How do you tighten a power steering belt on a 1999 Toyota Tercel?
To tighten the power steering belt on a 1999 Toyota Tercel, first, locate the power steering pump and its mounting bolts. Loosen the adjustment bolt and the pivot bolt on the pump to allow for movement. Then, pull the pump towards the engine to increase tension on the belt until it has about a half-inch of play when pressed down in the middle. Finally, retighten the mounting bolts to secure the pump in place.
Where can you find an AM FM CD player for a 1986 Toyota Tercel?
If you want the original stereo this will be hard to find. If you want a new one, you can buy any aftermarket model that fits the opening (referred to as single and double DIN based on size of the stereo). Several online stereo dealers include all the mounting hardware and cable adapters at no charge (sorry I cant include names, it can be mistaken for an endorsement and the moderator will delete my post) just search for car stereos and you will find several online dealers available that can actually tell you what stereos will fit in your specific car.
On a side note, for not much more cost than a basic model, you can get a unit with built in bluetooth that will give you hands-free phone and access to your iPod/MP3 player music library in your vehicle.
How do you replace the fuel pump in a 1991 Toyota Tercel sedan automatic?
The fuel pump is located in the gas tank. Remove the rear seat bottom by lifting on the front edge of the seat. There is an access panel that removes with three screws. Once the panel is off, you will see the top of the fuel pump assembly. Disconnect the wire harness and remove the bolts that hold the pump in (about 10). Gently remove the fuel pump assembly, and gently install the new one. Reverse the directions for removing the pump to complete installation of the new one.
Where is the connection for the rear speakers in a 1990 Toyota Tercel?
last week i installed a new radio in my sister tercel , the car didnt had a radio at all , the rear speaker wire was missing in her car, i guess Toyota didnt intall the wire if u havnt buy the radio option.
solution: buy 4 wire, long enough to get from the radio to the trunk, next step, make your way to the trunk by removing the plastic trim along the door frame and then take the wires under the back seat and tadam the wires are in the trunk
There should still be rear speaker connections, I think you just failed to find them. My Tercel also lacked rear speakers but had the wires tied into the rest of the wiring harness with speaker attachment clips on them. You need to look where the jack is stored and somewhere (that escapes me right now) on the other side as well.
What is tire pressure for 95 tercel?
Check owner's manual or door jambs, or fuel filler door or glove box door for a label
Most I've observed is from 29-35PSI, you're better off on the high side as the lower the preassure, the less load your tire can handle.
How can you make the gauge cluster of a 1996 Toyota Paseo with a tach work on a 1997 Toyota Tercel?
i think it's a plug and play thing since the plugs ang wiring are nearly identical
sounds like it is a problem with the starter, which could also be caused by other problems. Have it properly diagnosed by a Ford Factory Trained Technician and any Ford Dealership.
first
make sure the battery is charged completely. My car does this when my battery is low. all the electronics may still work at that low charge but it is not enough for the starter to turn over the engine.
Where is the air filter in a 1996 Toyota Tercel?
Right side of engine in square type box that is made of plastic.There should be about 4 or 5 clips to disengage to remove the top cover.Toyo joe
How do you replace 1991 Toyota tercel right tail light?
open the trunk, and pull back the carpet and there will be 2 nuts holding the light in place. unscrew them and pull the light out.
What is the firing sequence for a 1997 Toyota Tercel?
How do you change a fuel pump on a 1997 Toyota tercel?
The fuel pump is located in the tank. You will need Pliers, a Phillips screw driver, a 14m and 13/16 wrench. Remove the back seat. Pry off access cover and you will see the top of the tank. Disconnect the 3 lines that go to the fuel pump. Remove 8 Phillips screws, and carefully pull out fuel pump assembly. Remove and replace strainer and pump. Reverse procedure for installation. NOTE: you will need silicone to reseal access cover. NOTE: Procedure was done on a 1995 Tercel, 1997 should be the same.
What is the firing order for a 1987 Toyota tercel?
haynes manual says 1-2-3-4 with carb, 1-3-4-2 with fuel inj.
What causes the AC on-off switch to blink on a 1995 Toyota Tercel?
The main reason for this is a sliping drivebelt, very common after you pressure wash the engine and the drivebelt gets wet; also Check the tension on the drivebelt. Another reason may be a defective expansion valve.
Where is the fuel pump at on a 1982 Toyota tercel?
if u r facing the engine. it's on your left side toward the back of your valve cover. can't miss it. or if u knw where your fuel filter is.. follow the fuel lines.
Biggest wheel size that can be put on a 1992 Toyota tercel?
im using 16s with 205/40r/16 tires, might be able to use 17s with 195s though im not sure
Ignition Switch
REMOVAL & INSTALLATION
Toyota Tercel 1984 - 1994 Repair Guide
REMOVAL & INSTALLATION
See Figure 1
CAUTION
On models equipped with a Supplemental Restraint System (SRS) or "air bag,'' work must NOT be started until at least 90 seconds have passed from the time that both the ignition switch is turned to the LOCK position and the negative cable is disconnected from the battery.
1. Disconnect the negative battery cable.
2. Remove the screws which secure the steering column upper and lower covers.
3. Turn the ignition key to the ACC position.
4. Push the lock cylinder stop in with a small punch or screwdriver.
Page 1 of 3 AutoZone.com | 1992 Toyota Tercel 1.5L FI SOHC 4cyl | Repair Guides | Chassis Electri ... 6/17/2009 http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?chapter ...
On some vehicles, it may be necessary to remove the steering wheel and combination switch first.
To install:
Fig. Fig. 1: Depressing the lock cylinder stop tab
5. Withdraw the lock cylinder from the housing while depressing the stop tab.
6. Remove the ignition switch retaining screws, then withdraw the switch from the lock housing.
7. Align the locking cam with the hole in the ignition switch, then insert the switch into the lock housing. 8. Secure the switch with its screws.
9. Make sure both the lock cylinder and the column lock are in the ACC position. Slide the cylinder into the lock housing until the stop tab engages the hole in the lock.
10. Install the steering column covers.
11. Engage the ignition switch connector.
12. Check the ignition switch operation in all positions.
----------------------------------------------------------------------------- ------------------------------------------------------------------------------ * Disconnect the battery * Remove the lock cylinder * MOST APPLICATIONS * Turn the switch to the accessory position * Insert a straightened paper clip into the hole; there is a small button you press with the paper clip end * The key should now move further counter clockwise, and the key and cylinder should come out * Remove the bezel that holds the switch * Unplug * Make sure your new switch matches * Reverse the procedure to reinstall, the key and cylinder go in by inserting the same way as they came out and turning back to the normal position.
What is the firing order on a 1996 Toyota Tercel?
firing order should be 1-3-4-2 or slim chance it could be 1-4-3-2 try them both