Mercury Topaz

The 1993 Mercury Sable backup light relay switch can be found beneath the drivers side dashboard. The backup light relay switch will be above the accelerator pedal.

Take out the olod radiator, put in the new one and done

There is a cold start valve in the fuel system that could be bad. Or the temp. sending unit could be bad as well. Check your fuel filter first! where is the cold start valve,how does it work.

Since you failed to specify the engine all I can say is this: Carefully drain the coolant to the thermostat housing level so that none contaminates the ground. Remove all hoses and electrical connectors from the thermostat housing. Make sure you have the appropriate gaskets and seals for your engine by looking through the hose openings. If everything is correct, unbolt the housing and remove all gasket material from it without damaging the susurfaces. Reassemble being careful to center the thermostat in its correct position. If it moves during re assembly use a hook to hold it in place during the last bit of tightening. Fill with new coolant and "burp" the system.

I just did this on my 93 and 91 to swap them over because the one set of springs was shot. It got kinda brutal though.. but in a backyard it might. Lift the front end of the car off the ground. both sides need to be off the ground to make it easier. Take the wheel off the side you want to remove. undo the 10mm head bolt that holds the brake line on. turn the line so it comes off the strut. Then undo the 18mm head bolt that goes through the knuckle and strut. next is the brutal part. take a fairly big hammer and hit down on the knuckle till you can pull the strut out at the bottom. if you can push down on the wheel studs with your foot at the same time it helps. Once it is out then you have to remove the two or 3 or 4 nuts at the top of the strut. there may be other components attached to the top under the hood. once it is free simply pull it out. Be very careful not to hit the brake rotor while swinging the hammer!!! Installation is the reverse. Make sure the 18mm bolt is good and tight. if you did hit the rotor clean up the spot with a file....

To replace the rear brakes on a 1993 Mercury Topaz, start by safely lifting the vehicle and removing the rear wheels. Next, remove the brake caliper by unbolting it from the bracket, then slide it off the brake rotor. Replace the brake pads, ensuring to compress the caliper piston if you're installing thicker pads, then reassemble the caliper and reinstall the wheels. Finally, pump the brake pedal to ensure proper brake function before driving.

To install a water pump on a 4.5 Mercury marine engine, first, disconnect the battery and drain the cooling system. Remove the lower unit by unscrewing the necessary bolts and detaching any linkages. Install the new water pump impeller and housing, ensuring proper alignment and sealing. Reassemble the lower unit, refill the cooling system, and reconnect the battery before testing the pump's operation.

The 1997 24 ft Triple E Topaz fifth wheel typically features a gross vehicle weight rating (GVWR) of around 7,000 to 8,000 pounds and a dry weight of approximately 4,500 to 5,500 pounds. It often includes amenities such as a kitchen with a refrigerator, stove, and sink, a bathroom with a shower and toilet, and sleeping accommodations for up to six people. The interior layout may vary, but it generally offers a comfortable living space with dinette seating and a sofa. Additional features may include air conditioning, heating, and storage compartments for convenience.

In a 1991 Mercury Topaz, the starter relay is typically located in the engine compartment, near the battery. It is usually mounted on the driver's side fender well or close to the fuse box. You may need to consult the owner’s manual or a repair guide for the exact location and wiring details.

On a 1993 Mercury Topaz, the transmission fluid fill is typically located on the transmission itself, near the dipstick tube. You can find it on the passenger side of the engine bay, close to the firewall. To fill the transmission fluid, you may need to use a funnel and pour through the dipstick tube, ensuring the vehicle is level and running for accurate fluid level checks. Always refer to the owner's manual for specific details and fluid specifications.