answersLogoWhite

0

Toyota Matrix

Also known as the Toyota Corolla Matrix in some markets, the Toyota Matrix is a 5-door compact hatchback produced by Toyota in Canada since 2002. This compact car is sold in the US, Mexico and Canada.

705 Questions

How do I replace the serpentine belt on a 2004 Matrix?

First you need a breaker bar and 19mm socket to fit the "tension bolt". Turn tension bolt clockwise to release tension in order to remove the serpentine belt.

What is the cam type of the 2005 Toyota Matrix?

The 2005 Toyota Matrix has double overhead cam (DOHC).

How do you check and change a heater matrix on a Daewoo Matiz?

Matrix!?What is a heater "Matrix"? do you mean an element? i have never seen an electic elementy in a automotive interior heater, but i will admit that i don't know that they don't exist---but have never heared of a part named a "Matrix"...i think you may find a small radiator like vessel that takes coolant from the engines cooling system via a black rubber pipe (probably about 1 & 1/4 inch's diameter) through a valve, that is connected and controlled by the heater temperature dial/slide switch, that varies the volume of heated engine coolant that can circulate through the small radiatior like vessel that is in the interior ventilation air box cavity/enclosure. AnswerHeater matrix / heater core / heater rad they're all the same thing, the small impossible to get to approx 8" square little mini radiator that is nicely installed at the very back of the dashboard always. To check it, I suppose you will be looking for signs like a quick burst of hot when you select hot but then it quickly fades to cold again, that could well be a sign of a blocked heater rad. Wet carpets in the footwells could mean a leaking heater rad. Steamy windows that just cant be demisted - now that's a definite sign of a leaking heater rad and also the smell of coolant inside the car. The only check you might do on it is to check for it being blocked I suppose with a garden hose, you would need to take the hoses of the inlet/outlet ports in the engine bay and stick the garden hose to one of the ports, if the water shoots back out at you through the same hole then the rad is blocked I would say. Removing the heater rad now that's a task. My friend and I did one in 4 hrs flat last Saturday and I still cant believe we (he) managed it that fast. He removed the centre console and then the black trim around the radio and instrument cluster. Then he disconnected the instrument cluster and removed it too, the radio also landed in the back seat along with the previously mentioned stuff. Next came the steering wheel and what to do about the airbag which was worrying us. He removed the glovebox and up above it is a yellow connector which he reckoned was the wire for the airbags, then he unbolted the passenger side airbag unit from the 'tie bar' leaving the passenger airbag mounted in the dashboard plastic. In the end we couldn't get the wheel off without a puller which we didnt have so the wheel stayed. This obviously makes removing the one piece dashboard impossible so having removed all the dashboard screws and bolts we just did our best to get in under it and get the job done. Next the centre steel unit which holds everything together in the mid section of the dash was unbolted (8 bolts). Pulling this now only forward enough to work behind at the final hurdle was possible. The big black plastic box unit (heater module) which can clearly be seen from the minute you start this job can now be unbolted from the bulkhead. When you've done that you need to split it down the middle by undoing the 8 or so screws all round it - its a bit like cracking a big Easter egg open down the seam. That done, split the box open, whip out the heater rad/matrix/core, lash in the replacement and put the box back together minding how the flaps should all be located properly as you do it. Now its just a case of putting it all back the way it was. The way we did it was definitely not as they recommend in the manual and I cant claim to have treated the airbag situation as we should have but cars are cars and they gotta be fixed and we don't all have the funds to be marching off down to a main dealer every time theres a fault. We got away without removing the wheel and the bags and the dash so maybe you can too. We were working on a M100 '00 Matiz. Best of luck to anyone who does it, just get your head together and tear into it, don't be doing the stopping and staring thing I am prone to, that's exactly the reason I enlisted my pal who doesnt hang about on a job.

Edit Raymond Snijkers:

I am currently changing (or trying to change) the heater matrix on a 2000 Matiz. I'd like to add to the above that there is no need to split the black box. You can simply slide the matrix out of the back of the box. There are two plastic 'hooks' at the back that hold it in place.

For me the biggest challenge is loosening the two radiator hoses from the matrix. These can only be reached via the engine compartment. But then the engine is in the way. Does anyone have an idea how to solve that?

Grant revan - Edit

Hi- I have just removed the entire dashboard to get at the matrix. You don't need a puller for the steering wheel - just bang the wheel a few times with a rubber mallet and then give a big pull - it will come off - honest. You can then remove the dashboard and the metal frame in front of the the heater unit and if you undo the 4 bolts securing it (the heater unit)to the bulk head it just lifts out leaving the matrix sticking out in mid air. You need a hose clip removal tool (flexible) to undo the hose clips in the engine bay - they are murder to get at with a pair of pliers - I have tried. You can buy them on eBay for about £20. NB you need the correct size torx bit to undo the airbags on both sides and you need the anti-tamper version which is quite rare. You do not need to remove the control stalks by the way, just the steering wheel. The dash will just fit over the stalks. Make sure you have the torx bit (its a 40 or a 45 I think) and the hose clamp tool before you try this job or you will not get it done in one go.

