0
Electronics
Electronics are a branch of technology and science that deals with the control of the flow of electrons.
3,725 Questions
Where can you find the electronic control module on a 1977 Cadillac Seville?
Should find ECM just under center dash below radio and climate control panel
100 WVDC means 100 working volts DC. That is the maximum operating voltage that the capacitor is certified to have across it. Exceeding that rating could puncture a hole in the dielectric, leading to catastrophic failure of the capacitor.
What is manual and electronic recording?
today, most transactions are recorded electronically because they are processed either by an electronic cash register or by computer.
the benefit of recording transactions electronically - such a itemised receipts issued by a supermarket. in addition, any electronic system is usually liked to the firm's computer system. this means that information is immediately entered into the relevant accounts and managers can obtain reports that summarise this information.
manual recording are only kept by businesses that would not find it worthwhile to buy a cash register or use a computer system. an estate agent mat act an an agent for rental property, only collect a few rents each month and find it easier to record these manually. a taxi driver will issue manual receipts to the passengers who want to reclaim money from their employer and tradesman who deal in small cash amounts, such as window cleaners, are also likely to keep manual records
by abdul, (15)
Can you use the same apple ID on 2 iPods?
Yes you can use the same ID.
It's not a good idea to let someone else use your ID though as they will be able to use your details to pay for apps etc. If you, yourself, have two iPods and wish to use the same ID then this is a lot safer.
CD-ROM works on the principle of the LASER and it is a major application of the LASER
How do you program casio fx-88op?
A Casio FX-88OP is a scientific calculator. To program this, simply run the program in the true MS-DOS mode. Do not use an MS-DOS prompt.
When admission open for engineering in dawood university for session 2012?
Dear the admissioNs in DCET,karachi will start in december 2012 . It is expected that the prospective wil b available aftr 10th f dec 2012 . Fr More infrm 03414721557
Your Acer is freezing when you turn it on how do you stop it from freezing?
Turn it off then turn it off to temporarily unfreeze it.
How can you know your SSC Registration number through Internet?
Sir maine ek form online kiya tha clerk/data entry operator jiska date of Birth 17/10/1987 hai or Date 14/09/2011 hai Name Harshna, sir ji maine Registration ID Galat note ki hai please Give me correct Registraion ID
What type of energy do electronics use?
Electronics circuits and devices are operate on D.C power supply. But the source of D.C power are mostly batteries and rectifiers. Batteries are really deliver pure D.C supply but they are bulkier and big in size. So we use rectifier circuit for operating Electronic devices. sometimes where backup of supply is needed there both source may present for example in laptops there batteries and rectifier(adapter) both are used.
Is the at 19 waterproof action camera waterproof?
If they say its waterproof then im pretty sure its waterproof , they would'nt say that it is waterproof if it isn't cause then they will be getting all those waterproof camera's back!
What are the inventions in the year 1990?
Auto molds were invented in the 1990s.
Molding materials commonly used are: phenolic, alkyd resin, diallyl phthalate, melanmines, and urea. These resins are available in the form of fine powders, granules, flakes and rope. They are also available as PREFORMS(in a perform the specified amount of resin is compressed and sticks together like an aspirin tablet). A perform contains just enough resin to fill the mold and to allow for a slight flash ( extraplastic attached to molding along parting line which must be removed before the part is completed). Plastics pastes or rope pre-weighed into slugs, are used the same way. the moulkd shop is very good. the web is www.freetech-mould.com
In compression molding a charge of resin is placed in an open two-part heated mold. The mold is then closed. Pressures from 1000 to 10000 psi are applied by a hydraulic press. Mold temperatures which range from 280 to 400 F, cause the resin to melt and flow through the openings of the mold cavity. When polymerization is complete, which takes from 3 to 20 min. The mold is opened and the product is removed. Mold temperatures can be maintained and the product removed hot as the thermosetting material is in a solid state. The next charge can be placed in the mold immediately.
The mold for compression molding can be a single or multiple cavity type. Molds are usually made of tool steel and are highly polished to produce the desired product finish. The mold halves are bolted to the upper and lower platens of the hydraulic press form automatic opening and closing during the molding cycle.
If the molding process is manually operated, the operator prepares the charge, loads the molds, removes the molded product and often trims the flash during the cure period. Compression molding done on automatic presses requires a cycle in which the molding compound is fed directly into each mold cavity, compressed, cured, and the product ejected from the press. If inserts are required in the product they are usually placed in the open mold by the machine operator.
Can police track a computer that's off?
No. without a signal it is impossible. If a stolen computer is turned on though, that is the only way the signal can be found. Same thing with cell phones.
How do you open a Pelonis tower fan model TWS5 for cleaning?
First, an obvious but vital safety warning: Unplug the fan.
1. Remove two rubber plugs on the upper part of the rear panel to expose two Phillips head screws, and remove them.
2. Remove fan's base to expose the fan's drive shaft, and remove the C-clip, two washers, and the oscillation armature
3. Remove two Phillips head screws to the rear (in the two plastic holes)
4. Push inward on both sides half way down the rear panel and remove the rear cover
If you wish to tear it down further, it is a fairly straight forward combination of screws.
A survey of 1353 American households found that 18 percent of the households own a computer?
i can almost garienty you that i could answer that quistion, if it was a quistion.
Can you get a HDMI and RWY Splitter?
rwy cables are much better known as RCA cables. search for hdmi to RCA, you should find some on eBay for about 5 bucks.
What are the names of some companies that specialize in electronic assembly?
There are a number of companies that specialize in electronic assembly. Some of those companies include 'Fampec Technology', 'Sunstone Circuits', 'Smile Electronics' and 'GlobalSpec Electronics'.
ibby laksar does it and he eats handesh while doing it
Hey I was given an old computer a while back and used it for casual on of gaming, I recently decided to build a custom PC so i started learning what i need to do and how i can pick my parts, with not a hole lot of money to spend at the moment i think i will start by doing my build in gradual bits over say a few months or so. I just wanted to know if it is worth it upgrading the GPU, power supply and case that i already have and putting a new one into the current system i am running then doing the mother board, CPU, RAM, and liquid cooling later. At the moment it has a AMD Athlon(tm) II X4 640 3.00GHz, in a Gigabyte GA-MA785GMT-UD2H with a EAH5450 SILENT/DI/512MD2(LP). Thanks, Ben
