0
Dodge
Dodge is a brand of automobiles, sport utility vehicles and minivans in the US, manufactured and marketed by Chrysler Group LLC in over 60 countries and territories around the world.
2,165 Questions
What is curb weight 03 dodge ram quad cab 2wd diesel?
8.3 L, 22" wheels and Pirelli tires, lowered suspension, bucket seats, body modifications, and a spoiler
What is the best cold air intake for a lancer or a short ram intake?
The AEM Cold Air Intakes work really well and gain real power that you can feel. If you click the link you can find one for your Mitsubishi Lancer. Cheers, GPI Performance
How do you remove the oil pan on a dodge ram 1500 with a 5.2L engine?
is there an illustration to show me how to remove the oil pan?
AnswerLoosen the motor mounts and jack the motor up about 3 inches. Place the jack under the harmonic balancer. also the drain plug has to be removed to clear the strainer on the oil pump.How do you change the clock on a dodge caliber?
Press and hold the button that says "clock" until the hour digit starts blinking. Use the left knob turn clockwise or counter to change the hour digit. To change the minute digit use the right knob.
What does a warning light that looks like a lightning bolt mean on a 2006 dodge ram 1500?
The computer has detected a malfunction in the electronic throttle system. You need to have it checked for codes.
The computer has detected a malfunction in the electronic throttle system. You need to have it checked for codes.
Where is the cam sensor located on a Dodge Caravan?
The cam sensor is located in the distributor. It really depends on the engine size and year. Some are in the timing covers. My 97 3.3 is- also the 3.8
Where do you add transmission fluid in a 1986 Dodge Daytona?
The transmission filler plug for a standard transmission is behind a plastic cover under the drivers side wheel well. You have to remove three screws (I think that they are 3/8 or 5/16 in), one near the strut, one near the front of the wheel well, and one underneath near the bottom left end of the radiator. Pull the cover down and place it to the side. The filler plug will be exposed. The 5-speed manual transmission takes Dexron III auto transmission fluid. Have the car parked on level ground and just fill it up to the bottom of the hole. Replace the plug. Put back the cover and replace the three screws. It helps to turn your wheels all the way to the left before doing this procedure. There is a special cap available at some stores that has a built in valve and spout for use on transmission fluid bottles. Works great. Just be sure to place it in a paper towel afterwards to soak up the fluid.
How many Dodge Lil red express trucks were made?
2,188 were produced in 1978.The production of the 1979 Dodge Lil' Red Express Truck was increased to 5,118.
Where is the tps sensor located on a 2000 dodge quad cab?
The Tire Pressure Sensors are typically attached to the backside of the valve stem (the part that's inside the tire). Where the sensor for the sensors is located...I think it's part of the 'computer' The throttle position sensor is on the throttle body opposite the throttle cables.
Where is the voltage regulator on a 1993 w 250 cummins diesel?
It is part of the computer behind the battery.
It is part of the computer behind the battery.
What is the firing order for a Dodge 5.9L V8?
Pass side 2-4-6-8
Driver side 1-3-5-7
Clockwise rotation on the distributor.
Answer1-8-4-3-6-5-7-21-8-4-3-6-5-7-2 clockwise rotation
18436572
Answer1-8-4-3-6-5-7-2How do I change injectors on a Dodge cummins?
Is the truck a 12 or 24 valve? I have never done a 24 valve but the ingectors are located under the valve cover (Top of engine w/ Cummins logo), and I immagine it would be very simmilar to a 12 valve once you get into them.
12 Valve Injector Install News Summary:
These instructions are written to help you replace injectors in your 12 valve cummins. Most of this was taken from TDR members...
News Content:
Remove Dodge Cummins....etc. plate from valve cover
Use an air gun to blow all loose material from the top of the cylinder head.
Remove the high pressure fuel line clamps (8mm wrench)
Remove the #1 valve cover. Note: this provides room to get the fuel lines out of the way while removing the injector body nut. The first three cylinder fuel lines pass between 1 and 2 valve covers.
