Plymouth Colt

To install the third-row seat in a 1995 Mitsubishi Expo, first, ensure you have the necessary mounting brackets and hardware. Position the seat in the designated area and align the brackets with the pre-drilled holes in the vehicle's floor. Secure the seat by tightening the bolts or screws to ensure it is firmly in place. Finally, check the seat for stability and ensure it functions correctly before use.

To recharge the air conditioner on a 1989 Plymouth Colt, locate the low-pressure service port, which is typically found on the larger diameter aluminum line connecting the evaporator to the compressor. The high-pressure service port is on the smaller diameter line. Use a refrigerant recharge kit to connect to the low port, following the manufacturer's instructions for adding refrigerant. Always wear safety goggles and gloves, and ensure the engine is running with the A/C on during the recharging process.

In a 1989 Plymouth Colt, the horn is typically located in the front of the vehicle, often mounted near the radiator support or behind the front grille. You can usually access it from underneath the front of the car or by removing the grille. If you're having trouble locating it, consulting the vehicle's service manual can provide specific details.

The relay switch on a 1994 Plymouth Colt is typically located in the engine compartment, near the battery or the fuse box. It may also be found under the dashboard, depending on the specific system it controls. For accurate identification, it's best to consult the vehicle's service manual or wiring diagram.

The relay layout for a 1993 Plymouth Colt typically includes various relays for systems such as the fuel pump, headlights, and ignition. These relays are usually located in the engine compartment fuse box and sometimes within the cabin fuse panel. To find the specific relay configuration, it's best to consult the vehicle's service manual or a fuse box diagram, which outlines the exact placement and function of each relay.

If a '92 Colt Vista won't start after installing a new distributor, it could be due to incorrect timing, improper installation, or a faulty distributor. It's essential to ensure that the rotor is aligned correctly with the engine's timing mark. Additionally, check for any loose connections or damaged wires, and verify that the ignition coil and spark plugs are functioning properly. Lastly, ensure that the new distributor is compatible with the vehicle's electrical system.

To replace the clutch on a 1991 Plymouth Colt, start by disconnecting the battery and removing the transmission from the vehicle. This involves draining the transmission fluid, detaching the drive axles, and unbolting the transmission mounts. Once the transmission is out, remove the old clutch assembly, including the pressure plate and flywheel, and install the new clutch components, ensuring proper alignment. Finally, reassemble the transmission and reconnect all components before testing the new clutch.

To change the fuel pump on a 1994 Plymouth Colt, first disconnect the negative battery terminal to ensure safety. Remove the fuel tank by detaching the straps and any necessary components like the filler neck and fuel lines. Once the tank is lowered, access the fuel pump assembly, usually located on top of the tank, and remove it by unscrewing the retaining ring. Replace the old pump with the new one, reassemble everything in reverse order, and reconnect the battery.

On a 1994 Colt Vista, the horn relay is typically located in the engine compartment, near the fuse box. It is often mounted on the inner fender or near the battery. To access it, you may need to remove the cover of the fuse box to see the relay labeled for the horn. Always refer to the vehicle's service manual for precise locations and diagrams.

There isn't one.

http://www.ecmtogo.com/ Call 1-888-ECM-TOGO

Check the ignition coil or the "pick up" located inside the distributor

The fuel pump is in the top of the gas tank unfortunatly.

It's .39 to .43

I have had the same problem. What i did to fix it is to remove the two bolts from the center and ensure to remove all old gasket material. on the left side(passenger side) there is a half circle rubber that tends to dry up. i replaced the gasket and applied a GENEROUS coating of heat resistant silicone to all gasket surfaces including the rubber and ensure that the rubber bolt seals get a good coat as well. WAIT AT LEAST an HOUR before starting to allow the silicone to set up some.

use a small screwdriver to pry out the wire retaining clip located half way down on the plug.

If equiped with a blue plastic clip in the connector:

Pull or Pry the blue clip halfway out, using a small screwdriver or plyers. Push the tang on the side and completely remove the blue clip. Now with the blue clip removed squeeze the tang and pull the connector off.

Its on the passenger side right behind the front bumper.

5w30 or 10w30

On a 1991 Plymouth Colt, the fuel pump relay is typically located in the engine compartment, within the fuse and relay box. This box is usually found near the battery or on the driver's side of the engine bay. To access the relay, you may need to remove the cover of the fuse box and refer to the diagram on the inside of the cover for the exact location. Always ensure the vehicle is turned off before attempting to locate or replace the relay.

The starter on the 1993 Plymouth Colt is mounted on the back side of the engine (by the firewall), and below the intake manifold.

The 1992 Plymouth Cold ignition switch is held in place by a retaining ring. Remove the retaining ring at the top of the ignition switch. Pull the ignition switch out. Remove the wiring harness from the ignition switch. Reverse the process to install the new ignition switch.