0
Dodge Ram
The Dodge Ram is a large pick-up truck produced by Chrysler from 1981 to present. The car, which features a front engine and rear/four-wheel drive, was named “Truck of the Year” three times by the Motor Trend magazine.
13,744 Questions
The manual mirrors fold back at highway speeds how do you tighten them. 96 Ram 1500?
You will have to remove the inner door panel with a screwdriver by prying it away from door. It is just held in place with plastic clips. Then remove three 10mm nuts holding your mirror to the door. With mirror removed there are 3 small torqe scres that will need to be removed, then just rotate the plastic cap out of the way and tighted the 4 slighly larger torque bits (I think the are T-25's)Just follow the reverse to put back to gether
i have 97 ram, with the same issue. after many hours of trying i ended up braking the black plastic off from around the base of the mirror. after that i found 3 screws that come in from in side the door, getting the piece of plastic off will not be EZ, but after that there are 4 screws that hold the mirror in place. a litte lock tite and an Allen wrench and you set.
What is the firing order for a 1976 dodge d100?
its 1 8 4 3 6 5 7 2
looking at it from the front of the vehicle
8 7
6 5
4 3
2 1
What happen a the throttle position sensor goes bad?
The throttle position sensor, TPS, tells the engine control module,ECM where the throttle blade is. It is the primary way that the ECM knows what you want out of the engine. There is a backup system if the TPS fails, but it is not as efficient as the TPS.
So what does happen. The engine will not be as responsive to the throttle as it should be.
When you accelerate there may be a pause while the ECM realizes what you did. If you let off the of the accelerator the engine may take a few moments to return to idle or may idle rough and have a minor surge. It will ultimately return to idle. The engine will still run, but will be sluggish and lose its pep.
What kind of mileage should a dodge ram 2500 with a 5.9 v8 gas engine get?
I get 9 MPG empty or towing a car trailer and car around town.
If I use cruise control and keep the RPM gauge below 2500 during acceloration I have gotten 14 MPG on the highway .
I would not own another truck but I would like better MPG .
1997 Dodge Ram 2500 4X4 Automatic Xtra Cab Long Bed with fiberglass cap and tools and jacks in the bed 5.9 gasoline 285/65/16 tires glass pack single exhaust.
Does the 94 dodge ram 318 magnum have adjustable timing Is it done by turning distributor?
It is zeroed to the crank with a scan tool. It can not be done with a timing light. It is done by turning the distributor.
Where do I find a fuse box diagram for a 1996 Nissan truck?
look where the hood release latch is (left of the steering wheel, below dash) just above that is a square section on the lower part of the dash. It has a handle and can be pulled off quite easily. Your fuses are contained therin and attached to the backside of the peice you pulled off will be a fuse puller, extra fuses and a fuse diagram.
This engine is computer controlled.
The computer can decide to not give you any power, usually because the computer does not know you are stepping on the fuel.
Have the car scanned and repaired.
What is Oem tires for 1996 Dodge Ram 2500?
There should be a sticker inside the driver door that tells the OE size. What will work is LT245/75/16, LT265/75/16, or if it has the 16 X 7 wheels....LT235/85/16 all sizes in no less than 10ply! Some tire sizes have their advantages. What are you using the truck for? Some tires or tread designs are only made in specific sizes.
It could be the disc brake covers on the inside of the rotor. One of mine was knocked up against the rotor and made a grindingand rattling sound that got better as I went faster. Worth a look because it's an easy fix if that is the problem! It could also be bad wheel bearings. Does it stop or change when turning? if it does, that would be another vote for bad wheel bearings.
What weight oil for a Dodge Ram 5.7?
5w30 or 5w20, it depends on the year.
5w30 or 5w20, it depends on the year.
I have the same starting problem. It came on gradually and now it to the point I need to do something about it. I believe this is caused by a clogged fuel filter, bad fuel line check valve or bad fuel pump. Regardless they are all located in the gas tank so it doesn't really matter. You can pick up the entire module at about any parts store for 250 to 300 bucks. Requires dropping the fuel tank. The heater not blowing is caused by a clogged heater coil. If you haven't changed the antifreeze in a long time some brands will gel and clog the heater. Try unhooking the lines to the heater coil and flushing it with a garden hose. If little or no water comes out its clogged. If your lucky and have decent water pressure you might be able to unclog it. If not the coil needs to be replaced. Note: unclogging the heater core with a garden hose will often work better if the hose pressure is applied to the heater core output or return line. The heater not blowing as cold as it should could also be caused by low refrigerant in the a/c system, or by a plugged condenser coil in front of the radiator (blowing air or water through it from the engine side may help).
How long does it take to swap transmissions in a dodge ram 2500 diesel truck?
Depending on the year, manual or auto, an experienced mechanic could do it in 4-8 hours.
Depending on the year, manual or auto, an experienced mechanic could do it in 4-8 hours.
How many u-joints on a 2002 dodge ram 1500 quad cab?
The front axle shaft will be cv style, so zero there.
The front drive shaft would have three.
The rear drive shaft would have two if it is a one piece shaft, three if a two piece shaft.
The front axle shaft will be cv style, so zero there.
The front drive shaft would have three.
The rear drive shaft would have two if it is a one piece shaft, three if a two piece shaft.
What is the firing order on a 1999 dodge ram 1500 V-6?
The firing order of all Dodge V6 truck engines is 1-6-5-4-3-2.
Get to the rear wheel cylinder of a dodge ram truck?
TO get to the wheel cylinder you have to romove the wheel. Then you need to pull of the brake drum. You can make it easier if you take a flat head screwdriver and pry the drum off a little bit to get it started. After pulling the drum off you will see the wheel cylinder at the top pressing against the brake shoes. Undo the 2 bolts on the back and the brake line. You might have to compress the pistons and pull the shoes apart a little bit to wiggle it free. You can also use a hammer to hit the back side of the clylinder to get it out.
