How do you change the oil in a front differential on a 2002 dodge ram 1500?
it isn't fun to pull the cover it is tight the easiest is to get some type of small hand pump and suck it out
Since I don't know what your vibration feels like, it COULD be a worn U joint (rear wheel drive only) or it could be a tire balance or bent wheel problem.
How do you know on the distributor cap which is number 1?
If you are lucky (and no one has messed with it) its written on the cap.
If not remove cap, remove #1 spark plug.
Hold thumb over spark plug hole and have a Friend "bump" the engine over about a 1/4 turn per time. (or use a remote button)
The air will puff out when the cylinder is coming up to top dead centre.
Then carefully turn the engine until the timing marks are close to lined up.
The ignition rotor will now be pointed where # 1 is. Mark and replace cap.
Where is the leak detection pump in a 99 ram 5.9L?
Not sure on the 99' but my is on the passenger side... on the top of the inner fender.
Would 23's size rims fit in a 1992 Mitsubishi mighty max truck if i lift it high?
I am positive you can run 22's with 235/30/r22 tires no mods to suspension at all if you use the nitto neo tires, Not sure about 23's though.
Where are the vacuum lines on a 2001 Dodge Ram 1500?
Both sides of the engine, some run to transfercase if equipped. Others run to ac/heater box inside dash. One runs to brake booster.
when driving it losing vac too ac till moter shifts gears
How do you take off a fan clutch for 2000 s10?
Very carefully. :) Seriously, the use of a spanner nut wrench/pin wrench is this proper way to do it. There is a tool called a pin wrench that has 2 pins that are perpendicular to the handle. The 2 pins are inserted into 2 of the 4 holes (not the bell pully bolt holes, but the 4 smaller holes that are between them) and used to hold the bell pully from rotating. Then you take the correct size wrench or LARGE adjustable wrench to turn the large nut between the fan blade and bell pully. The threads are right hand. The nut turns off in the normal direction that you would remove a nut or bolt. it takes some force. The "shade tree mechanic" way is to remove 1 of the bell pully bolts. Then find a bolt that's longer than the bell pully bolt and screw it into one of the empty hole (as far as you can) and using a pry bar jambed between the bolt and the bell pully to restrain it from turning use the wrench or LARGE adjustable wrench to unscrew the large nut. I just did this procedure while changing a head gasket on a 2000 S10 2200 engine. Good luck.
Does a catalytic converter cause the car to overheat?
It can cause this problem since you will have to work the engine much harder to get the power needed and the exhaust can not get out. If you are talking about water temperature being too high, not really. Check for a sticking thermostat on this one. More often it will cause a loss of power and if it has a carbarator it can cause spit back out of the air cleaner.
How many quarts does a 1998 Plymouth Breeze transmission hold?
It holds a total of 9 quarts. I know, because mine is going into the shop for a re-build. At 174,000+ miles, it has held up very well.
What are the 2 advantages of the hemispherical combustion chamber?
One advantage to this design is the valve diameter is increased via the valves been inclined at approximately 45 degrees, therefore giving better volumetric efficiency.
sorry only have one advantage x faye x
What would cause the speedometer not to work on a 2002 Dodge Ram 1500?
Speed senor in rear differential failed. for mine, the speed sensor broke off limited-slip gear box and broke sensor in a million pieces. Had to replace my differential.
Dodge ram 2500 5.7 liter hemi location of coolant temperature sensor?
It is next to the thermostat housing.
No not on my 2005 5.7 hemi it is under the a.c. compressor which has to be removed to replace
What is the horsepower rating on an 89 Sunfire turbo?
00 because there is no 89 sunfire turbo 89 was the sunbird
Gas mileage in 2006 Dodge Ram hemi?
10-20. depends on driving habits.
10-20. depends on driving habits.
What transmission is best to use with a 440 engine?
The 727 torqueflight automatic tranny is the only tranny to hold up to the 440 torque if your talking automatics.