answersLogoWhite

0

Chevy Blazer

The Chevy Blazer may refer to any of the sport utility vehicles manufactured by the Detroit-based automaker General Motors Company. Some of the popular Blazer models produced by the company are the TrailBlazer, the S-10 Blazer and the K5 Blazer.

5,824 Questions

Where is the spare tire on a 96 Chevy Blazer?

the spare tire should be on the under carriage under the trunk of the Blazer

Where is the starter on a 99' Chevy blazer?

It is located behind the wheel well on pasenger side. Next to the transmission case.

How do you prime your 4.3 Chevy oil pump?

Buy a primer tool, connect it to a large drill motor and spin clockwise for several minutes....

Can you remove the driveshaft to your front axle for better mileage without harming anything?

I assume you are talking about a four wheel drive vehicle. If you have a transfer case that lets you select between 2 and 4 wheel drive you can remove the front shaft with no problem. Many later model vehicles do not let you chose 2 or 4 drive-- they have a limited slip unit in the transfer case. If you take out the front shaft in one of these, the rear shaft will not work.

Where is the solenoid located on a 1999 Subaru Outback?

It is the small canister attached to the starter itself sometimes with a heat shield on it. The cables attach to the solenoid.

Will a 1994 astro transmission fit a 1991 s10 blazer?

It'll fit, but it won't work. The 94 transmission is electronic, and interfaces with the ECM. It won't be compatible with the 91 in that regard.

What speed can you drive in your 94 s10 blazer when it is in 4 high before you start hurting it?

First, you don't drive in 4 high on paved roads when the roads are dry. If you are driving off road or in snow it won't matter how fast you go, it won't damage anything but you may lose control and crash and that would hurt it.

How do you fix a vacuum leak on a 2000 Chevy Blazer?

Need to know the location of the vacuum leak in order to answer this.

What would be the cause in your 89 Comanche inline 6 that will stall on deceleration?

I found it to be the throttle sensor on mine. Cost me about $40. And put it on myself. It's looks like a small wire harness under the end of the airintake hose coming from the airfilter box.

Base 2 sensor 1 where is it on the 2003 blazer?

Assuming you mean bank 2 sensor 1, it would be the first O2 sensor located in the header pipe after the passenger side exhaust manifold.

What does the windshield wiper module look like on a 1998 Chevy S-10 blazer?

It is attached to the wiper motor. The wiper motor is attached to the firewall under the hood. The module can be replaced without removing the wiper motor. Unplug the wire harness leading to the wiper motor. Remove the three small torx head screws and remover the flat black plastic cover. The module inside will slide out with a gentle pull. New modules are available from your local auto parts store.

How do you change alternator on 1989 s10 blazer?

take off the belt unplug the wire connector form the back of alternator take the nut off the back of the alternator that holds the wire that is connected to the positive battery terminal and take the two bolts on the bottom of alternator that holds it to the engine

How do you differentiate the single acting actuator and double acting actuator?

The working pressure acts from one side in single acting actuators while in double acting actuators strokes generating by each side.

What is a bearing knock?

A bearing knock, or a rod knock develops when the bearings between the rod and crankshaft wear, leaving a gap, allowing the crankshaft to slap the connecting rod. The knock develops slow for a few miles but once the rod starts to knock then the gap increases because the metal in the rod and the crankshaft get destroyed and deteriorated. As the gap increases the knock gets worse, and as the gap increases the knock and the damage will rapidly get worse. Within a short while the connecting rod will break open and get stuck between the crank and the engine block, possibly cracking the block and destroying the crankshaft. The engine is now inoperable :<

To prevent the rod knock, let your engine warm for a minute or so before driving to ensure the engine oil has been pumped throughout the engine, and get regular oil changes, because a thin film of oil is all that separates these engine parts, and dirty oil will be squeezed between the metal parts, increasing the rate of erosion. .

Where are the sparks plugs located on a Chevy Camaro 3.8L V6 1999 Camaro?

The spark plugs in the 3.8L V6 are located directly below the valve covers on each side of the engine. They are very difficult to get to in the Camaro, because the engine sits so far back in the engine bay. Follow the wires to find the plugs. (3 per side) Look for the six flexible wires going from the tom of the engine to the sides. There should be three a side going from the common point (the distributor cap) to three spark plugs on each side. i have a 99 camaro and i just changed plugs. To change them you have to get under the car and they are about middle way on the block. they are a pain to get too and you will need a swivel socket to get to most of them. There is only 1 you can get too from the top of the car. make sure you let you car cool down. 2 plugs are right by the exhaust manifold.

Where is the fuel regulator switch on 1998 Chevy blazer?

you have to take off all kinds of stuff around where your breather is you have to take the throttle body off and there is a black plate thing under that you have to take it off it has about six or so bolts on it ...it is hard but dont give up then when you get that off the injectors are in like this little free standin oval shape thing on the back off that thing is the fuel pressure switch GOOD LUCK .we just changed ours..