Remove the large retainer nuts from the injectors ( 17mm wrench or deep well socket, some have used a 15/16" deepwell socket)
Remove enough fuel drain bolts and move the manifold out of the way (10 mm wrench).
Position fuel lines out of the way for each injector as you go (dont be afraid to bend them a little, but not too much!)
to get each injector out use a set of pliers (vise grips are a handy item) to grab the injector, turn and wiggle it out. Some can be difficult. I had to use some force for this step. The injector will turn some. They have a ball like a ratchet uses to hold a socket. (as you will probably notice on the new injectors)
If the injectors are hard to remove, put a nut on top of the injector where the fuel line came off and pry up; they come out easily.
if this doesn't work you can use the Cummins injector puller and all six will take about 5 minutes.
There is a "seal" where the copper washer seats and make sure there is no crud on it so the seal will be good. You have to use a light and crawl up to see down NO.'s 5 & 6.
When replacing the injector lightly oil the body insert it in the hole and rotate the injector until the notch on the side of the injector finds the depression in the head, when it is in position, the injector will not rotate any more. note:(wouldn't hurt to leave one old one installed for comparison until several new ones are down the whole way)
Put some never seeze on the injector body nut and torque the retainer nut to 44 ft-lbs.
Reinstall the lines on the pump fully (if you disconnect them)
Finger tighten the high pressure fuel line nuts on the injectors.
When you reinstall the injector drain manifold get all the little screws to start significantly before the final tightening. They crossthread easily.
Reinstall all the high pressure fuel line clamps
Reinstall the fuel drain manifold
Crank the engine until there is fuel coming out of all injector lines, then tighten the high pressure fuel nut and start the engine. It may miss and run rough for a few moments, then begin running smoothly.
Is there a Clock spring recall 2003 dodge caravan?
Call the dealer with the vin number and they can check to see if any recalls apply to your van.
How do you replace brake pads on 1996 dodge 1500?
Front wheels? Remove wheels Remove caliper mounting bolts Slide caliper off rotor Use a "C" clamp to fully compress piston into caliper body Replace inner and outer pads Re-install caliper PUMP BRAKE PEDAL TO SET PADS AGAINST ROTOR PRIOR TO MOVING VEHICLE
What does the code P0404 on a 2005 Dodge 1500 5.7 hemi mean?
Trouble code P0404 means: EGR Position Sensor Signal Performance
How do you replace a glass mirror dodge?
I took a fillet knife and ran it behind the mirror to cut the glue. Advance Auto sold the right replacement. Apply glue strips and press mirror on.
Where do you find the VIN on an engine?
The VIN on the dash will tell you everything you need to know. Engines dont have VIN's. They have casting numbers. Such as "Block Casting Number" or a "Head Casting Number" or a certain/specialized part number. But on old cars this maybe different and I stand corrected.
^^
This is correct, even for old cars. The block or head casting numbers will tell you the "type" of vehicle the engine was designed for but not the specific VIN is was installed in.
Some blocks have numbers for destined for "crate" which means it was not installed in a vehicle, but used as a replacement motor. For US engines, the block number will usually narrow your search down to a 5-10 year block and the type, such as truck or car. Special vehicles, like Corvettes and such, will have specific numbers (because they used aluminum and high performance parts) so the search will narrow down further.
Where can I Find a wiring diagram for a 1979 dodge ramcharger?
You might want to try ramchargercentral.com I know there are several guys on there that have multitudes of wiring diagrams for many different years. check the pics section usually tons of em in there.
The fuel system is capable of withstanding the corrosive aspects of the higher ethanol concentration and the computer is programmed with calibrations for running on E85 on the flex fuel system. The engine itself is no different.
How much horsepower can a 1994 Dodge 318 engine produce?
How much money are you willing to spend? 400 H.P. is easily attainable with enough money. Up to 700 H.P. is possible.
