0
Chevy Corvette
Launched in 1953, Chevy Corvette is a sports car manufactured by General Motor’s Chevrolet division. Harley Earl designed its first model, a convertible. It is Commonwealth of Kentucky’s official sports car.
4,587 Questions
Do you have a vacuum diagram for 1969 wiper door silenode?
I do have a diagram if you post your e mail or fax no. I will share it.
How do you reset tire sensor C5 corvette?
1)Turn ignition on.
2)Press "Reset" button in order to clear any IPC display warning messages.
3)Press and release the "Options" button on the DIC to scroll through the display options until the IPC display is blank.
4)Press and hold the DIC "Reset" button for 3 seconds.
5)Press the "Options" button again until TIRE TRAINING message appears.
6)Press "Reset" button until the IPC "Learn L Front Tire" message appears in order to begin the programming.
7)Install the J41760 Tire Pressure Monitor (TPM) System Programming Tool (large magnet will do) over the left front valve stem.
8)The horn will sound, indicating the left front TPM sensor is programmed (if this takes more than 15 seconds, pull magnet back and try again, it will give you three tries. Then you must start over).
9)When the horn sounds, proceed to program the next TPM sensor in the following order as directed by the IPC messages: -Learn R Front Tire -Learn R Rear Tire -Learn L Rear Tire Programming can be canceled by turning ignition off, waiting 2 minutes with no sensors being learned, finishing all 4 wheels or through the DIC. If the programming is canceled with less than 4 sensors learned, it will only accept the codes programmed up to that point.
How to remove rear bumper on 1989 corvette does gas tank need to be removed first?
YOU CAN NOT REMOVE THE GAS TANK UNLESS YOU REMOVE THE BUMPER. THERE ARE NUTS LOCATED ALL THE WAY AROUND THE SEAM WHERE THE BUMPER MOUNTS UP TO THE BODY. 10MM NUTS. YOU NEED TO FOLLOW THE NUTS AND START REMOVING. YOU NEED TO REMOVE THE LISCENSE PLATE TO ACCESSS THE NUTS NEAR THAT AREA. UNHOOK ELECTRICAL TO BULBS ON THE WAY.
How do you remove the shift knob on a 1997 Nissan Maxima?
It's easy. To remove the shift knob, grasp it firmly and twist it counter-clockwise, like you would the top on a bottle. That's it. Nothing fancy.
Does the security system on a 1987 corvette stop the engine from turning over?
The VATS security system prevents the starter from turning and thus the engine from turning over. Also, the entire ignition system is not activated unless the proper VATS key is used.
How do you remove the Corvette C6 front license plate?
This is right down the same line as "where the horn is"! At any rate, just go on over to Smokinvette.com and talk to some of the members there and they can answer any question that you can possibly come up with! Good luck!
Will a 400 sbc work with a TPI set up?
I assume you are wanting to replace A 350 with A 400? It will run but not correctly, It probably won't even have the power of the 350, You need to either put on A carboretor or get an aftermarket injection system, Also if it is newer than 92' the auto tranny will not work because it is controlled by A computer that takes info. from the motor.
How can you get your headlights to close on 1986 Nissan 300zx?
i had the same problem....it was the headlight relay....bought some off eBay for a dollar apiece.....20 bucks at the store...also could be your pushbutton on the left side of the dash is unplugged.
AnswerThere should be "emergency knobs" behind the headlights to raise and lower them. Or you could connect a 12v dc source to them and they will flip up and down.Will fuel pump run if fuel pump relay is bad?
No because when you have the key switched to the on position even before you start the car the relay switch triggers the pump to turn on and deliver fuel up to the engine to be combusted. If the switch is not working then it cannot trigger to turn the fuel pump on and deliver fuel to the proper location
What is the curb weight of the 2004 Chevrolet Corvette?
The curb weight of the 2004 Chevrolet Corvette is 3214 lbs..
What is the cam type of the 2009 Chevrolet Corvette?
The 2009 Chevrolet Corvette has overhead valves (OHV).
How do you disengage the door lock on a 1979 Corvette?
Cure: I sprayed lots of ether (or degreaser or carburetor cleaner), using that little red tube, into the latch unit. This rinses off the old sticky dirty dried out lube. Then I sprayed in a little lube like WD40. Next "flick" the outside handle a few times. Next use the key to move the lock back and forth. It took a couple of tries but the door works fine now.
same m8 mine waz da same n i did wot u did n it work ed trust him
Where is the low pressure fiting for the ac on a 1977 corvette?
Most GM AC's around that year mount the low pressure fitting on or near the receiver/dryer on the firewall. (it's the big silver tank that gets really cold when the AC is running right)
How much does a 1977 Chevy Corvette weigh?
The factory estimated them at around 3800 pounds. But owners have reported stock weights considerably lower than that, as low as 3300 pounds, depending on the options that came with the car, such as the spare tire, the amount of gas in the tank, and so on. The people who really work to reduce their car's weight have gotten down as low as 2900 pounds. And remember that reducing a car's weight is almost identical to adding horsepower :-)
Where is the fuel pump relay on a 1987 500sl?
In my 1987 560sl The fuel pump relay was directly behind the idle control module. You will need to remove the glovebox and you will see three modules. The one I replaced was the "KVS Kickdown" part number 002 545 16 05 about $20 on eBay for oem used. All the parts places called out a different PN . They may have went to a different number, the new one has more pins I did not try to fit one.
What happens to the fuel pump in a 1993 corvette if it runs out of gas?
The fuel pump is located in the fuel tank and is cooled by the fuel. If you ran out of gas it could cause the fuel pump to overheat and burn out.
How do you install a starter in a 1979 Corvettee?
Disconnect the battery. Get the car up off the ground with alift or a jack and jack stands. Never work under a car supported solely by a jack. Unhook all the wires. Unscrew the two mounting bolts [9/16] and drop starter down. You may or may not need to remove the metal dust cover. Installation is in reverse order.
