Ford Fiesta

Need serial number first.

The 2014 Ford Fiesta runs on regular unleaded.

THE FORD GUY SAYS` It will be your cps or crankshaft position sensor, its a magnetic sensor and picks up particles from the clutch (bit like a screwdriver in iron filings) causing juddering, remove clean replace. should fix problem, dont take it to garage as they will replace at cost of part £65+vat and labor, have a go i bet its covered! good luck THE FORD GUY SAYS` It will be your cps or crankshaft position sensor, its a magnetic sensor and picks up particles from the clutch (bit like a screwdriver in iron filings) causing juddering, remove clean replace. should fix problem, dont take it to garage as they will replace at cost of part £65+vat and labor, have a go i bet its covered! good luck

On my '06' it's in the glove box in behind.

Look for the build sheet sticker usually found on the glove compartment door.

It runs from the clocks in the dash all the way to the gearbox where it screws into the box at the rear just above the diff housing.

Once you know how it is amazingly simple, and is probably within the capability of most DIY mechanics. I was told it might involve £80 labour costs. The part cost me approx £42 inc UK VAT in September 2009. They are sometimes advertised on Ebay. Watch out when buying that the parts are 'handed', so you need to know if you need a nearside or offside replacement. This is how I did mine. You will need: a. a couple of flat ended screwdrivers with fairly blunt ends (ie to not cut fabric).

b. a torx screw bit to fit the screws in the rear of the seat.

c. a torx screw bit to fit the two bolts which hold the internal latch in place. 1. Using the screwdrivers, gently remove the plastic fascia which covers the top of the rocking release mechanism. It is just clipped on! 2. This will expose the rocking release mechanism and its surround. 3. If your seat is not 'locked on' then ignore 3. If your seat is 'locked on' then apply gentle pressure to the SIDE of the rocking release BETWEEN the mechanism and its surround. Lifting the rocking release mechanism will then expose the inside of the device. You should then be able to hook & pull up a plastic rod with a piece of string or similar and the seat will 'unlock' and tilt forward. 4. Now remove the torx bolts which attach the seat to the car floor and move it to the back of the car, face down for ease of working. 5. The fabric in the area of the latch now has to be gently removed. 6. Gently pull the fabric near the latch mechanism out of the groove which surrounds the seat back. THIS IS NOT EASY as it is held in place by a spring around the perimeter of the fabric. As you pull it starts to slip back again, so use a flat bladed screwdriver to help stop it slipping back into the groove whilst you renew your grip. Its a bit like removing the inner tube from a bicycle. A friend 'sharing the load' with a couple of screwdrivers makes life easier, but you need someone who values your car more than you do. Mr/Mrs/Mz,Miss Bigmusclesnobrain is not what you need! This is the most delicate part of the task! 7. Your aim is to only remove enough of the fabric from the groove to give limited access to the two torx screws which hold the mechanism in the seat. Don't do any more than you have to, and certainly don't go round the top of the seat. Six inches is plenty! :>)) 8. With care, the heads of the two torx bolts will now be visible and the fabric will remain intact. After undoing the two torx bolts you can carefully remove the mechanism from the top of the seat. 9. Now feed in the new mechanism from the top of the seat and fix in place using the two torx bolts. Try not to trap the fabric between the top of the seat and the new fitting. 10. You did watch how the fabric 'spring' fitted in the groove in the back of the seat didn't you? Well now is the time to refit it and smooth it down. This is easier if you have only pulled out a small length! 11. Now refit the seat to the floor and tighten the torx bolts. 12. Carefully lock the seat in place. 13. Now check that the seat locks back firmly and correctly! A seat which tilts forward in an accident is not the aim for this project! 14 Now fit the plastic fascia to the top of the seat. PLEASE DON'T ATTEMPT THIS IF YOU HAVE ANY DOUBTS ABOUT YOUR ABILITY. SAFETY IS PARAMOUNT!

in the steering wheel

Behind the glovebox hope this helps

it is a 1.3 litre which is 81 cid

1.1 litre = 1,100cc

To replace the mirror glass on a Ford Fiesta first remove the clips holding the mirror in place and remove the glass. Next, heat the adhesives with a hair dryer or hot gun and use a putty knife to remove the adhesive from the mirror housing. Add glue to the corners and put in new mirror. Press the mirror into place for one minute and replace the clips.

Under the bonnet, under the heater motor filter. It's difficult to get to and requires removing the filter unit. Mk4

Depends what year it is, some have a separate dipstick and others are just stupid and you have to pull out your speedo cable to refill them i have a 98 model and you have to unscrew the speedo cable, remove the cable from the casing and then pull the entire gear shaft out of the spedo cable housing before you can even check the oil

Remove battery connections. remove large wire at starter (13mm nut), remove small wire on starter (10mm nut), remove 3 13mm bolts from the starter to the engine (some had a bracket, depends on model) starter should drop out bottom. refitt in reverse. .

The 2012 Ford Fiesta has a 5-speed manual.

really common fault is blown injector seals, are you getting any unwanted noises from the engine? any change in perfomance?

Where do you think the play is,it could be anywhere along the steering system.But try the ball joints on the steering rack,the u/v joint on the steering rack to steering column.And also watch for u/v joint on the inside of the bulk head on the steering column.and bearings on the steering column behind the steering wheel all points of wear.

The 2013 Ford Fiesta has double overhead cam (DOHC).

how much will it cost for the clutch for my 03 ford fiesta finesse please i need a price thanks

Depends on the engine. The Mk 6 Fiesta was fitted with a variety of different petrol engines and a diesel option. Many petrol engines (but not all) take a bit less than 4 litres of oil, so a 4L pack will leave a bit for topping-up. The 1.4Tdci requires just over 4 litres, so you need to buy a 5L pack. If you are not sure which engine you've got, buy a 5L pack to be on the safe side.

Fiesta dinnerware was founded in 1927 by Homer Laughlin. It was introduced to the public in 1936, and produced through 1972 when it was retired. Fiestaware was reintroduced through reproduction in 1985, and continues to be produced today.

Problem with plug shorting?

If you're talking about the safety cut-off, it's usually in the "trunk" area, on the left-hand side. Push the red button on top to activate it.