0
Chevy Cobalt
The successor to the Chevrolet Cavalier that was designed as a competitor to compacts like the Honda Civic
1,195 Questions
Causes of froth in power steering reservoir?
The fluid is probably contaminated with water. Change out the fluid with fresh. Check often, if froth returns suspect a leak in the system that enables water entry from either the road or If the unit has a cooler in the radiator, the cooling system.
How do you bleed a Chevy cobalt clutch?
I don't know what model year you own, but on my 09, it says that the clutch system is does not have its own fluid, but is tied into the brake system and its fluid. That makes sense to me, seeing that clutch fluid is merely brake fluid.
How do you change the battery in a key fob for a 2006 Chevy Cobalt?
Get the correct battery CR 2032 remove fob from key ring Carefully, and slowly pry the two halves of the case apart. Start with a very thin ( utility blade) device to allow a heavier ( metal nail file) into the crack. The case will split in half. Remove battery and replace..carefull to keep the positive side up. Make sure it is clean and dry inside. Replace cover by starting in one corner and move your pincer grips slowly around perimeter..Then test it .
What is the proper operating temperature for coolant in a 2009 Chevy Cobalt?
between 176 and 216...at which point the fan should come on and cool it down.
Where is the fuse box on a 2008 Chevrolet Cobalt?
There are two fuse panels, one behind the kick panel underneath the dash, just on the right side of the center console. Just pull it off, you'll see the little fuse symbol beneath the vent on the panel. The other is under the hood, in the engine compartment.
Does a 2007 Chevy Cobalt have a timing belt or chain?
does a 2007 Chevy cobalt with a 2.2 L engine have a timing belt or a timing chain ??
it has 2 timing chains one runs off the water pump crank and internal engine balancers and the other runs the cams and the crank
How do you reset oil life display on 1999 Oldsmobile Aurora?
On my aurora, I just hold in the reset button.............
What is average coolant temp for Chevy Cobalt?
Depending on the weather I would say 175-185. 195-205 is Hot. 210 is boiling. 220 and it is evaporating. 230-240 will be damaging your engine. 250-260 will be breaking your engine.
I've had alot of heater core and radiator problems with my car so I've been there.
I have a 2010 Chevy Cobalt LT 2.2L L4 engine so what are NU6 emissions?
NU6 is the GM code for the California Emissions PZEV (Partial Zero Emissions Vehicle) standard. This means that your car meets California's SULEV (Super Ultra Low Emissions Vehicle) exhaust standards and has no loss at all from fuel evaporation. In addition, to meet these standards ALL emissions related components on your Cobalt must have a 15 year, 150000 mile warranty. For more information, a web search of PZEV will lead you to more exact details on these standards.
How to remove the door panel in 2006 Chevy Cobalt?
first you have to remove the part where the mirror is adjusted on the inside, it snaps off with 3 clips. You can stick a screwdriver under there wrapped in a little duct tape to keep it from scratching the door. After you do that, you have to remove the clips from the door handle in the middle and the door opening handle near the top, and remove the screws/bolts there. Make sure there are no bolts under that mirror cover that you just removed, then just start going around the door, its got the same clips as the mirror cover does, it will require some effort, and 1 or 2 can bend...chalk it up to chevy.....
How do you install airbag in 2007 Chevy Cobalt diverside?
On The Rear Of The Airbag Housing There Are Two Small Holes, One On Either Side. Take A Small Flat Blade Screwdriver And Poke Around In The Hole Till You Release The Spring On Either Side That Holds The Bag In Place. The Bag Will Pop Out A Bit. Once Both Sides Are Released The Bag Is Free. Unplug The Two Airbag Connectors By Pulling Up On The Center Clip Lock, And Then Squeeze The Two Tabs On The Sides Of The Connectors Together And Pull Out. The Airbag Connectors May Be Melted To The Air Bag. You Will Then Have To Replace The Clock Spring
Need RADIO wire diagram for Chevy Cobalt 2006?
2006 Chevrolet Cobalt Car Radio Stereo Wiring Diagram
Car Radio Battery Constant 12v+ Wire: Red/White
Car Radio Accessory Switched 12v+ Wire: The radio harness does not provide a switched power source. Run a wire to the fusebox for switched power. The accessory turn-on and amplifier turn-on are controlled by the class 2 serial network.
Car Radio Ground Wire: Black/White
Car Radio Illumination Wire: Gray
Car Stereo Dimmer Wire: N/A
Car Stereo Antenna Trigger: N/A
Car Stereo Amp Trigger Wire: N/A
Car Stereo Amplifier Location: N/A
Car Audio Front Speakers Size: N/A
Car Audio Front Speakers Location: N/A
Left Front Speaker Positive Wire (+): Tan
Left Front Speaker Negative Wire (-): Gray
Right Front Speaker Positive Wire (+): Light Green
Right Front Speaker Negative Wire (-): Dark Green
Car Audio Rear Speakers Size: N/A
Car Audio Rear Speakers Location: N/A
Left Rear Speaker Positive Wire (+): Brown
Left Rear Speaker Negative Wire (-): Yellow
Right Rear Speaker Positive Wire (+): Dark Blue
Right Rear Speaker Negative Wire (-): Light Blue
How do you reset the the oil light on the 2008 Chevy Cobalt?
