0
Dodge Intrepid
In this category you can ask questions about Dodge Intrepids. These questions can include where to find parts, how to get help, or how to do it yourself.
1,915 Questions
How do you replace window clip of Dodge Intrepid?
Answer
THIS BULLETIN SUPERCEDES TECHNICAL SERVICE BULLETIN 23-11-95, DATED
MARCH 10, 1995, WHICH SHOULD BE REMOVED FROM YOUR FILES AND NOTED
IN THE 1995 TECHNICAL SERVICE BULLETIN MANUAL (PUBLICATION NO.
81-699-96084). ALL REVISIONS ARE HIGHLIGHTED WITH **ASTERISKS** AND
INCLUDE ADDITIONAL MODEL YEARS AND PART NUMBER CHANGE.
SUBJECT:
Door Glass Lift Plate Service
OVERVIEW:
This bulletin involves replacing door glass lift plates.
MODELS:
1993 - **2001** (LH) Concorde/Intrepid/LHS/
New Yorker/Vision/300M
DISCUSSION:
Door glass lift plates are now serviced separately from the glass. Anytime the door glass is
intact and the lift plate(s) is worn or damaged, perform the repair procedure.
PARTS REQUIRED:
AR(2) **04878907AA** Lift Plate, Door Glass
AR NPN Urethane Windshield Sealer (3M p/n
08609 or Equivalent)
REPAIR PROCEDURE:
THIS REPAIR IS COMPATIBLE WITH DAIMLERCHRYSLER'S MOBILE
SERVICE PROGRAM AND DOES NOT REQUIRE HOISTS OR OTHER
FULL SERVICE FACILITY SPECIAL EQUIPMENT.
1. Remove door trim panel and upper trim retainer channel.
2. Connect power window switch and lower window to 50 mm (2 in.)
3. Loosen screws holding regulator roller channel to glass.
4. Slide roller channel rearward to allow screw heads to pass through key slots in channel.
5. Separate glass from roller channel.
6. Raise glass upward and out of opening at top of door.
7. Mark location of liftplate(s) on glass.
8. Heat lift plate with propane torch or heat gun to soften urethane and pry lift plate from
glass by inserting flat screw driver between edge of glass and plate.
23-039-00 -2-
9. Clean any remaining urethane from glass surface.
10. Apply urethane windshield sealer to channel in new lift plate.
11. Push and/or tap plate onto glass in the previously marked position.
12. Allow urethane to harden for at least 12 hours before operating window (longer times are
required if temperature is below 50 degrees F.).
NOTE: URETHANE SHOULD SET FOR 1 HOUR BEFORE HANDLING/INSTALLING
THE GLASS. THE REMAINING CURE TIME CAN BE ACHIEVED IF THE WINDOW IS
INSTALLED AND LOCKED IN THE UP POSITION FOR THE SPECIFIED TIME. THIS
WILL ALLOW THE VEHICLE TO BE RETURNED TO THE CUSTOMER WITH THE
WINDOW HANDLE OR SWITCH TAPED TO PREVENT USE.
13. Reverse removal instructions to install glass in door.
How do you remove the dash plate in a 98 Dodge Intrepid?
The dash plate just pulls out, if that makes sense. Just be careful not to scratch the dash itself when you take it out. To get to it, you'll have to take the cover off the steering column. This plate (if this is the one that surrounds the gauges, you'll want to pop it loose with something plastic, like a spoon or your fingers.There are two or three screws that hold that on. Make sure the retainers are inside the holes before you snap it back in. Good luck.
Where is the output vehicle speed sensor on a 2001 Dodge Intrepid 2.7?
speed sensor is on the transmission use a 1 inch wrench and it is the rear one closest to the rear bumper the switch is plastic and cost about 20 from the dealer is car staying in second gear and speedometer not working? this is what happens when speed sensor is bad should take about 10 minutes to change including time to jack up front end
Where is the LDP leak detection pump on a 2001 dodge neon?
Standing at the rear of the car looking forward the ldp is located on the passenger side of the car right behind the gas tank, on the inside frame just to the left of the rear wheel.
If it has the 3.5 motor, it may be a matter of bleeding the air out properly. There are several more common causes of overheating.
