0
Brake Fluid and Lubrication
Cars, trucks, motorcycles and even bicycles use hydraulic braking. Brake fluid is used to transfer the force applied into hydraulic pressure. In contrast, lubricants enable parts to move opposite each other in a perpendicular manner.
1,926 Questions
What causes brake fluid to leak from the rear wheel area on a Jeep Liberty 3.7?
Failed caliper, wheel cylinder, hose, or line.
How do you bleed brakes on a 1995 gmc vandura 2500?
Are both resivoirs supposed to have brake fluid in them? Because the container where you refill brake fluid is as full as it is supposed to be. So are you supposed to open the cap of empty resivoir and pour directly in? My brake light came on a couple weeks ago and i also have a spongy brake pedal. Thank you, Darin
A guess would be a bad brake booster. Usually if the brake fluid leaks into the booster it rots out the diaphragm and causes it to leak. Could also be the vacumm hose to the booster. Without more information it's hard to tell.
How do you add brake fluid to a 1998 ford contour?
Remove the Master Cylinder Reservoir cap and fill with fresh brake fluid from an unopened can to the full mark. Be sure and look on the cap and use the correct fluid. Normally DOT3.
Why does an abs light come on?
The ABS (anti-lock brake system) light comes on because the computer has detected a problem and set a code. The code will stay in the computer even if the light goes out. You need to have the system Scanned for codes. Once the cause of the code has been repaired the light can be shut off by clearing the code.
Most auto repair shops will have Scanners and all the equipment to Diagnose and repair the problem. And, Most auto parts stores can plug in a diagnostic scanning device into your vehicle to read the trouble codes at no cost if you purchase the parts necessary to repair the vehicle from them. The trouble codes can tell you THE AREA where the problem is with your ABS system. So it's wise to have a Tech check that circuit to isolate what the problem actually is.
In order to reset this light you need to have access to a Scan tool that does more than just read the codes. Other diagnostic equipment may be needed as well.
You have a problem with the ABS. As long as the light is on the ABS is not working. The light will remain on until the problem is fixed.
AnswerThe ABS system has stored a fault code. You'll need to have someone scan the ABS computer to read the diagnostic code. Typically, ABS codes are not available to inexpensive conventional OBD scanners.ABS = Anti-Lock Brake System
If you have this light come on while not braking, it most likely means there is a problem with the electronic controls in your brakes. If it comes on while you are braking, it means the Anti-Lock has kicked in. It should only do that however, if you are braking really hard. Addendum: It is very important to have the above procedure done to diagnose the cause. It might be minor but it could be as important as a wheel bearing, and a cracked hub, which if damaged could cause the wheel to become loose and you could lose control. I've added this addendum because I was told by a mechanic not to worry about the ABS light, that it was a minor problem. Only to find out later that in many vehicles the ABS sensor is attached to the wheel hub and a malfunctioning bearing can cause the sensor to slip., causing it to turn on.
What mileage should brakes be changed if you own a 2004 impala with 47000 miles on it?
That depends entirely on driving conditions and the habits of the driver. It is not unreasonable for a 2004 Impala to need new brake pads at 47000 miles. Once the brake pads are worn to the point of needing replacment, you had best get the job done and avoid additional expense.
What type of brake fluid does a 1998 Chevy blazer take?
dot 3 i believe should say on cap or in owners manuel
What angle should a master cylinder be mounted?
it should be at 95.7 degrees to the left of the fan belt.
Where does brake fluid go on a 2002 Dodge Neon?
In the reservoir under the hood, driver side, near windshield with the yellow cap.
In the reservoir under the hood, driver side, near windshield with the yellow cap.
Can you put synthetic brake fluid on top of silicone brake fluid?
If the synthetic fluid is silicone based, yes. If it is a dot 3or 4 type, no.
Can you use Honda DOT 4 brake fluid in place of DOT 3 brake fluid for your Honda accord 2010?
Yes, you can use either DOT 3 or DOT 4 and they can be mixed. You cannot use DOT 5.
How much do nail technicians earn?
it depends on how often they open the storeand many peoples hand they do and what they do
Where on a 1994 Nissan Altima do you put brake fluid?
Under the hood on the driver's side is a large round vacuum booster. Attached to it is the master cylinder. Before you add any fluid you will need to check and see which fluid is required, Dot3 or Dot4. Add fluid to the fill line or 1/2 inch from the top. DO NOT mix fluids.
Where is the brake fluid filler located in a 1992 GMC Sierra C1500 with a 305 engine?
On top of the brake master cylinder
What does brake fluid leaking from right side rear wheel mean on a 95 grand cherakee Laredo 4x4?
Most likely causes are a rusted metal brake line, cut or hole in rubber brake hose or possibly you have a wheel cylinder leaking. No matter the cause its very important to get it fixed because its likely that at some point your brakes will go out completely.
Where do you add brake fluid to 2001 Toyota Camry?
You can add fluid in the reservoir on the top of the main brake cylinder. It's located on the firewall just in front of the driver's seat in the engine compartment.
Can you get drunk on brake fluid?
No, brake fluid does not contain alcohol. Drinking it can kill you however, as a patient in rehab nearly found out.
Can you mix synthetic brake fluid with normal brake fluid?
Yes. Normal brake fluid is actually synthetic
