disconnect the door light wire harness from the bottom of the inside panel and then the auto window/door lock wire harness from the center of the door panel. You are ready to remove the handle and replace it with the new one...very easy to do...slide the whole door handle to the right and it comes right off, turn the piece over and then remove both of the wires from the slots, put the new wires in the same place on the new handle and put it back up to the door and slide it back to the left. Now make sure that all of the red push clips are removed from the door itself. It is much easier to have them attached to the door panel. Once that is done you just need to attach the top of the door panel at the window first, this is a little tricky since you have to clear the speaker at the front of the window, one this is done it is just a matter of giving a little push around the edge of the door panel to snap the red push clips in place. Put back all of the screws and cosmetic caps. When you put the frame back around the door handle you have to first make sure that you get the front part cliped in first. The easiest way was to hold the handle open slighly and put the frame on then in the middle of the frame cup push in and forward (left) to make sure this catches on the clip. Then the right side will just clip on to the top and bottom of the new lock and handle. If you have a gap at the top of the handle door frame, just slide the flat head back between the new lock and frame and give it a push up and then do the same for the bottom. Once the frame is free you can try to slide the front clip on first and then push the back in. I had a harder time getting the passengers side on without a gap, but did not have the same problem with the drivers side. I think it was because we may have pushed the door panel in a bit when trying to figure out how to get the whole panel off. Once you know that there are only three screws and a bunch of push clips are holding the whole panel in place so it isn't that hard to do."
THANKS SO MUCH FOR THE INFORMATION! I just completed the repair of my broken drivers side door handle on my wifes 02 Sequoia. I believe the only minor correction to your plans would be that when you were referring to sliding directionally to the 'to the right' you were working on your passenger side doors. Whereas if it's the driver's side door handles, the correct direction would be 'to the left' to get the door handle clips out of the door frame. Otherwise, it took me all of 15 minutes. Also got couple of fuses changed out to get her side mirrors/clock/cig lighter (iPod) working again. Oh yeah, i was only able to locate 2 push pins on the driver's door not 3.
Repair 2002 Sequoia rear door latch?
You need to removed the plastic cover on the inside and manually un-lock the latch. There is no easy way. The dealer want $270 to $290 if they do it.
How many gallons does the gas tank in the 2013 Toyota Sequoia hold?
The gas tank on the 2013 Toyota Sequoia holds 26.4 gal..
How do you replace your rear speakers in a 1990 Lincoln Town Car?
The speakers are removed and accessed top side. There is a speaker grill extraction l made. But the grill can carefully be pried loose with one or two table type butter knives. The speakers themselves removed with the fror Phillips screws and unplugged from the speaker harness. On grill replacement it is often necessary to use a plasctic glue as age can make the grill too brittle to replace by the crimp method. The JBL speakers are 6X9's. If you're into doing a bit of soldering, you can use any high quality 3 way speaker and reduce the prices to about $35 each instead of the nearly $70 each or the originals. BTW, the door speakers are 6X6 or often referred to as 6.6" and also 3 way speakers. They are accessed by the conventional door clips. You want to be caareful here too as plastic clips get brittle.
How do you locate the spark plugs to change them in the Sequoia?
the plugs are under the ignition coils that line the top of both cam covers(on the left and right sides of the intake) remove the plugs that are on each coil. remove the 10mm bolts that hold them in. pull the coils out and remove the plugs with a 5/8 spark plug socket on an 8" extension
How do you change the antenna on a 1997 Toyota 4runner?
I have a '94 4Runner that needed a new mast so I went to http://www.antennamastsrus.com/ and ordered a new one for about $30. The instructions were good and the fix was easy. Although, shortly after install my motor stopped working altogether. I am positive that the new mast didn't cause the problem, I think it needs a new fuse or relay. Hope this helps.
Some people like to and some people only do it if there is a stain out of the seep hole on the pump.
Change tail light bulb in 2002 Nissan altima?
Across the trunk opening is a gray plastic piece about 24" long the trunk latch hole is in the middle. Pull straight up on that plastic part. Next remove the two trunk net hooks on the side the bulb is out.. by prying out on the top round piece and remove the trunk net hooks pull back on the trunk gray liner see two 8mm nuts under white plastic wire clips. pull off the wire clips and ramove the 8mm nuts and pull toward the rear the entire tail light assembly. There are bulb holders (3) of them tail light, turnsignal stop lamp, and back up light bulbs. Replace the bulb correctly and push the lamp assembly back onto the pawn shaped pins then put back the two 8mm nuts and reassemble the trunk. Source: Yahoo Answers
Where is the jack kept on a 1993 E-150?
The jack is kept in a large leather-like bag in the rear compartment. Basically, if you don't see it while looking around in the rear of the van, you don't have one.
How do you reset the security system on a 1997 Toyota?
---- ====== ====== i briging quite back yea ---- ====== ====== i briging quite back yea
What is the curb weight of the 2006 Toyota Sequoia?
The curb weight of the 2006 Toyota Sequoia is 5090 lbs..
