0
Chevy Beretta
This category covers questions about the Chevrolet Beretta, a compact sedan manufactured by General Motors and sold through its Chevrolet division. The Beretta went into production in 1987 and was discontinued in 1996, succeeded by the Chevrolet Malibu.
665 Questions
How can you rewire a washer fluid motor to just a toggle switch on an 88' Chevy Beretta?
Yes! Find the wires going to the washer switch and just use a toggle switch in it's place. If you can't locate the wires, you can just run power straight to the motor from the toggle switch. I recommend you use a spring loaded on/off toggle switch, to make sure you don't accidentally leave it in the on position.
because there is a short circut occurring in the turn signal switch. This is not a minor problem, as it could lead to the car burning up, or the wiring harness being ruined. Take the care to an automotive electrical specialist immediately, and cough up what they will charge to fix it. No matter how much it is, it will be far less than what ignoring the problem will cost you.
How do you replace the clutch in a 1990 Beretta GTZ 5 speed?
very simple pull ur axles out 30 mm socke then loosesn ur mount to trans axle then take out all urboult wich ar 15 mm then give some pull the trans should give and just fall out
Where can one purchase a Chevy Beretta?
Chevrolet Berettas can be purchased at auction at large shows/sales such as those run by Manheim Auctions. In addition Beretta enthusiasts at website such as Beretta Net will often post sales/auction information.
How do you replace brake pads in 1995 Chevrolet beretta?
Put emergancy brake on, then jack up the front enfd remove tires, use a 3/8 Allen tool to remove the caliper mounting bolts. Then remove the brake caliper, and remove pads from caliper. Next push piston caliper into the caliper, reinstall the caliper. Re install the front wheels, lower the vehicle, pump the brakes until they are hard once again, and your ready to drive again.
How do you change the headlight switch on a 1994 Chevy beretta?
Remove the center screw below the headlight switch, and the center screw below the wiper switch. Grab hold of both switches and gently pull towards you. The plastic around the gauge cluster should unsnap from the dashboard. Unplug the headlight switch from the wire harness behind it, and remove the other 2 screws below it. Gently pull on the dimmer and outer rings. They should slide off. The switch will fall out at this point. Installation is the reverse of removal.
Where is a thermostat in a Chevy Beretta v6?
I'm looking where the therma stat is location in a 1996 Chevy bratta at
Where is the blower motor resistor on a 1993 Chevrolet Beretta?
It is in the air conditioner /heater case behind the glovebox.
Where is the heater core on a 1989 Chevrolet beretta and is it hard to replace?
Behind the Radio/ Heater Control, center console, mounted against the firewall.
And yes, it's extremely difficult to replace. It involves basically tearing the entire dash board apart.
Is their a color specific wiring diagram for a stock stereo in a 91 Chevrolet beretta?
Check out this page: http://www.beretta.net/how_to/b-tech/stereo_wire_colors.txt
Where is the fuel filter on a 1990 Chevy Beretta?
It is located in front of the gas tank on the passenger side. theres one in the tank to, its a pre pump filter
Other then finding a belt the right size, I don't see a problem.
How do you Reset check engine light on 1995 beretta?
Resetting a check engine light without making the necessary repairs will do NO good as it will come right back on. You will need a GM Tech1 (or compatible) scantool to retrieve and earse (reset) codes from either a 1994 or 1995 Beretta. This is because GM was in a transitional period between 1993-1996 to comply with the government mandated OBD-II system. The diagnostic components in those years are a combination of OBD-I and OBD-II parts, and cannot be scanned with a standard scantool.
Unfortunately, unless you know someone with such a scantool (GM Tech1, Actron CP9150, etc.), you will need to go to a GM dealer to have your codes reset.
Why does the transmission on a 95 beretta not shift right?
Check your trans fluid with the engine running, if it is full you need more diagnosis...
Where is the engine bay fuse box on a Saturn l200?
This can be found directly behind the battery. the fuse box will have a red power tap terminal on it's side. The cover is labeled FUSES on the top. The cover has tabs on the short ends and just lifts off, this is also where the Oil Change reset button is located, along with the power relays.
Depends on how long the car was running. Let the car run for an hour at idle and if it never comes on, I would check the fan. It should come on at sometime. Check the relay..............I just had this problem on my '89 Beretta. DoratheExplorer
Speedo doesnt work on 1995 beretta where is speed sensor?
there are 2 ,the ones on the front brakes if you have ABS and the one inside the transmission that usually gives the speedometer the drive indication.
How do you disable the daytime running lights on a 1995 Chevy beretta?
Yes that's true i finally figured a way to kill those anoying daytime running lights, without doing any of those tricks that are going around,. Since nobody has ever given me a good way to permanently kill them i had to get complete wiring diagrams for all te lights from ALLDATA. These diagrams are a lot more detailed than the ones you get from the manuals.
Ok, First you have to locate your DRL module, behind the radio. there will be a lot of wire coming out of it. But we are only going to be concerned with two.
NOTE: we will not be removing this module from the vehicle due to the fact that the cars equipped with stock fog lights need this so they would still be able to work.
The two wires you need to be focusing on are the ones attached to te photoresistor. One Will Be GREEN/BLACK, the other will be YELLOW/BLACK.
You will need to cut the YELLOW/BLACK wire leaving about 3 inches conected to the module. So you have some room to work with.
Then you will need to use a jumper connection, jump the YELLOW/BLACK wire to the GREEN/BLACK wire.
now your daytime running lights should be permanemtly off. If not contact me with your style beretta and i will figure it out.
Basic principle on why this works:
your drl's work off the photoresistor (the component that detects the level of light, centered on your dash under the metal strip). this component is normally closed, (power running through it) when there is a low level of light out, either cloud cover or night time this unit opens up (no power running through it), that's why if you cut that YELLOW/BLACK wire they will permanently stay on. that is why you will need to jump it to the GREEN/BLACK wire so that there is constant power running through it. (always closed) with constant power the photoreststor cannot open up and turn on the DRL's.
You may also be able to cut both wires and splice them, but i only wanted to cut one in case i was wrong, but it worked so I'm really not worried about going back in there just to cut another wire to splice them
How do you drain fuel tank on Chevy beretta?
You'll have to disconnect all the hoses, straps, and wires on gas tank. Drop it completely out from under the car and drain it from filler neck hole.... no other way besides using brass fixture to punch hole in bottom most section of tank, but this deems it unusable.
The availability of diagrams will depend on a few variables including the year of your vehicle and how much of the vehicle is factory original. For original equipment diagrams, check your local auto parts stores for repair books for your specific vehicle published by companies such as Chilton's or Haynes. You may also order or download many repair manuals and individual diagrams online. Modifications will require non-original diagrams which may be downloaded, or found through companies that specialize in racing equipment.
How do you install a supercharger on a 1994 Chevy Beretta Z26 2.3L quad 4 engine?
Installation instructions should have been furnished with your kit. ---- theres a supercharger for the quad??? wait..no there isnt! -berettaspeed15 ^^^^Do you even you your brain man???? Just swap the head over from a Twin Cam motor (same engine), and use the GM supercharger kit for a LD9, you'll see 300WHP easily, low compression with the head and about 6-8 psi. ;)
How do you install serpentine belt on a 1994 Chevy beretta z-26?
You have to pull the pulley up on the left side of the engine, towards the bottom of the serp. belt and then just pull it off. It helps if you start at the top of the belt and then work ur way down to the bottom. You might have to take the motor mount off to put the new belt on, I had a hard time, but I'm a girl, so that might explain the difficulties that i had. lol. Hope it helped.
