0
GMC Yukon
The GMC Yukon is a full-size sport utility vehicle manufactured by General Motors from 1992 to the present. The car is available as either a two-door or a four-door model. It features a front engine and a rear/four-wheel drive.
1,653 Questions
Why does a 2001 GMC Yukon and idle at 200-500 RPM like it wants to turn off?
I found out with my Yukon that it needed a new IAC (Idle Air Control) Valve. The first timeit happened to me the dealership only cleaned it without replacing it, but it did it again, and I replaced it myself. Idles a great deal better now and doesn't sputter or idle down. Try that.
AnswerI own a 2001 Yukon Denali w/a 6.0 Litre. Basically the same problem. Believe it or not, fuel injector cleaners are not enough to correct this problem. Pull the air intake hose off the front of the throttle body & use spray THROTTLE BODY cleaner NOT CARB CLEANER. Works like a charm!! Drive for a couple days & repeat. This is a very common problem on all Yukon's & Tahoes..Good Luck!!!
Thank you for the help I went with the Throttle body cleaner trick Worked like a charm gave me just enough rpm to keep the idle smooth and saved me alot of money for the Idle control valve
How do you replace the water pump on a 1999 gmc Yukon?
need to know how to take fan off a 97 GMC 1500 truck to replace water pump
I've done this before it's not to tough! Start by removing the plastic fan grad between the engine and radiator. Drain coolant from the radiator, about 2 to 3 gallons, and keep it contained for possible reuse. Note it is a good idea to put some cardboard on the radiator to protect it from damage by wrenches falling, a pizza box unfolded flat works good. Remove the fan blade by using a big crescent wrench to grab that large hex nut between the fan blade and the water pump; hold on tightly to the fan belt on the pulley of the water pump as you jerk your wrench handle. One spin the fan off. Remove your fan belt- But 1st draw a diagram of the fan belt and how it connects to all the pulleys on the engine so you can put it back on. Unbolt the pulley wheel from the water pump. Put a bucket or pan under the water pump to catch more before you loosen all the bolts that hold it on the block. Once drained and unbolted remove the old pump. Scrape the engine clean at the 2 ports the pump bolts to. Use new gaskets and RTV Silicone glue on both faces of the gaskets. Bolt the new pump on your engine and reassemble all the rest in reverse order. Be sure to get the coolant level back up to Parr and before you go driving dabble check everything and let the engine idle for 10 minuets to check for leaks. Be safe and I hope this did the trick for you!
What should the timing be on a 1992 gmc Yukon 57 tbi after disconnecting the computer?
The timing should be set at 0 degrees.
Where is the iac valve on the Denali located?
Depending on the year (01 and up) some don't have an IAC. It's built into the throttle body design to regulate the idle. If you have idle problems try cleaning the T body good.
Where is the evap canister in a 2005 Impala?
The canister should be under the impala on the same side as the fuel filler pipe. The charcoal filled unit holds fuel vapors.
How do you change the cabin air filter in 2006 GMC Yukon?
There is no cabin air filter on the 2006 year model of the GMC Yukons and Denalis.
Was there ever a problem with uneven rear brake pad wear on a 2004 GMC Yukon?
There was never a recall issue or a major problem with uneven brake pad wear on the 2004 GMC Yukon. This can sometimes be a caliper issue, a driving issue, or even a brake assembly issue but it is not a common problem.
Where do you fill the wiper fluid for the rear window on a 2000 gm Yukon?
under the hood. one reservoir serves both front and rear washers
What is the front head room in the 2005 GMC Yukon-XL?
The 2005 GMC Yukon-XL has 40.7 in. of front head room.
Can you convert an all wheel drive to a two wheel drive?
No. A "all wheel drive" is all the time four wheel drive. A 4x4 or 4-wheel drive can be set to drive in two wheel drive or four wheel drive.
The GMC Yukon is an American made car. The GMC Yukon is made at the Arlington Assembly plant in Arlington, Texas.
Where is the fuel filter on a 2003 Yukon XL located?
The fuel filter is located underneath the vehicle, driver side, almost under the driver seat. You can't miss it, just follow the gas lines coming from the fuel tank.
How do you take off a 2004 Yukon dashboard?
You have to bring your mom outside. Have her wipe her butt all over it. It will turn out to be slippery enough to come off.
What kind of headers can you install on your 95 Yukon that won't mess up for the smog check?
You might want to double check, but GM was using "Header-Like" exhaust manifolds from the factory. If that's the case, you won't get much improvement by putting on headers.
What kind of transmission does the 2011 GMC Yukon have?
The 2011 GMC Yukon has a 6-speed shiftable automatic.
What is a reducer in a food chain?
A reducer completes the food chain or actually the cycle. Reducers, or decomposers, decompose the dead animals or dead plants, releasing minerals into the soil.
Replace headlight bulb 2007 GMC sierra?
Assuming you have the new body style, on the drivers side you simply reach in and twist the headlamp 1/4 turn, the bulb will pop out. Replace and reinsert. Be careful not to touch the new bulb with your fingers, it will leave your body oil which will create a hot spot and shorten the life of the bulb. If you should touch it, clean it with rubbing alcohol.
On the passenger side, you have to pull the lid off the air cleaner which should give you enough room to reach in and perform the same process as the driver side.
Both sides are a little tight, but it is doable.
How do you disable the abs on 1999 Yukon?
under the hood on the left side facing forward,you will see the fuse box,remove the top ,look under the top cap you will see the location of the 50 amp abs fuse,just pull it out and then its back to standard brakes(not recommended in winter)
What would cause a turn signal to blink fast?
There are at least a couple more possible cause for a rapid cyclic rate.
1. A high resistance ["partial"] short circuit in the circuit for the turn signals. Some examples being a wire pinched in a crevice in the sheet metal resulting in damage to the wire insulation allwing a very miniscule contact between the wire and the grounded sheet metal, or corrosion build up in one or all of the bulb sockets.
2. If a replacement bulb was the incorrect bulb, having a heavier filiment than the proper bulb, it would draw more current, possibly a lot, as the change of flash rate is dependent on current value. The heavier the filiment, the greater the current draw, the greater the current draw, the greater the flash rate.
3. Oh, there is another, but you didn't mention it, so it may not apply. The more bulbs which are on the circuit drawing current, the faster the rate. A very good example is when towing a trailer with lights plugged into your vehicle's light system. The additional "load" created by the larger number of bulb filiments burning, can cause the flash rate to be incredibly fast. For this problem, a "heavy duty" flasher module is made, and sold at most auto parts stores.