How do you fix a broke gas line in a Dodge Intrepid?
I assume that you have a 3.5L. if so there was a Factory Recall on this problem in the past that covered the leaking fuel rail on 3.5L. Intripid modles...check with your nearest Dodge Dealer for more info...
What does the service code P0700 mean for a 98 Dodge Grand Caravan?
Trouble code P0700 means:Transmission control system malfunction
What type of oil do you need for 95 Dodge Intrepid?
I have used 10W30 in every gasoline engine I've ever owned and never had a problem. Although in my climate it never gets below -10 F or above 110 F.
What would cause a 1997 Dodge Intrepid smoke?
Could be a bad head gasket. You would get engine oil leaking into the cylinder heads and that would show as smoke out the tail pipe.
What type of transmission is in a 1993 Dodge Intrepid with a 3.5L engine?
It is called a 42LE or an A606
How do you remove the fuel filter located on a 1997 Dodge Intrepid 3.5L?
To remove the fuel filter on your 1997 Dodge Intrepid 3.5L, you will first need to locate it. The filter can be located on the right rear of the vehicle near the fuel line. Before removing the filter, depressurize your vehicle by following the steps in your manual. Once depressurized, you can then remove the filter using a wrench.
How much does it cost to replace CV joints in 1997 Dodge Intrepid?
well a cv joint will cost you from anywhere 50.00 to 100.00 dollars and labor will cost you about 100.00 to 125.00 give or take dapends on the mechanic. so at the most 250.00 bucks all together
How do you replace a thermostat on a 1997 Dodge Intrepid?
If you have a 3.5L engine, just follow the top radiator hose to the engine. The hose attaches to the thermostat housing. remove the 2 bolts and the thermostat is right there. Do not use the rubber ring sold with the new thermostat unless your housing is plastic. Install new thermostat with the spring facing the engine (down).
Fold down, or remove rear seat back and climb in to open from inside.
What is the life span of a Dodge Intrepid?
The way it's been going, and from the research I've done.... If you've got a 2.7L Motor, expect not to make it to about 100,000mi. Actually, from what I've seen, it's more like 75,000 UNLESS you change your oil once every 1500 miles, and git'r done with full out synthetic. Then you may get lucky... Otherwise, expect 'er to last a couple years before the motor dies out on ya... Gotta love Chrysler engineering...
What is the code 00253 for 2000 Dodge Intrepid?
I just replaced the ECM and the code went away. I was not able to read any of the sensors on the engine with the scan tool. Once the ECM was replaced, everything was OK>
What could cause a 2001 Dodge Intrepid to click when trying to start?
the solenoid on your starter is finished, replace the starter......
I have a 95 Dodge Intrepid that has the same problem. On my Dodge The circuit board is fried. Capacitors, diode and tracing burned off board. If you don't have any blown fuses. Then yours could also be fried. I Checked with the local dealer and they want $691 just for the part. https://www.trademotion.com wants $486 for it. Or you could visit your local juck yard and find one. any 93-96 Intrepid, LHS or Concorde should work, according to the dealer.
Where is the blower motor resistor located in a 1994 Dodge Intrepid?
Disconnect the negative battery cable and wait two minutes before working in the vicinity of the impact sonsors.Wait until the engine is completely cool before beginning this procedure. To access the blower resistor,carefully pull down the lower right under-dash panel.(Below the glove box)Remove the two screws and pull the blower motor resistor from the heater housing.The twisted pair of wires are the ones going to the blower motor.
Check the electrical connections on the wires. Also, make sure that the new alternator is working. It is possible to get a new one that has problems. You might have to remove it and have it checked out. i have the same problem on my intrepid i changed the alt, batt, and still light on i check both alts and the first and second are good.
What is the expansion valve on a home AC condenser unit?
The expansion valve is usually in the evaporator and simply opens or closes to allow the appropriate flow of refrigerant into the coil. The theory is that the expansion valve makes your AC run more efficiently.
Where is the oxygen sensor for a 2001 Dodge Intrepid 2.7l is there a picture of it?
i have dodge intrapid 2.7l my 02 sensor light come on p0051
