0
Nissan Quest
The Nissan Quest is a minivan produced by Nissan since 1993. It was a successor to the Nissan Axxess and Nissan Vanette. The fourth-generation Nissan Quest features a continuously variable transmission and a 3.5L VQ series engine with 260hp.
792 Questions
Where is the fuse for the passenger window on Quest 2000?
200 Nissan Quest Windows FUSE location. Open up the hood, standing in front of the vehicle, Open the top of the fuse box that is in the bottom left side of the battery. Inside the top pasltic box, there is a diagram which fuse is the one for the Windows-There is an arrow pointing to the front of the vehicle to guide you when holdgin the plastic cover.
How do you open a jammed drain plug on a 1995 Nissan Quest to do antifreeze flushing?
there are other ways of flushing the antifreeze out besides the drain plug if the drain plug is jammed. for instance, loosen the clamp on the hose at the bottom of the radiator and pull the hose off. make sure to have a bucket or something large enough to catch all the fluid but small enough to fit under your vehicle. and watch out! it comes out fast!
Where can you find the make and model number of the stereo in a 1999 Nissan Quest GLE?
The owners manual will list the standard model number that comes with the car. You can gently remove the stereo and look on the back. The model number will be on there. The make should be on the front.
How to replace high mount light bulb in Nissan Sentra?
If this was in the service manual, I didn't see it. Get in the back seat of the car. The housing for your brake light is the gray plastic thing. The "shelf" is the gray fuzzy flat thing it's sitting on. There are 4 hooks holding the assembly onto the shelf-- 3 on the shiny side (facing outward), 1 on the dull side (facing you). See the link below for two pictures of the hooks on the housing so you know what you're working with. Push firmlyagainst the dull side, pushing it toward the window. While you're doing this, either wiggle it or try to lift the dull side to unfasten the single hook on that side. Once you've succeeded there will be a quarter-inch gap between the shelf and the housing. Pull gently on the housing to release the remaining 3. Don't pull too hard-- there isn't much slack in the wiring so you could rip it straight out if you're not careful. Also be mindful of your rear window; hitting it with the brake light assembly could damage your defroster. Also, if you shatter the bulb it's a pain to clean up and remove from the wiring harness.
Once it's off completely, you'll see the wiring go into the housing through a little black thing. That's the wiring harness. Turn it a quarter-turn and pull it out of the housing. Don't force it-- try turning it the other way if it won't budge. Be gentle with it to avoid breaking the bulb. With the wiring harness extracted, remove the light bulb like you would a tooth-- wiggling while firmly pulling. It does not screw in. Stick the new bulb in and work your way backwards through the steps above.
When do you replace a timing chain on 06 Nissan Quest?
To my knowledge the Nissan Quest does not use a timing chain, it uses a timing belt, with a replacement interval of 105,000 miles.
How do you change the ignition switch on a 93 Nissan quest?
Begin by removing the retaining ring at the top of your 1993 Nissan Quest ignition switch. Slide the ignition barrel out. Remove the wiring harness from the end of the ignition barrel. Reverse the process to install your new ignition switch.
Changed the timing chain and guides on 1995 Nissan now valves making noise What is wrong?
I had the same thing happen to me when i replaced my chain. It turned out to be that the oil pump and the spindle must be alligned 100% with the punchmarks or you will not have enough oil pressure, hense the tensioner(oil pressurized) wont tension
Where is the oil sending unit on a 2000 Nissan Quest and how do you change it?
On my 1999 Nissan Quest, it is located under the car (front passenger side), just above where the oil filter screws in. It has an electrical connector on one end, and it screws into the car on the other end. After removing the electrical connector, just unscrew the oil sending unit. I heard there is a special 1-1/16" socket that makes the job easier. I am not sure as I have not tried to replace it. Based on where it is located, I suspect some oil to leak out when replacing it, so you may want to have oil handy.
Does Nissan Quest YEAR 2000 need a timing belt change?
According to the Gates website , the 3.3 liter V6 engine in a 2000 Nissan
Quest has a timing BELT that is changed at 105,000 miles ( it is also an
interference engine )
How do you tell if a cv boot is bad on 2005 Nissan quest?
Inspect the boot and look for a tear or hole. If you see any the boot is bad and needs replacing. The joint itself will pop, and make noises if it is defective.
Inspect the boot and look for a tear or hole. If you see any the boot is bad and needs replacing. The joint itself will pop, and make noises if it is defective.
if it fits, make sure no air with dirt can by-pass filtration...a teaspoon of dirt down the intake is like 100,000 miles of wear on the rings..have fun: also everyone should have a manual for their vehicle, and the local library should have a SHOP manual available in the reference section--make copies of the right info and read up..you'll be a pro in no time ...good luck:)
How do you change the third brake light bulb in a 2006 Nissan?
2 nuts in the trunk, unscrew those, then the light housing will pop off
pry the plastic off and replace bulb.
Where is the tire jack for the 2006 Nissan quest located?
I have a 2000 quest, and the jack is under the 3rd row seat in a pouch anging, don't know if is the same in a 2006.
Hope this helps.
How much will it cost to replace the oil pan on 1997 Nissan quest?
