Mazda 3

On the 2007/2008 model, it's halfway up the back of the engine.

You need to access it from underneath after removing the plastic cover.

The timing chain only needs to be replaced if it becomes loose (You would hear a clicking noise under the hood when the engine is running) have that noise inspected right away if you hear it and it may need a timing chain. But not for a very very long time. Around 150,000-200,000 miles most likely.

all relays are located under the hood behind the air filter. pop the top you will see these black square fuse like. my Mazda 3 2004 all 5 of them are the same relay, so you can swap one with another to see it that cures the problem. mark each one before you swap them, so you can put them back in order just in case.good luck

z5 (1.5) and bp (1.8) engine Ron 93+, 2.0l v6 Ron 95+

They can tell you that at any automotive store!! So, when you go to buy it, ask them!

2WD Total Trailer Weight (Sum of weights of the trailer, its load, trailer hitch, vehicle passengers and what you have in the vehicle) is 4500 pounds. If you do not have the transmission cooler it is only rated for 2600 pounds. Suggest that you install a transmission cooler and carry the conventional spare tire.

I do not believe it is. I know the stock stereo from the 2006 Mazda 3 does not support mp3 cds.

this guid is refferencing a LEFTSIDE DRIVE. open your glove box. pull on the bottom of the dash strip. be gentle with this. work your way towards the left removing the strip. the right side should still be connected. if its not, you may have broken it all ready. use your fingers for this. not a screwdriver. once the strip is mostly out pull the whole thing to the left (away from the glove box) and remove it. the radio has two screws on the top of it. remove them. the small screen is connected to the radio. be careful not to break it. the rest of the radio is clipped in. gently pull and tug to get it out.

Fuel pump is located in the fuel tank. It is mounted at the top of the tank and accessible with the rear seat removed. It also has an integral fuel filter built into it. Speedycarparts.com is a good source for low cost replacement if necessary.

I bought my tires on tirerack.com for about $ 263.00. The shop charged $ $14.00 per tire for mounting.

Do not touch the glass on new bulb because the oil on your fingers can make bulb burn out. Open hood, locate plastic connector that goes into head light assembly, turn to left to remove, swap bulbs, replace into headlight assembly.

how to remove a tire on 04 mazda3 bolts are off and tire wont come off

4.5 quarts to be exact 4 quarts

You have a brand new vehicle. Look in your owner's manual. 5w-20, i suggest you get it done from the dealer, your car is too new. If u wanna DIY, at least get the oil from the dealer. Play it safe... Good luck

it is hard to get to.. say your sitting in the passanger seat and it is located behind the lower left pannel by your feet.. now to get to it... you have to remove the glove box then the panels on the side then the ECU and the cabins will be in a slot...

look on the inside of your drivers side door it will tell ya if not repost the question and ill check mine

Try this link:

http://www.mazdaclub.net/mz3ws/esicont/en/srvc/html/node_S01_1263.html

i would recommend is that u take the hud off and get one that would fit

My 2007 Mazda 3 has good instructions in the owner's manual, so assuming the 2005 also does, refer to it. See sources and related links below for more information on bulbs.

The Mazda 3 is front wheel drive.

Flywheel 79.7ft lbs - 85.5 ft lbs

pressure plate 18.5 - 24.4 ft lbs

The 2.0 and 2.3L four-cylinder MZR engines both have timing chains according to the owners' manual for my 2008. I can't speak for the smaller engines used outside North America, though.

they said mine did this because my tires were not stock and were bigger then recommended

0!! There are no horses in car. If one was pulling the car, then i'd say 1 horsepower

To fix a Mazda 3 ABS light 05 plate from staying lit you will need to see a dealer. They will need to use their computer to reset the code as long as the ABS light is faulty and not the actual ABS system.