0
Chevy Beretta
This category covers questions about the Chevrolet Beretta, a compact sedan manufactured by General Motors and sold through its Chevrolet division. The Beretta went into production in 1987 and was discontinued in 1996, succeeded by the Chevrolet Malibu.
665 Questions
Where are the bright lights located in 94 Chevy Beretta?
Pull the turn signal towards you, push it back to turn them off.
How do you bleed a cooling system on a 1995 Beretta 3100 V6 when the bleeder valve is snapped?
The bleeder valve is the ONLY proper way of bleeding air out of the cooling system on a GM 3x00 engine. It is made up of two sections. A large section that threads into to the coolant rail vertical stem, and a smaller section that threads into the first one. The smaller section is the one you loosen to bleed, and is usually the part that snaps (it happened to me once). If that's the case, try replacing the entire lower section from a 3100 in a junkyard if you have access to one nearby. If not, someone on a Beretta forum such as bstuff(dot)com might be able to help you.
How do you change the headlight switch on a 1989 Chevy Beretta?
just pop out the switch or use a screwdriver to pop it out unplug the connecters and do the reverse to install it.
How do I recharge the AC on 1995 Beretta?
It will have to go to a garage with the correct equipment to evacuate the system and then recharge it, its not possible to do this at home.Hope this helps
Why is your 1996 Chevy beretta not shifting from first gear?
First, check transmission fluid levels, but typically once you loose a full gear, if the fluids topped off, your looking at a transmission rebuild.
Could be a faulty ground wire. Not very rare to happen
Where is the orifice tube located on a 1992 Beretta GT 6-cyclinder engine?
What orifice tube? An orifice tube is part of the AC system pull off the lines going into the accumulator. You'll see it. DoratheExplorer
How do you replace the thermostat located on a 1996 Chevy Beretta?
Follow the upper radiator hose back to the engine. where it connects. this should be the theromostat housing. take out a couple of bolts and your thermostat should be inside k. make sure you clean the old gasket materail off completely before installing the new one. hope this helps you wolverine
Where is the vehicle speed sensor located on a 1994 Pontiac Sunbird 3.1L?
In the 1994 2.0L engine sunbirds, the VSS is located above the passenger's side drive axle, I would imagine the location is the same for a 3.1.
How do you drop an oil pan on an 1989 Chevy Beretta GT?
Drain oil first, then remove the bolts that hold it up you will need a 10MM and mm Socket with extentions...
Where is the vehicle speed sensor on a 1993 Chevy beretta?
The VSS sensor is the vehicle speed sensor and it is located in the transmission. The purpose of it is to operate the speedometer and abs system.
Can oil leak from starter on a1995 Beretta 3.1?
No, the oil is more than likely from a leaking rear main seal or from the valve cover which may appear to be leaking at the starter. The starter uses no oil so it cannot leak oil.
Where is voltage regulator located on 1996 Chevy beretta?
The voltage regulator is built into the alternator.
Is the 1995 Chevy Beretta rear wheel or front wheel drive?
all berettas are front wheel drive, there are a few custom ones that have been changed for drag and road racing 1990-96 Chevrolet Beretta: Highlights When introduced during 1987, Chevy's compact, sporty front-drive coupe and its Corsica sedan mate became hot sellers. By 1990, the original engines were gone, as Berettas adopted a larger 2.2-liter four and a 3.1 liter V6. Making 135 horsepower, the V6 was standard in the GT coupe. A sporty GTZ with 180-horsepower Quad 4 engine joined the 1990 lineup, replacing the prior GTU. Year-to-Year Changes 1991 Chevrolet Beretta: A driver-side airbag arrived for 1991, and the high performance GTZ could get a V6 engine instead of the standard Quad 4. Accompanying the airbag was a new steering wheel, plus redesigned gauges and controls. 1992 Chevrolet Beretta: Antilock braking became standard for '92, as the base 2.2-liter engine added 15 horsepower. The 3.1-liter V6 again was standard on the GT and optional on base and GTZ Berettas. The GTZ continued to use a standard Quad 4 engine. 1993 Chevrolet Beretta: Base, GT, and GTZ models again went on sale, but the V6 that had been standard on the GT was now optional for all Berettas. The GT's Quad 4 engine dropped five horsepower, due to stricter emissions standards. 1994 Chevrolet Beretta: More-potent engines arrived, a Z26 with new Quad 4 engine replaced the GT/GTZ, and a 4-speed electronic automatic transmission joined the 3-speed. The new 2.2-liter 4-cylinder engine made 120 horsepower (up from 110), and the available V6 gained 20 horsepower (now rated at 160). The dual-overhead-cam 2.3-liter Quad 4 engine, installed in the Z26 coupe, developed 170 horsepower. The new electronic 4-speed automatic was the sole transmission choice for Berettas with V6 power. Door-mounted front shoulder belts replaced the former manual seatbelts. 1995 Chevrolet Beretta: Daytime running lights were added, and the Z26 got V6 power, deleting the Quad 4 engine. Automatic-transmission fluid and spark plugs now required no servicing for 100,000 miles under normal operating conditions. 1996 Chevrolet Beretta: For its final season, the front-drive coupe showed few changes.
What other cars do the Chevy Beretta wheels fit?
Some Cavalier and Pontiac fit the same wheels. Bolt pattern is 5x100.
How do you know if your car has bad fuel?
bad fuel will cause engine run rough stall out a lot vechicle wont start
How do you remove the steering column off of a 1994 Chevy Beretta?
Remove the lower dash panel and steering column cover. Disconnect all harnesses going to the column. There is a metal bracket attached to the steering column with brass-colored bolts, and attached to the underside of the dash with chrome-colored bolts. Remove only the chrome bolts. They're fairly long. Once completely removed, the entire steering column will drop slightly. Now pull back the plastic boot from the bottom of the steering column and look for the small bolt securing it in place. I believe it is 11mm. Loosen the bolt only enough for the column to slide out.
Where is the blinker relay in a 1995 Chevy beretta?
It should be under the dash, next to the steering column. You'll need to remove the kicker panel under the steering wheel to get to it (I believe its only 3 or 4 screws). I can't remember if it's on the left or right side of the column, but if your turn signals are still working, just turn them on and you should hear it clicking.
What does it mean when the brake light come on in your Chevy Beretta?
Check your brake fluid. The light will come on due to low fluid. Or someone has yanked your E-Brake.
Where are all the fuses located on 1989 Chevy beretta?
http://forum.topspeedautogroup.com/ thats all i can say...
How do change a heater blower on a 1989 beretta?
Remove your Alternator The blower is behind that. There are 3 bolts that you have to remove to get the Alternator off but before you do that you have to loosen the belt I used a bar and pulled down on to force the tensioner up and remove the belt then take your three bolts out of your alternator that holds it in place. Then there are aprox 6 screws that hold the blower motor in remove them. Make sure you disconnect the battery before you start taking things apart. Aprox time to remove and replace 1/2 hour. Good Luck
Probably yes to both.
Where is the fuel pressure test port on a 1995 Chevy Beretta?
There is no schrader valve, you need to source an adapter to place between where the fuel line attaches to the intake manifold.
