0
Machinery and Tools
The Machinery and Tools category covers questions regarding hand tools, power tools, workshop machinery (such as lathes, milling machines, etc), welding and cutting tools and equipment, measuring instruments, earth-moving machinery, furnaces, factory and industrial machinery.
1,597 Questions
There are all kinds of rope. Some is relatively useless and some are extremely good and durable. In rope, you basically get what you pay for. Cheap rope is inevitably junk.
I think it would be a safe bet that ALL Hilti tools and systems are patented.
How do you find the tension of a rope?
It depends on where the rope is:
e.g. if an object is attached to a ceiling with a rope and we disregard the buoyancy force of air (in small cases we usually can) then F(tension)=mg(weight) but if its in a liquid being tied down to the floor then F(tension)=F(buoyancy)-mg(weight)- --> F(buoyancy) = ρ(density of the fluid)*V(the volume of the part of the object that is immersed in the liquid)*g
Naturally there are much more complex examples but these are the most common ones early in your physics education.
Socket wrench size for oil drain bolt?
Oil drain bolts on most vehicles vary from 7/16 to 5/8. Take a crescent wrench under with you to check, then compare the size to a regular socket and use it.
How many gears to a lathe machine?
It depends on the brand. A lathe could be supplied with anything from two to seven separate interchangeable gears for thread cutting purposes.
If you are asking how many gears a single standard center lathe has in total, the number could exceed fifty.
Where is the drive plate on a lathe?
Using a drive plate on a lathe requires removing the chuck and the drive plate is attached in its place onto the spindle.
What is difference between tool and weapon?
Although many tools may be used as weapons, any object that persists in the category of things intended for use in threatening, harming, debilitating or killing either people or sentient creatures would be called a weapon. This excludes tools like chisels or scissors that can be used as weapons since their use as weapons would not usually persist through time. An object such as a rifle can be used for other purposes; however, its main purpose, as a weapon, persists through time.
What is the difference between bridge wall and bridge wall temperature in furnaces?
Bridge wall is wall between rows of tube. Usually in box heater.
Bridge wall temperatur in temperatur leaving radiant section after heating radiant tube before heating convection tube.
How do you use a hydraulic torque wrench?
It is just simple, find the exact socket for the bolt-nut, once fixing them just hit the button for progress. There might be several press as per the requirement. Setting the torque range is really very important. You need to select the required range by selecting them pressure table provided with the wrench. Choose the exact pressure required and proceed further. This is highly enough to know how to use a hydraulic torque wrench.
Where would goods such as furnaces be situated on the goods and services continuum?
Goods such as furnaces, which require accompanying services such as delivery and installation, are situated toward the pure goods end.
How to calculate the ms square hollow section tube with example?
convert the tubes dimensions into linear measurement's using Pi and then the volumetric calculations become much more obvious. Mike Webster.
What size socket do you need to remove the hub nut on a 2004 Chevy pickup?
I think that is a 1 and 1/4 socket.
What is the horse's lead rope?
A horses lead rope is a rope usually between 4 and 10 feet long with a clip on the end used to attach it to the horses halter and lead the horse around.
What is the proper way to store a torque wrench?
Preferably in a box or tray where it will not get damaged.
What media can still be used for effective learning in schools?
Chalk is a good start, then computers with projectors. Televisions can also be used for educational programs, and newspapers and magazines can be used, too.
What does it mean by the crown of the weld?
The crown of the weld is the material of the filler metal that projects above the surface of the parts being joined by the weld.
