Chevy Blazer

on your 2000 Blazer the control module is located under the kick panel on the passenger side. Simply remove the plastic panel, unbolt the module with a 10 MM socket and disconnect the wiring hareness. While your there, check the wiring hareness for corrosion as this is a big problem. apply Dielectric grease to the hareness and install new control module.

Well, removing a blazer fuel tank can seem like a daunting task, but with a little patience and care, you can do it. First, make sure to disconnect the battery to prevent any accidents. Then, carefully detach the fuel lines and the straps holding the tank in place. Remember to work slowly and methodically, and don't hesitate to ask for help if you need it.

Attach the wiring harness to the end of the ignition lock cylinder. Slide the ignition lock cylinder into the slot. Tighten the retaining ring at the top of the cylinder.

Minnesota won the NIT tournament in the year 2014.

A code scanner is the most valuable too for giving relatively complete information regarding an EFI engine. About the only things it won't check are fuel pressure, function of the fuel pump, status of the fuel filter and whether the injectors are fouled.

If it blows air, clockwise. If it is pulling air, it is counter clockwise

Yes Actually they do.. A scientist named Mike McAdams did a test on how long it took for the light to change without pressing the button, which took 2 minutes to change, but then he pressed the button and it only took 1 minute, 28 seconds.!!! And there is a code that allows you to change the light Immediatley by the button itself. Here is the Code: 3 Fast Clicks, 2 clicks, holding on the each of the two for atleast 5 seconds, 1 fast, 2 held ones again, and then 3 fast clicks, So it should be: click click click, cliiiiccckkkk, cliiiiicccckkk(holding down for 5 seconds), click, cliiiicccckkk cliiiiicccckkkk, then click click click!! Try it out

If the displays for the heater and gas went blank simultaneously, it is likely a fuse issue. Check the fuse box for any blown fuses related to the displays. Replace any blown fuses with ones of the same amperage to restore functionality. If the problem persists, it may be a wiring issue that requires professional inspection.

To change a velocity joint in a 1996 Chevy Corsica, you will need to first lift the vehicle and remove the wheel. Then, disconnect the drive shaft from the transmission and remove the old velocity joint. Install the new velocity joint, reconnect the drive shaft, and put the wheel back on before lowering the vehicle.

try the cool line fitting from the radiator to the transmission i just had that problem on a 1994 mercury

Sometimes you can leak out of the tailhousing of your transmission if the housing seal is slightly damaged

To put together the '95 Dakota automatic shift linkage, first ensure all components are clean and free of debris. Then, following the service manual, align and connect the shift rod to the transmission lever, ensure proper adjustment, and tighten all bolts securely. Finally, test the shifter to ensure it shifts smoothly through all gears before driving the vehicle.

take the pin out of the rear diffrential and the axle should come out

The center section of the upper area of the that encloses the upper light assembly needs to be removed. It is plastic and is clipped in so be careful. After you remove this section the light assembly may or may not be attached to this piece. You need to unattach it and remove the bulb which is a 21 18W D bulb, standard rear brake light bulb in most American cars. Replace bulb and replace assembly then reclip the plastic section to the door. Be careful the plastic clips can break.

First, make sure it isn't a window switch. many people have bought expensive replacement motors, when the problem was only the switch in one of the doors. If one switch is bad, the other one will not work & the window will not move. If it is the motor, then is is strongly advised to buy the motor with the regulator attached to it. The doors on these trucks are a PAIN to work with. Take off the plastic door panel, unbolt the inner steel door panel, be careful & release the linkages, while tilting the steel inner panel to unhook the regulator from the window. this is NOT a fun job.

you have to remove the starter to replace the relay and the relay cost almost as much as the whole starter so you are better off just replacing the whole starter.

I believe that it is very touchy and you have to do it very gently so that the off lines up with the one on the knob exactly and if your's is as smooth as mine it is very hard to find that line with out going over or under.

