0
Toyota Tacoma
Named after Tacoma City, Washington, USA, the Tacoma is a pickup truck manufactured by Toyota Motor Corporation from 1995 to the present. This vehicle is available in 4-door crew cab and 2-door regular cab body styles.
3,052 Questions
What year did the Tacoma 4 cylinder become a 2.7 Liter?
1995, was introduced as a replacement for the Hilux.
What is the difference between 235 75 r16 to 265 75 r16 in tire size?
The 235 / 70 / R16 is ( 29 inches in diameter , and the section width is 9.3 inches )
The 265 / 75 / R16 is ( 31.6 inches in diameter , and the section width is 10.4 inches )
So , 2.6 inches taller and 1.1 inches wider for the larger size tire
When you accelerate your 99 Tacoma makes a rattling noise?
Check for a loose catalytic convertere heat shield
How do you adjust the valves on a 1994 Chevy 4.3 v8?
For someone with little mechanic knowledge: run the nuts till they all (ALMOST) touch, turn the motor about A quarter of A turn, run the ones that got loose, Do this about 5 or 6 times. Then start the motor and SLOWLY tighten them till they quiten down, ONE AT A TIME. STOP TURNING AS SOON AS THEY BECOME QUIET, Once they are all silent, Go over each one, Loosen it till it clicks, and retighten ONLY till it quitens again. When all are EVEN and barely tight, Turn each one between A quarter turn and A half. CLOSER TO A QUARTER.
What is the timing degrees for a 2002 Tacoma 6-cylinder?
The timing is controlled by the ECM. It is nonadjustable.
What is top dead center on a 1994 22re?
In the field of automotive repair, we always refer to top dead center as.
The #1 cylinder being at the TOP MOST POSITION during its compression stroke.
The 22RE is no exception.
How do you torque the camshaft?
If you do not have a manual for this vehicle, DO NOT PROCEDE! You have invaded the heart of the engine, and if you do not have a manual, you run the risk of doing damage to the engine if you put it back together wrong. YOU MUST GET THE CAMSHAFT ALIGNED WITH THE CRANKSHAFT IF THE ENGINE IS TO RUN CORRECTLY! Anytime you are reassembling a large component, with multiple screws or bolts, finger tighten all fastners until all fastners have been run down finger tight. Then, working across the component, tighten one fastner snug, then go to the diagonal fastner, and tighten it snug. FOLLOW TORQUE SPECIFICATIONS! If you are working without a torgue wrench, try to tighten all fastners as uniformly as possible. Torgue specifications are critical on many automotive parts, and it is worth buying or renting a torque wrench to get them right. Work all fastners down in steps, avoid tightening one faster all the way while others are loose or only finger tight. This can cause warpage of parts, and may prevent all fastners from being tightened properly.
How do you change the speed sensor in a 2000 Ford F-150?
There is more than one speed sensor. There is one in the top of the differential housing. If you have a 4R70W transmission, there is a speed sensor in the side of it, and if you have a 4R100 transmission there are two speed sensors in it. If you have 4 wheel ant-lock brakes, there is a speed sensor in each front wheel hub. So there could be as many as 5 speed sensors. Which speed sensor are we replacing?
Reset the check engine light on a 1995 Toyota Tacoma?
take postive side of battery off then put back on
How do you change a gas filter on a Toyota Tacoma?
Without know the year and engine size it is impossible to answer your question.
Do your lights stay on? On my 2005, the lights go automatically off when the ignition is shut off.
Where are the hidden vin numbers for a Toyota Tacoma?
location is under the frame, you need to check on your local DMV to see if they match with the visible numbers (dash and doors)
Where is reset button on 1998 Toyota Tacoma fuel pump?
there is no reset button there is a circuit opening relay under the dash you can check it with an oms meter
How do you adjust valves on 1986 ford bronco 2.9?
Valve Adjustment Procedure For
1986 Ford 177 CID (2.9L) V6 Engine
To adjust the hydraulic lifters on this engine, position the cam so the tappet being adjusted is in the base circle area. Loosen the adjusting screw until a distinct lash between the rocker arm tip and the valve tip is evident. Carefully turn the adjustment screw until the rocker tip just touches the valve tip. Turn the
adjusting screw in an additional 1.5 turns.
Which Hondas have auxiliary audio input jacks?
