0
Mitsubishi Galant
The Galant is a car built by Japanese automaker Mitsubishi. The car was launched in December 1969 as “Colt Galant.” It is available as a two- and four-door sedan and features a choice of 1.3 or 1.5 L four-cylinder engines.
1,291 Questions
Where can you find the Mitsubishi stereo unlock code?
Dr. DB
If you do put in wrong number three times the system locks. You must leave your key in the accessory position for 30 minutes. This will reset the system security and you have three more attempts. Also your car will run poorly if at all until the code is entered correctly.
zenone
How do you replace the tag-illuminating light bulb on a 2003 Mitsubishi Galant?
You can access the bulb for the license plate illuminator by popping the trunk and looking directly behind the plate holder on the trunk-lid itself. There should be a swist type quick release plug that holds the bulb in place. (similar to the third tail-light on models without the spoiler)
How do you manually close a sunroof?
There should be like a round circular plastic piece arond the sunroof. You need to peel that plastic piece off and you will need to use allen keys to manually close it.
Do 20 inch rims fit well on a 2000 galant?
WOW! 20"s on a car stock with 15"s and you ask does it fit "well". About the same as an elephant having sex with an ant....LOL. Yeah, you can force it but, the rim offset places so much strain on your suspension that your cost in new struts, tie rod ends, stabilizer bar links, and new tires (from the car not being in alignment) will cause you to immediately notice that "phat rims" ain't worth the cost of upkeep. Because of the low center of gravity a Galant has, a 17" is about the largest you would want to use without much out of pocket expense. An 18" can be installed without rubbing the wheel wells or a rough ride but the tire is such a low profile, please don't hit anything in the road greater than an anthill. So, if this is the case with an 18"....imagine what the damage to a 20" would be if you hit an unforseen pothole.
Mitsubishi magna advance 99 rego plate lights not working any suggestion why?
If the dash lights aren't working also it's the fuse. It's located in the fuse box under the bonnet and should be 15 amps. If it's just the rego plate light it may be the bulb or you may have caught the wiring loading the boot.
Where is the horn located under the hood on a 2000 Mitsubishi galant?
It is located behind the radiatior low on the drivers side of the car. Don't confuse it with the "alarm" horn above the front right tire. My horn just died, and I am in the process of replacing it.
What oil to used for a Mitsubishi Galant?
Engine Oil - use with API certification
Transmission Oil - Used OEM Mitsubishi Transmission Oil Only.
On the 2.4L 4 Cyl. engine, the stock gap should be 0.044
this is a confusing question..but i think your best bet would be to consult your owners/chiltons manual. they lay it all out there for ya buddy. good luck!
How do you replace window regulator in a 2001 Mitsubishi galant?
I replaced the window regulator in my 03 drivers side front and I found it to be quite easy.Before you start,its best to duct tape the window in the up position to keep it out of your way and to reduce the risk of glass breakage.First you need to remove the inside door panel.The screws are located around the panel and have little plastic plugs covering them up.They just ''pop'' open to allow access to the screws.There are two more screws located behind the door lever and one in the bottom of the door grab handle.You might have to clean dirt out of the grab handle to see it but its there.Once the screws are removed,you have to grab the panel and pull it off of the inside door skin.The panel has plastic tabs holding it in place and you need to pop them off.Dont worry,they pop back in just fine.Once you get the panel to move freely,you need to pull up on it to get the top out of the window sill.After its out of the sill,you need to unplug the power wire plug connected to the switch panel.Once you get the panel off you will see a clear plastic sheet covering the door.This is just sound proofing and once you pull the screws off for the metal door handle,this needs to be cut off with a razor blade.Be careful not to cut it up,your going to need to use it again.After all this,you should be able to see the regulator through a couple of access holes.The regulator has four screws holding it in place.Two on the top,and two on the bottom.The top two screws are located through a access hole on the top of the door skin.A flashlight will help to find these.Unscrew these two screws and then unscrew the bottom screws located on the bottom of the door skin.You should see the bottom screws on the outside of the panel,so there is no need to look through any holes to find these.Once the screws are removed the rest of the window regulator should just slide right out the ''big'' access hole.These regulators are cheaply made and when they go,they break apart,so dig around on the botoom of the inside door skin to pick up whats let of the original.[springs,cable,etc] Now all you need to do is reverse the process.The new one should go in the same way the old one came out.You might need to move the new regulator so it lines up in the top two screw holes by plugging in the power cord and rolling to window up.After the new regulator is in just put everything back the way you took it off.I used sillicone to seal the clear plastic soundproofing back on.
