0
Chevy Camaro
This category covers general questions about the Chevrolet Camaro, a pony car manufactured by General Motors and sold through its Chevrolet division. The Camaro was designed to compete with the Ford Mustang. Production of the model began in 1966.
4,208 Questions
What would you replace if the fan is not working in your 2004 Chevy Impala SS?
The problem may be the BLOWER MOTOR RESISTOR. This part is pretty hard to get to, it located on passenger side, on the floor up against the fire wall. It is approx. 2 1/2" x 1 1/2" and looks something like a circuit board.
How much horsepower does a supercharged 2011 SS Camaro have?
2011 Camaro SS is not supercharged from the factory. If you put a supercharger on it, the horsepower rating will depend on how much boost you use. A stock 2011 manual transmission SS Camaro comes with the LS3 engine rated at 426hp, and a 2011 stock auto trans SS Camaro comes with the L99 engine, which is rated at 400hp.
How remove tensioner pulley on a 2002 camaro 3.8?
One bolt holds the tensioner to the engine, take it off to get the tensioner off and then you can get to the bolt that holds the pulley to the tensioner.
The letters rs represent the car as the "Rally Sport" model.
Why does my 91 Chevy Camaro start when sprayed with starter fluid but not on its own?
Bad fuel pump or fuel pump relay. Maybe a bad fuel pressure regulator. You need to determine if the fuel pump is working.
How do pull a engine out of a 1996 Chevy Camaro 3.8?
you can pull it from the top but its a lot harder you have to take off the plenuman ac comp. an all that.. the easy way (if you have the means to do so) is from the bottom. that's the way the factory installs it. ive done it three times now an it takes like 2hours to drop the engine if you know what your doing an have the tools from start to finish. an i normally take a break while working because im lazy ha. but its like 6 bolts total on both sides of the subframe 3 on each side an 2 on each side for the sway bar. 4 on top on each side for the struts but i take thoughs out last. undo your fuel lines which will take a specail tool undo all the wiering that you see that leeds off to the body powerstearing lines need to come undone or just take off the powerstearing fluid container. UNDO your break lines, don't forget because when you drop it it WILL ruin them.. undo a bolt on the stearing shaft an when the engine is ready it will just pull off. undo the trannie cross member an the tourtion bar that runs to the rear . undo the exahost an then drop it but ou have to be able to pic up the car body over the engine, an that can be hard, actuly the hardest ppart i think.. wel i hope this mess of words have helped somewhat. an doubble check every thing b4you drop it..
Which is faster a v6 2002 Camaro or a v6 2002 mustang?
A 2002 V6 Mustang has a 193 horsepower. The 2002 V6 Camaro is 200. Check the torque on cars also, Not only horsepower.
How much is a new 5th generation Chevy Camaro?
The lowest price brand new is about $25,000 but there is more information on the new Camaros at this website: http://www.chevrolet.com/camaro-family/
How do you change the front heater core on a 94 Chevy Silverado?
Take off glovebox, undo computer by taking plugs out, pull out, take old freon out and put new in.
Where is the temperature sensor on a 1996 Camaro 3.8 that tells the fan to kick on?
The coolant fan switch is located on the intake manifold near the thermostat. The fan should come on about 232 to 235 degrees and turn of at or near 195 degrees. Check on rear of radiator near top--should be plug with two wires
How do you change a thermostat on a 1995 Chevy Camaro 6-cylinder automatic?
follow the top radiatior hose to the engine block housing. the thermostat is located under the housing. 1. drain the fluid into something. remember most anti-freeze is toxic. Animals like it. it tastes sweet to them. 2. Remove the hose, usually a hose clamp holds it in place. loose the clamp to remove the hose.take the housing off. wiggle, or tap lightly with a small hammer at the base of the housing. the thermostat is underneath. It should just lift out. Make sure completely clean both mateing surfaces. If there is rust in the system, this a great time to flush the system to get the crud out. make sure the thermostat is the correct one for your vehicle. The new one should come with the needed gasket. attach the gasket per the manufacture instructions. reassemble. make sure refill the system with the proper type and amount of coolant. It is usually a 50/50mix, or you can get it and mix it yourself. Not difficult. plan on about 1-2hours to do the project. hope it helps. duboff
Where can you find a 1981 camaro belt diagram?
Repair manual. Check alldatadiy.com for easy access to your car's repair reference.
The fuel filter is located under the car on the frame just in front of the gas tank. It will require a special tool to replace it.
Do you need to use a o2 sensor in a z28 camaro?
Yes depending on the year of your Z28. The o2 sensors give the computer the information it needs in order to control fuel. With out it, high emission's and poor fuel economy will be the result.
-
How do you change a fuel pump on a 1996 Camaro 3.8 liter motor?
You have to remove the gasoline tanks, and you need to go to a car parts store, and get a repair manual for your car. They cost about $16.00 Or, go to a Public Library. Assembly instructions will come with the new pump.
Recieved a cost estimate of 1,000 to replace fuel pump in 96 Camaro. In addtion to the fuel tank, dealer also said drive shaft and axel will have to be removed. 4/055/05
I too received an estimate for almost $1000, many years back and decided to do it myself. You basically have two options. First option is, you put the Camaro on a car lift, take the driver's side tire off. Take the Muffler off, heat shielding...etc... Remove the braces around the gas tank and lower the tank. Oh wait, did I forget to mention that it hits the axle and suspension on the way down and gets wedged in? Thanks Chevy, that makes sense... So all you have to do is pop off the rear drivers side shock, twist the neck of the tank sideways, bend the metal neck it a little and pull hard on that fuel tank to get it to come down. Disconnect 3 hose lines and 2 electrical connections and then there are 7 mini-bolts holding the actual pump in the tank. Swap pumps and reverse previous directions. This takes anywhere from 3.5 to 6.5 hours depending on your competency level.
Option 2 is to open the hatch/trunk up, lift up the carpet and pad....cut a giant hole or square (your choice) through the metal unibody about where you think the fuel pump (center of the tank) is, disconnect the hoses/electrical lines, unbolt the pump out of the tank and viola, you're half done is about 14 minutes. Swap pumps, swig a beer, and repair the massive hole you just cut through your unibody trunk metal. I recommend putting it on a hinge. Total time should be 1.5 hours and now you have an access door when your stupid fuel pump goes out again...
Difficult and expensive to do. Involves finding/purchasing a traction control (ASR)computer and installing it. ASR(Acceleration Slip Regulation) interfaces with and coordinates PCM(Powertrain Control Module) and ABS(Anti-lock Braking System). Most of the required harnesses should be present in all vehicles. Try buying a shop manual for that car and then finding a vehicle in a junk yard from which to pull the necessary components.
How long is the 2010 Chevrolet Camaro?
The 2010 Chevrolet Camaro is 15 ft. 10.4 in. (190.4 in.) long.