Most Honda Radios from 2007 and up come with the auxiliary input jack somewhere in the dash, vehicles from 2003 and up comes with the AUX button on the radio but no way to connect anything because there is no jack in dash
The good news is that almost all Honda radios from 1995 and up are capable of doing this, there are adapters made for Honda radios these plug into the back of the Radio using the external CD changer plug or the XM satellite connection.
in new vehicles you can use the rear DVD port to add auxiliary audio input
from any portable audio device ( This are not FM modulator or transmitters )
To find the correct adapter just do a search on any search engine for
Honda Auxiliary Input Converter
How do you change a 2005 Toyota Tacoma cabin filter?
I'm not sure where your filter is. But in both my 2003 4runner and 2008 Tundra it's located behind the lower glove box. It's the same procedure on both. Open the box remove the clip/rod on the right side of the box. Squeeze in on the sides of the box to bypass the stop tabs. Remove the glove box. Behind it you will find a long narrow trap door with clips on each end. Release them and pull out the cabin air filter.
That's it. Your may be different. I found instructions in the box with a new cabin filter that I bought at a local auto store. $28.
Where is the intake air temp sensor located on a 2008 Toyota tacome 4.0L?
On the intake just after the filter housing. Why are you concerned with this? The vehicle is still under warranty. Take it back to the dealer if you have a problem.
What could be the reason for oil blow back into your air filter box on your 2000 Toyota Tacoma?
start with chnging your PVC valve it should go into your valve cover or into your air tube that's the cheap way
Why does your 2009 Tacoma have a random rough idle when you come to a stop?
I have exactly the same problem with my 2007 Tacoma, 24K miles. I don't have any other issues and the truck drives fine. My guess is if that we took it to the dealer, 1) they wouldn't be able to reproduce the problem or 2) they will tell us it is normal.
Anyone else have this problem?
I have a 2011 Tacoma 4.0L with 11K miles on it with a similar problem. It idles randomly/rough and is a bit underpowered (especially with a trailer). This is a condition that 'happened' at once at about 8500 miles. The first dealer told me I had water in the gas. The second dealer said the same thing. But, after driving another 2000 miles with the condition, they took a closer look. I would agree, its slight and perhaps a dealer wouldn't notice, but this is my third 4.0L Tacoma so I am very familair with how they should run. I had a 2006 and a 2008 prior to the 2011. I would highly suggest taking it in. My truck is scheduled to be looked at by a Toyota Field Representative in late January 2011. I hope they can fix this soon as I like the truck, but this is certainly not correct. Don't take 'water in the gas' as an answer, but be polite. Feel free to contact me if a dealer wans cross references. I think there are several of these problems out there, but Toyota doesn't know about them as they are slight and dealers are chocking them up to them being slight or user problems as this problem doesn't exibit engine codes. BTW, I did have mine shut down on me twice while on the highway while passing vehicles up a hill at high speed. Dealer can't recreate as it happened out in Wyoming where the speed limit is higher than where my dealer is located. The dealer has opened a Toyota service ticket on my truck. I'd be curious to see if anyone has an answer. They checked the fuel mixture, the spark plugs and the gas tank... no answer yet. I hope the Toyota Field Rep can help.
1995 What does it mean when the brake and battery indicator dash lights come on at the same time?
I have a 1996 and have found the following:
My brake light came on because the emergency brake cable binds and does not go all the way back to it's normal resting position. Upon looking under the truck, the pivot arm assy, (connects the single cable from the front to the two cables that go the rear drum brakes) was getting corroded and binding up. Try making sure the arm is all the way in the relaxed (read not engaging the rear brakes). This takes pressure off the cable and makes the light go out. Also check the spring that is part of the pivot arm as it might be getting weak/worn out.
You may only have a bad battery. My battery light came on when my alternator was about to die. All the lights started doing funny things (flashing and glowing dimly) then the truck finally died. Everything was OK when alternator was replaced.
David
AnswerI had these symptoms two weeks ago and the alternator stopped working two days later.Well guys, I too had that happen several times on my 1982 Toyota Truck. When the alternator's brushes wear out, they will trigger the parking brake and charge lights to come on...same thing if the water pump/alternator belt breaks. Now, if the alternator is delivering some electricity, but not the full 14.8 volts, it may cause the charge light to glow dimly when the engine is running, or it may not. If you have the lights coming on, it would be wise to use a battery charger to charge the battery while it is disconnected for alternator repairs (Take the battery out of the truck before doing this).