After seeing the length of my post it looks like this would be a tough job but it really isn't.Im not a mechanic but if you can change plugs and wires on your car,this should be pretty easy for you.I hope someone finds this helpful.
What would cause a 1999 Galant to not idle?
timing off,base timing not set,dist. not set in right position, timing belt about to break, low fuel pressure,burnt valves,leaking head gasket.need more symptoms.
How do you install the timing belt for a 1993 Suzuki Sidekick?
http://www.kick-fix.com/
see timing belt section. for both motors , 8v and 16v.
It is a pretty big job and if you want to tackle it I suggest you get a manual from a parts store for about $18 and it will have pictures and everything. You also will have it for the next repair. Good luck.
What could be the problem with the steering locking up on a Mitsubishi Galant?
Depending on the model and year, there is a problem with steering box. Google "Galant recall" you should find the recall date for this problem. Once you find it, call a the dealer who last worked on your car and ask if you can get a copy of all "recall work" done on your car. If the steering box was not replaced, call the dealer and demand that the box be replaced per the recall. If this fails, call the 800 number listed when you Googled for the information.
Sam
Where is the thermostat on 2003 Mitsubishi outlander?
The thermostat is at the top radiator hose. It is in the inlet where the top hose connects to the engine.
How do you change timing belt on Mitsubishi Galant sigma 1200?
Follow these steps to replace the Timing Belt on your Mitsubishi Galant:
1) Disconnect the battery ground cable using a wrench. Remove the splash guards and loosen the accessory drive belt tensioners, then lift the accessory drive belts off the pulleys.
2) Remove the top engine mount and its bracket, the alternator and the power steering pump and leave the power steering fluid lines attached to the pump, and just lay the pump out of the way.
3) Remove the air conditioning compressor and the crankshaft pulley bolt, then pull the pulley off the snout of the crankshaft. Remove the belt guide plate, the timing belt cover cap and the timing belt covers.
4) Turn the crankshaft until the crankshaft timing marks line up. If the camshaft timing marks do not line up, turn the crankshaft one more time, then all the marks should line up.
5) Now, loosen the tensioner bolt and push the tensioner away from the belt. Tighten the bolt enough to hold the tensioner out of the way. Lift the timing belt off the sprockets and pulleys. Check that the timing marks are still lined up.
6) Install the timing belt working in a counterclockwise rotation, starting with the crankshaft sprocket. While keeping tension on the belt, route it over the right camshaft sprocket. Hold the tension, then route the belt under the water pump pulley, over the left camshaft sprocket, then behind the tensioner pulley.
7) Loosen the tensioner bolt, allowing the tensioner to put tension on the belt. Turn the crankshaft clockwise two turns until all three timing marks are lined up again. Tighten the tensioner bolt and the crankshaft pulley and install the rest of the parts in reverse order of removal.
How do you add transmission fluid to a automantic transmission on a Mitsubishi galant es 1999?
The fluid goes through the dipstick tube. The dipstick/dipstick tube is under the big air intake hose, near the battery. It's not very well marked.
What does an angle crank sensor do in a Mitsubishi Galant?
Crank angle sensor reads rpm and sends the signal to the ECU (computer) to aid in the calculation of engine rpm, ignition timing, fuel injection and crankshaft position.
Is the 02 Mitsubishi Galant cylinder head is that an interferance head?
Honda Man The 2.4 Mitsubishi engine is an inteference engine. When a timing belt breaks on this engine valve damage can occur.
What does P0300 mean on a 2000 Mitsubishi Galant?
Trouble code P0300 means: Random/multiple cylinder misfire detected
How do you replace the water pump on a 1997 Mitsubishi Galant?
To replace the water pump you are going to have to go down past the timing belt. if you dont feel comfortable replacing the timing belt then you would be better off leting a pro handle it. the reason i say that is cause if the timing belt is reinstalled incorrectly it could cause major engine damage (bend the valves)
