0
Honda Del Sol
The Honda Civic CRX del Sol was a front wheel drive, 2-seater, front-engine convertible produced by Honda between 1992 and 1998. Derived from the CRX platform, the car was a replacement to the famous Honda CR-X.
341 Questions
What is the bolt pattern for Honda Del Sol wheels?
4 bolts by 100 milimeters. the sockets are 12 mm x 1.5.. high offset CB 56.1
Where is the power window control module Honda Del Sol?
located under the indash.. right side where your gas pedals are. have to open carpet. black box
What is the 1994 Honda Del Sol fuse panel layout?
when you pull out the pannel and it shows you what fuse is for what.
How do you adjust the clutch in a 1994 Honda Del Sol?
The real question is "what are you trying to adjust?"
If you are looking to make your clutch petal shorter IE like a sport performance clutch you need a "quick clutch" master cylinder. Omni Power Performance has one of the best ones IMHO.
If you are looking to change the engagement point well forget it, the engagement point is based of that master cylinder, if you get a quick clutch, you are either engaged (petal out) or disengaged (petal in). A standard master cylinder gives leeway on the engagement point based on the amount of fluid being pushed through the cylinder.
Standard Master Cylinder Piston Size = About 15cm
Omni Power Master Cylinder Piston Size = About 22
What is the max height to ride comfortably in a Honda Del Sol?
my husband is 6'4" and drives comfortably
How many kilometers Honda CRV runs after gas bulb lits?
There is no standard answer to this question since the variance can be so great and is so depenednet on MANY factors. I have a CR-V and personally I would not drive farther than my vehicle will normally travel on one gallon of gasoline.
How do you take a emergency brake off of a 94 Honda Civic?
If you mean the handle itself:
Unscrew the center console pieces, you'll have to start with the back and work forward.
From there it should be straightforward, there are some screws holding down the handle as well as some tension bolts on the cable itself.
Probably it cost you just to install like not more than $500 in the shop unless you know somebody will do for you. but if you want make it cheap try to shop around and one thing try to find a tranny first so it make more cheap usually you fin this in some junk yard and also you need to find a clucth cilinder and a clucth pedal.
AnswerThis is a daunting task. You would for sure need a donor car for parts. The price of the parts would be way more than the car is worth, without a wrecked donor vehicle. I have did this in the past and would advice against it. Sell this car and buy one with a manual. AnswerIt would be easier to get a new motor entirely.
The parts incorporated with the transmission include: clutch, clutch pedal, clutch cylinder, shift linkage, air intake, solenoids, header, ECU, and throttle.
At this point all you'll have left from the original is the block, and will have spent countless hours on it, just buy a donor car with a manual and swap the whole thing.
If you're interested in things like this i would suggest going to honda-tech forums, they're very informative and helpful
How do you wire a after market radio into your 1993 Honda Del Sol?
The easiest way is to buy a wiring harness. Then you don't have to worry about touching the wrong wires.
How do you replace the oil pan in a Honda Del Sol?
I replaced the oil pan gasket, so it should be same procedure. You'll need to:
1. remove connection in the exhaust pipe location that has two springs. This give you clearance to access oil pan nuts.
2. remove a couple of brace bars that are in the way of the oil pan nuts.
3. Remove the exhaust manifold and header
4. remove all the nuts and bolts from the oil pan
5. have a new gasket and oil pan in place; and make sure you have a gasket adhesive or sealer (honda bond?)
6. Install everything back, and don't have any extra nuts and bolts.
Which fuse is for the fuel pump on a Honda Del Sol?
the fuel pump relay is under the dash on the drivers side,it looks red and gray.hope this helped .
JESUS CHrist Saves!!!
What is the stock tire size Honda Del Sol 1997?
Should be 13" for the S and Si models, 14" for the vTec.
Where is the turbo waste gate actuator located at on a 1994 Chevy silverado 3500 diesel?
It's right there mounted to the turbo itself....
What type of oil does Honda Del Sol use?
5w-30 unless you live in extreme heat or cold, in which case you'll want either 10w-30 or 5w-20
What engine is in your 1997 Honda Del Sol?
Canadian eg2 Del Sol Dohc VTEC have B16A2 direct from Japan with the same spec
Can you replace a Honda Del Sol roof handle?
Yes.
It's called a Targa Top handle.
Just a screw will remove or replace it.
You can order aftermarket custom Aluminum handles online - will last you a lifetime!
Knocking noise over front tire at low speeds?
I had a problem similar to this in my '93. I took the wheel off, and looked at the shield on the engine side of the brake rotor. Turns out, it had gotten bent and was rubbing against the brake rotor and sounded like it was knocking at low speeds. Just get some needle noise pliers, a rag, and a hammer, and gently try and bend the shield back. Use the rag under the hammer so you don't dent up the shield.
What is being bored 030 over mean?
your pistons have a certain size to them, if you happen to wear down your head and looking for a cheep fix you can "bore" (like making a hole bigger) by a certain amount and fit new pistons in, that way you don't have warped piston walls and ensure proper combustion. Also some Honda enthusiasts will bore the head and put in high compression or low compression pistons to either get more hp naturally aspirated or more hp for a turbo setup.
It has nothing to do with the heads, you don't "bore the heads"
its the cylinder walls inside the block that get worn allowing them to become out of "round" oval shaped... this will cause the piston rings to not "seat" well, this in turn allows oil to pass by the rings causing the engine to burn oil. you have the boring part right but it is NOT a cheap fix. by the time you get the machine (boring) work done and buy over sized piston's, rings and all the gaskets and if you hire someone to do it, you're better off to buy an engine, on the other hand if you want to save the labor and enjoy doing it yourself, well.. that's why most people would opt to "bore and rebuild" an engine..
to answer the original question .030 refers to "thirty thousands" over the original bore
Power antenna removal on 1993 Honda Del Sol?
This link should help you:
http://www.dstuning.com/How%20To%20-%20Install%20Aftermarket%20Antenna.asp
It has step by step procedures and pictures too