Brake caliper bolt Toyota matrix size?

m8-1.0x 20mm I just replaced mine, it was the top bolt

What is the maximum towing capacity of the 2009 Toyota Matrix?

The maximum tosing capacity of the 2009 Toyota Matrix is 1500 lbs..

What is the front leg room in the 2004 Toyota Matrix?

The 2004 Toyota Matrix has 41.8 in. of front leg room.

What is the maximum towing capacity of the 2012 Toyota Matrix?

The maximum tosing capacity of the 2012 Toyota Matrix is 1500 lbs..

How do you replace a serpentine belt on a 2003 olds v6 alero?

Confirm that a routing diagram exists near water pump or RH strut tower or draw one.

Use a 3/8" ratchet or 13mm open-end wrench to releive belt tension and remove the belt.

Route the new belt correctly around all pulleys except water pump or Alternator (your choice.)

While holding the tensioner in the slack position, put the belt arount the last pulley.

Confirm routing and seating of belt.

Start engine.

Reconfirm routing and seating of belt.

Where is the thermostat located on 2004 Toyota matrix?

The thermostat in a 1.8L Matrix or Vibe is behind the Alternator. The alternator must be removed to see the Thermostat housing. The T'sat housing is removed by removing the two bolts. Be sure to note how the old t'stat in oriented so the new one can be placed in the same way.

How does matrix get to its characteristic position?

By far the most abundant extracellular material is the extracellular matrix. Most body cells are in contact with a jelly like substance composed of proteins and polysaccharides. These molecules are secreted by the cells and self assemble into an organized mesh in the extracellular space, where they serve as a universal "cell glue" that helps hold the body cells together.

What is the base engine size of the 2006 Toyota Matrix?

The 2006 Toyota Matrix has a 1.8 L base engine size.

Your 2003 Toyota matrix runs great but gas mileage is awful why?

Have a mechanic check the O2 sensors. If one is out then the computer will give the engine too much gas. I have also seen some sensors go completely out and the check engine light does not come on.

How do you replace the serpentine belt on 1996 f-150?

Most cars and trucks today have what is called a serpentine belt which runs most accessories.They are very dependable and usually easy to replace. To decide if your belt needs replacing, simply look at the grooved side of the belt to see if it is cracking badly. A couple of cracks every 3 inches is normal, but if you see cracks every 1-2 inches I would recommend that you replace it. On most cars and trucks the procedure is basically the same. First off, get the correct belt by bringing your cars VIN number to the parts store(located on your cars dashboard) the parts store may need it. If there are two choices, get them both so you can complete the repair. Once you have the correct belt, take a minute to review how the belt runs across the pulleys and also check to see if your car/ truck has a underhood diagram of belt routing in case you need it. In most cases you will need a socket wrench or breaker bar with either a 3/8" and /or 1/2" head on it and possibly a short extension. Some models may require a wrench of these similar sizes.Now that you are ready to go to work, you will need to find the spring loaded tensioner which is generally located near the top of the belt path; it usually has a shinny pulley on it. Look at the tensioner and insert the tool into it and apply opposing pressure to release the belt.Now, simply install the new belt making sure it fits into the grooves on all the pulleys. Start the car to check it and you are done and you saved yourelf some money!

How do you replace 2005 Hyundai accent headlight bulb?

Open the hood and look behind the headlight. You will see a rubber cover with a electrical plug and wires coming out of it. Remove the electrical plug by squeezing the sides while pulling. Then take the rubber cover of. The bulb will be held in place by a metal wire. The wire if connected to the body of the headlight at the top, and held in place by a hook on the bottom. Push down on the bottom of the metal wire and it will come off the hook, and the bulb will come out freely. Then put in new bulb and reassemble in the opposite way you dissembled it. Have fun.

Alarm fob not unlocking your car?

the flashing security light in the dash is not flashing and vehicle will not start

How do you reset Maintenance required light on 2005 matrix?

Make sure the Odometer is NOT in the trip mode.

Turn off the ignition, then press the trip button and hold it in. Turn on the ignition. The odometer will turn to all dashes and start to count down and turn to all zeros. When the Odometer returns release the trip button and you are done.

How do you replace the oxygen sensor on a 2003 Toyota Matrix?

Find very good instructions with photos at:

http://matrixowners.com/topic/72977-diy-how-to-change-an-oxygen-sensor-in-a-matrix/

I used them and they are easy to follow. Replacement time 15 minutes.

What size are the factory speakers in a 2005 Toyota Matrix 4 speaker system?

Try to use Toyota speaker adapter plugs so you don't need to cut wires and mess the electric system up. You can get them from Ebay or Amazon.