Turn on the key but don't start the car. Push the gas pedal to the floor and release 3 times. It will now reset.
How do yo change a side marker light on a 2007 Chevy Cobalt?
unscrew the light from the car, it should pop out. Twist the light bulb out and then pop the light off from the base.
Reverse to reassemble.
Why does your 2005 Chevy Cobalt sometimes make a whining sound when you step on the gas?
It could be your serpentine belt slipping, you should have the car checked out before it gets more serious.
Supercharged Chevy cobalt oil?
I would use what the owners manual recommends.
It may be written on the oil cap .
How do you change the shifter knob in a 2006 Chevy Cobalt 2dr LS coupe?
If it's automatic look on the front of the shifrt knob towards the radio, and on the bottom of the knob you will see a push in horseshoe pin that has to come out to take the shifter knob off.
How do you reset the security system on a 2006 Chevy Cobalt?
Expert: john replied 1787 days and 3 hours ago.
HelloCustomer
I am sending the programming instructions for your theft deterent.If this proceedure does not work you have a problem that must be repaired first.I would start by scanning the vehicles computer system for failure codes.
Programming Theft Deterrent System Components
Programming Replacement PasslockTM Sensor, BCM, or PCMImportant:•The body control module (BCM) must be programmed with the proper regular production option (RPO) configurations before performing learn procedures. Refer to Body Control Module (BCM) Programming/RPO Configuration in Computer/Integrating Systems.•If replacing the BCM with a GM Service Parts Operations (SPO) replacement part, the module will learn PasslockTM sensor data code immediately. The existing powertrain control module (PCM) however, must learn the new fuel continue password XXXXX the BCM is replaced.•If replacing a PCM with a GM SPO replacement part, after programming, these modules will learn the incoming fuel continue password XXXXX upon receipt of a password XXXXX Once a password XXXXX is received, and a password XXXXX XXXXX a learn procedure must be performed to change this password XXXXX A PCM which has been previously installed in another vehicle will have learned the other vehicles fuel continue password XXXXX will require a learn procedure after programming to learn the current vehicle password.
ConditionsUse this procedure after replacing:
•The PasslockTM sensor•The BCM•The PCM
Learn ProceduresThere are 2 available methods to perform the programming procedure:
•A 10-minute procedure which requires a Tech 2 and a techline terminal.•A 30-minute procedure which does not require the use of any tools.
10-Minute Learn Procedure- Connect the Tech 2 to the vehicle.
- Select Request Info. under Service Programming System and follow the instructions.
- Disconnect the Tech 2 from the vehicle and connect it to a techline terminal.
- On the techline terminal, select Theft Module Re-Learn under Service Programming.
- Disconnect the Tech 2 from the techline terminal and connect it to the vehicle.
- Turn ON the ignition, with the engine OFF.
- Select VTD Re-Learn under Service Programming.
- Attempt to start the engine, then release the key to ON, vehicle will not start.
- Observe the SECURITY telltale. After approximately 10 minutes, the telltale will turn OFF. The vehicle is now ready to relearn the PasslockTM Sensor Data Code and/or password XXXXX the next ignition switch transition from OFF to CRANK.
- Turn OFF the ignition, and wait 5 seconds.
- Start the engine, the vehicle has now learned the password.
- With the Tech 2 scan tool, clear any DTCs.
- Turn ON the ignition, with the engine OFF.
- Attempt to start the engine, then release the key to ON, vehicle will not start.
- Observe the SECURITY telltale. After approximately 10 minutes, the telltale will turn OFF.
- Turn OFF the ignition, and wait 5 seconds.
- Repeat steps 1 through 4 two more times for a total of 3 cycles/30 minutes. The vehicle is now ready to relearn the PasslockTM Sensor Data Code and/or passwords on the next ignition switch transition from OFF to CRANK.
Important: The vehicle learns the PasslockTM Sensor Data Code and/or password XXXXX the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle.
- Start the engine. The vehicle has now learned the PasslockTM Sensor Data Code and/or password.
- With a scan tool, clear any DTCs if needed. History DTCs will self clear after 100 ignition cycles.
Expert TypeMaster A.S.EAutomotive technicianCategory: ChevyPos. Feedback: 99.2 %Accepts: 4071Answered: 3/15/2008
Experience: A.S.E MasterTechnician A1-A8 w/L1,38 years experience GeneralMotors Master Technician
Ask this Expert a Question >
How do you remove head restraints on a 2007 chvrolet cobalt?
If you face both seats looking out the back window, on the right side of the head rest is the button you push in and the rest slides up and down. On the left side is the same button only under the beauty ring. You can very carefully pull the ring up and under it is the same push in type button. Pull the rest all the way up, push the left side button and it comes off with ease.