I am not a mechanic by any means, but a nice mechanic at Tires Plus showed me where the Constant Relay Module was yesterday. Of course, that was after they sold me a freon boost and let me drive away without telling me that my air conditioning still did not work. I had to call back the next day to receive an estimate of $340.00 to have a new module installed. From what the mechanic showed me and told me - The module is located on the driver's side, front section of the engine compartment below the air filter. You must unclip and remove the air filter/intake cowling. Look straight down and you should see the little black box or module. You pull out the old one and install the new one, making sure that the pins match. From my reading, you probably need a screwdriver to remove the the screws holding it down. If you are handy with circuits, switches, and soldering, you may be able to repair the module itself, using a relay switch ($4.75) from Radio Shack or just a soldering iron ($ 0.00). Do an Internet search on relay switch, soldering, CCRM, Radio Shack, etc and you should find a detailed explanation of the process. Good luck, CWB

The relay signal is found in the glove compartment, pops right out.

Added comment:

Don't be misled. The glove compartment in a 1996 Blazer that has AC only contains relays and does not drop down with a simple release mechanism. In this vehicle, the lower dash panels do actually need to be removed in order to access the flasher. You'll need Torx bits and hex sockets to accomplish.

Disconnect Negative (-) battery cable from battery

Crawl under the passenger side of the truck just behind the right front wheel (if you are as thick as me in the middle the truck will need to be raised up, safely please.)

There are two (2) 15mm head bolts holding the starter to the engine block from below.

There are two or more wires attached to the starter, usually 8mm and 15 mm wrenches or sockets needed.

Undo wires

Unbolt and do not drop starter on your head (I have done this, ouch)

The wires may need to be undone with starter hanging loose

Reverse procedure for install.

Ok to start with you have to remove the grill and the chrome around the lights. Then between the hood and the front plastic/fibreglass there is a crack with five hex screws the middle screw is smaller than the other four, take em out, there is two nuts one on the left and one on the right they are hidden under the chrome light cover hence the need to remove thelight surrounds. once all this has been done remove the plastic/fibreglass and unplug the turn and marker lights. Now the important part as the Cherokee has two latches one on the left and one on the right so from the front of the vehicle on the right take a long screwdriver and looking in under the hood push the little piece you can see to the right, now the left latch should pop up. Dont bother with the right latch as it also moves to the right but you can push on anything to open it. Now with the hood left side up you can reach in and grab the thin bar and pull it to the left and voila the hood will open. Removing the cable is eay just unscrew the door plate not all the way just loosen two screw closest to the dash and remove the two screws holding the plastic cover on the side wall and you can get it out. Next remove the three that's right three screws holding the release cable to the side wall. Next remove the two screws holding the fuse box to the front wall. Next remove the cable from under the hood just pop it out and open the two clips holding it to the hood. You can now pull it out through the fire wall and installthe new one the same way it came out you'll need a helper to push on the rubber stop as you pull the cable through from the engine compartment. Screw everything back in place and there you have it opened the hood and replaced the cable. www.a-pluspawnbrokers.co.nr

It may be true for this model year, but for a 2000 Jeep Cherokee (mine), it isn't this complicated. Remove both headlight bezels and both headlights. Behind the headlight bowl/socket/cup (thingy that the headlight sits in), there are two bolts. One goes straight up and down from the upper part behind the headlight socket and takes a 12mm socket. This holds the top part of the striker. Just offset from center toward the outside of the vehicle is another bolt that takes a 13 mm socket and is the only one you can really see. This one requires use of a universal to get to the socket. This is the only other bolt holding the strikers to the vehicle. Once you have the four bolts out, use something soft to gently pry the hood up and it will be released as normal from the center latch. I used the above method and succeeded in scratching the leading edge of my hood and the trailing edge of the grill.

put the key in the keyhole and turn it while holding the detent(the little metal cylinder that sticks out of the flat portion of the outside of the unit) when you feel the detent drop that's where the key needs to be. now slide the whole thing just as it is into the socket on the steering column, making sure its completely seated. voila!

place a coat of resin onto metal. then sheet of fiberglass, then resin, then fiberglass, and so on...until you achieve your desired thickness....PS: You will want to roll out the air bubbles every 2 to 3 layers for best results

Walt Disney's choice of musical entertainment has evidently not been recorded in the annuls of history, however a quick web search does show one of his favorite Disney songs was Feed the Birds from Mary Poppins.