Buy it at a salvage yard and it will cost about $10.00. Another few dollars for the gasket/seal, it's cheap. Check the torque specs and don't over tighten. It there are no junk yards in your area, just go on line. You can search across the country and have the part shipped.
Where is the radiator drain plug for a 2004 Quest?
The drain plug for the coolant on a 2004 Nissan Quest is on the lower corner of the radiator on the inside. In other words, on the side of the radiator that faces the engine.Ê
How can you test or erase the trouble codes manually on a 2001 Nissan Quest?
Borrow, rent or buy a good quality OBD2 code scanner. The good ones let you clear the codes. Any codes that WON'T clear are usually caused by a failed component that needs to be replaced.
How do you replace the front blower motor on 2007 Nissan Quest?
These instructions are for a 2007 Quest with Nav and Dual Climate Control. It appears from the parts book that this is applicable to all models, but I can't guarantee that. I have pictures of this process from start to finish if needed. This is a little tricky and took me a few hours to figure out, but can be done in a couple hours easily.
1. Remove cover behind Nav system. This is done by using a plastic or other soft tool to pry at the front, closest to the windshield, and working around. It should pop up easily.
2. Remove the tray that holds the GPS antenna unit and small speakers. 4 phillips head screws. Remove the 2 screws holding the GPS unit.
3. Lift up this tray removing the GPS antenna, and unplug the two speakers.
4. Remove the Nav screen and computer by taking out the 4 phillips head screws on the brackets behind the screen. Then pull up and the unit should pop up. Unplug the computer and the Nav screen from the harness.
5. Remove the two black 8mm hex head screws holding the defrost ductwork. Now here's a tricky part: you have to remove this duct which is a real PAIN. pull up hard on the front, closest to the windshield, until it pops past the connection to the windshield defrost outlet. You have to deflect it a lot, but it will come.
6. Now looking down you will see the top of the blower motor and double squirrel cage fan unit. There is a large two-wire harness that you will unplug.
7. Now remove the four silver 5.5mm hex head screws (or 7/32") that secure the top housing of the blower motor unit. It helps to have a 1/4" drive with a Universal Joint to get to the front two screws.
8. Pull hard upwards on this top housing to break the sticky seal and this unit will come out along with the motor. You may have to work it slightly side-to-side to get it to come out of the ductwork. Also, you have to roll it and force it slightly to come out of the hole in the dash left by the Nav removal. It likes to get hung up on the defrost outlet duct opening, but it will come out.
Now you can test the unit or replace it. Putting the motor assembly back in requires a little forcing to get it past the defrost duct opening.
The real bugger of putting this all back together is getting the defrost duct back in place. There is a wire harness jammed in the same area, and the duct will really want to hang up on the silver 5.5mm screws that hold the motor unit in on the rear, away from the windshield. I found that using a long, plastic pry tool will help pop it over these. Also, the duct wants to tuck slightly to the driver's side, not centered in the hole. You'll just have to work at this to really force it in, but eventually it will pop into place. Then adjust it so it lines up with the front defrost outlet duct and you're in business.
Reinstall the Nav system (don't forget to plug everything in). The screen harness runs up through the mount bracket on the driver's side.
Reinstall the tray and GPS antenna.
Snap the dash cover back into place. Viola.
Quest tps sensor p0120 problem does'n shift?
if someone has the same problem after changing the tps check the signal wire on the sensor make sure is not grounded is the middle white wire on the top connector mine was a 1997 quest and i did have the trouble codes p0120 p0325 p1705 and the wire was grounding in the engine harness you can bypass the wire the connector on the front of engine(belt side) red wire save a lot of money
Changing cabin filter for Nissan maxima 2002?
How to clean or replace the in-cabin microfilter The in cabin microfilter should be cleaned/replaced once a year or every 15,000 miles. The filter came standard on '02-'03 Maxima's and was an option on '00-'01's. Even if your Max doesn't have an in cabin filter, you can order one from Courtesy Nissan or your local dealer. All 5th gen's come with the cabin filter housing and plumbing. However, the replacement filters are made out of a different material then the original filter and must be replaced when dirty instead of cleaned. # Determine if you Maxima is equipped with the in-cabin filter. Check for this label in your glove box:
# Remove screws around glove box
# Pull glove box toward you. Retaining clips will release. It takes quite a bit of pressure to remove the retaining clips so don't be alarmed.
# This picture shows the plugs disconnected, however, DO NOT DISCONNECT these plugs. Instead, remove the two clips (in the lower left hand side of the picture) that attach the yellow air bag plug to glove box housing with needle nose pliers. This will allow the glove box to fall down far enough to allow access to the filter.
#
Did this help you out? Feel free to throw us a bone to help keep housecor's how-to's hosted!
Remove glove box bulb housing by twisting counter clockwise.
# The filter housing is now visible - It is the white rectangle in the center of the picture. Remove the black clip and the bottom of the filter housing circled in red with pliers:
# Slide the filter out of the housing. My filter was pretty nasty looking for a 1yr. old car. A ton of leaves and bugs fell out when I removed it.
# Dip and stir the filter in warm soapy water if it is the original or replace if necessary.
# Rinse filter
# Allow to air dry
# Reinstall filter and reassemble glove box.
